I'm having problems getting my Toshiba PDR-M70 (which is supposed to
act like a usb-storage device) to work. I'm using a 2.4.10 release
kernel and here is the output from running dmesg (usb stuff at the
bottom).
Thanks,
Michael
Linux version 2.4.10 (root@shakespeare) (gcc version 2.95.3 19991030 (prerelease)) #1
Tue Sep 25 17:39:24 EDT 2001
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000005ffec000 (usable)
BIOS-e820: 000000005ffec000 - 000000005ffef000 (ACPI data)
BIOS-e820: 000000005ffef000 - 000000005ffff000 (reserved)
BIOS-e820: 000000005ffff000 - 0000000060000000 (ACPI NVS)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
On node 0 totalpages: 229376
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/sda1
Initializing CPU#0
Detected 1275.930 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2542.79 BogoMIPS
Memory: 900776k/917504k available (1175k kernel code, 16340k reserved, 383k data, 200k
init, 0k highmem)
Dentry-cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount-cache hash table entries: 16384 (order: 5, 131072 bytes)
Buffer-cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Before vendor init, caps: 0183f9ff c1c7f9ff 00000000, vendor = 2
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After vendor init, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: After generic, caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: Common caps: 0183f9ff c1c7f9ff 00000000 00000000
CPU: AMD Athlon(tm) Processor stepping 04
Enabling fast FPU save and restore... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
PCI: PCI BIOS revision 2.10 entry at 0xf1150, last bus=1
PCI: Using configuration type 1
PCI: Probing PCI hardware
Unknown bridge resource 0: assuming transparent
PCI: Using IRQ router VIA [1106/0686] at 00:04.0
Applying VIA southbridge workaround.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP
enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
block: 128 slots per queue, batch=16
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller on PCI bus 00 dev 21
PCI: Enabling device 00:04.1 (0000 -> 0001)
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: neither IDE port enabled (BIOS)
PDC20265: IDE controller on PCI bus 00 dev 88
PCI: Found IRQ 10 for device 00:11.0
PCI: Sharing IRQ 10 with 00:0b.0
PDC20265: chipset revision 2
PDC20265: not 100% native mode: will probe irqs later
ide2: BM-DMA at 0x8400-0x8407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0x8408-0x840f, BIOS settings: hdg:pio, hdh:pio
Linux Tulip driver version 0.9.15-pre6 (July 2, 2001)
PCI: Found IRQ 15 for device 00:0d.0
PCI: Sharing IRQ 15 with 00:04.2
PCI: Sharing IRQ 15 with 00:04.3
tulip0: EEPROM default media type Autosense.
tulip0: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block.
tulip0: MII transceiver #1 config 3000 status 7829 advertising 01e1.
eth0: Digital DS21143 Tulip rev 65 at 0xa000, 00:C0:F0:6B:80:8D, IRQ 15.
SCSI subsystem driver Revision: 1.00
PCI: Found IRQ 10 for device 00:0b.0
PCI: Sharing IRQ 10 with 00:11.0
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.1
<Adaptec 29160 Ultra160 SCSI adapter>
aic7892: Ultra160 Wide Channel A, SCSI Id=7, 32/255 SCBs
Vendor: IBM Model: DDYS-T36950N Rev: S93E
Type: Direct-Access ANSI SCSI revision: 03
scsi0:0:6:0: Tagged Queuing enabled. Depth 253
Attached scsi disk sda at scsi0, channel 0, id 6, lun 0
(scsi0:A:6): 160.000MB/s transfers (80.000MHz DT, offset 63, 16bit)
SCSI device sda: 71687340 512-byte hdwr sectors (36704 MB)
Partition check:
sda: sda1
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 200k freed
usb-uhci.c: $Revision: 1.268 $ time 17:42:10 Sep 25 2001
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 15 for device 00:04.2
PCI: Sharing IRQ 15 with 00:04.3
PCI: Sharing IRQ 15 with 00:0d.0
usb-uhci.c: USB UHCI at I/O 0xd400, IRQ 15
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
usb.c: kmalloc IF f7587600, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: d400
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface f7587600
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
PCI: Found IRQ 15 for device 00:04.3
PCI: Sharing IRQ 15 with 00:04.2
PCI: Sharing IRQ 15 with 00:0d.0
usb-uhci.c: USB UHCI at I/O 0xd000, IRQ 15
usb-uhci.c: Detected 2 ports
hub.c: port 1 connection change
hub.c: port 1, portstatus 300, change 3, 1.5 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 100, change 3, 12 Mb/s
hub.c: port 1 enable change, status 300
hub.c: port 2 enable change, status 100
usb.c: new USB bus registered, assigned bus number 2
usb.c: kmalloc IF f7587720, numif 1
usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
usb.c: USB device number 1 default language ID 0x0
Product: USB UHCI Root Hub
SerialNumber: d000
hub.c: USB hub found
hub.c: 2 ports detected
hub.c: standalone hub
hub.c: ganged power switching
hub.c: global over-current protection
hub.c: Port indicators are not supported
hub.c: power on to power good time: 2ms
hub.c: hub controller current requirement: 0mA
hub.c: port removable status: RR
hub.c: local power source is good
hub.c: no over-current condition exists
hub.c: enabling power on all ports
usb.c: hub driver claimed interface f7587720
usb.c: kusbd: /sbin/hotplug add 1
usb.c: kusbd policy returned 0xfffffffe
usb-uhci.c: v1.268:USB Universal Host Controller Interface driver
hub.c: port 1 connection change
hub.c: port 1, portstatus 300, change 3, 1.5 Mb/s
hub.c: port 2 connection change
hub.c: port 2, portstatus 300, change 3, 1.5 Mb/s
hub.c: port 1 enable change, status 300
hub.c: port 2 enable change, status 300
eth0: Setting full-duplex based on MII#1 link partner capability of 41e1.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
hub.c: port 2 connection change
hub.c: port 2, portstatus 101, change 1, 12 Mb/s
hub.c: port 2, portstatus 103, change 0, 12 Mb/s
hub.c: USB new device connect on bus1/2, assigned device number 2
usb.c: kmalloc IF f49837e0, numif 1
usb.c: new device strings: Mfr=1, Product=2, SerialNumber=0
usb.c: USB device number 2 default language ID 0x409
Manufacturer: TOSHIBA ?PDR-M70 ??[
Product: PDR-M70 ??[
usb-storage: act_altsettting is 0
usb-storage: id_index calculated to be: 52
usb-storage: Array length appears to be: 54
usb-storage: USB Mass Storage device detected
usb-storage: Endpoints: In: 0xf5d307a0 Out: 0xf5d307b4 Int: 0x00000000 (Period 0)
usb-uhci.c: ENXIO 80000280, flags 0, urb f6802960, burb f6802860
usb-uhci.c: ENXIO 80000280, flags 0, urb f6802960, burb f6802860
usb-storage: New GUID 113243310000000000000000
usb-uhci.c: interrupt, status 2, frame# 1402
usb_control/bulk_msg: timeout
usb-storage: GetMaxLUN command result is -110, data is 246
usb-storage: Transport: Bulk
usb-storage: Protocol: Transparent SCSI
usb-storage: *** thread sleeping.
scsi1 : SCSI emulation for USB Mass Storage devices
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command INQUIRY (6 bytes)
usb-storage: 12 00 00 00 ff 00 18 c0 50 a7 e0 c1
usb-storage: Bulk command S 0x43425355 T 0xe7f Trg 0 LUN 0 L 255 F 128 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: usb_stor_transfer_partial(): xfer 255 bytes
usb-storage: command_abort() called
usb-storage: usb_stor_bulk_msg() returned -2 xferred 64/255
usb-storage: usb_stor_transfer_partial(): transfer aborted
usb-storage: Bulk data transfer result 0x3
usb-storage: -- transport indicates command was aborted
usb-storage: Fixing INQUIRY data to show SCSI rev 2
usb-storage: scsi command aborted
usb-storage: *** thread sleeping.
usb-storage: queuecommand() called
usb-storage: *** thread awakened.
usb-storage: Command TEST_UNIT_READY (6 bytes)
usb-storage: 00 00 00 00 00 00 18 c0 50 a7 e0 c1
usb-storage: Bulk command S 0x43425355 T 0xe7f Trg 0 LUN 0 L 0 F 0 CL 6
usb-storage: Bulk command transfer result=0
usb-storage: Attempting to get CSW...
usb-uhci.c: interrupt, status 3, frame# 221
usb-storage: clearing endpoint halt for pipe 0xc0008280
usb_control/bulk_msg: timeout
usb-storage: Attempting to get CSW (2nd try)...
usb-storage: clearing halt for pipe 0xc0008280
usb_control/bulk_msg: timeout
usb-storage: Bulk reset requested
usb-storage: command_abort() called
usb-storage: -- nothing to abort
usb-storage: device_reset() called
usb-storage: Bulk reset requested
usb-uhci.c: ENXIO 80000200, flags 0, urb f6802560, burb f68025e0
usb-storage: Bulk soft reset failed -6
usb-storage: bus_reset() called
usb_control/bulk_msg: timeout
usb-storage: Bulk soft reset failed -110
usb-storage: -- transport indicates transport failure
usb-storage: Fixing INQUIRY data to show SCSI rev 2
usb-storage: scsi cmd done, result=0x70000
usb-storage: *** thread sleeping.
usb_control/bulk_msg: timeout
usb-uhci.c: ENXIO 80000280, flags 0, urb f6802a60, burb f68025e0
usb-uhci.c: ENXIO 80000280, flags 0, urb f6802a60, burb f68025e0
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
usb_control/bulk_msg: timeout
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
