The Olympus reader works fine. I can mount it as /dev/sda1 to a mount point and read the memory card. It shows up in Hardware Browser as /dev/sda.
The Soyo reader is recognized by the system, but I can't figure out how to get it assigned to a scsi device and functioning.
If this is the wrong place to ask about this, please point me elsewhere.
Below are some of the results of probing I've done trying to understand the system and problem. I apologize for the long post, but do not yet know what is of interest.
Descriptions in usbview: ======================== SCM eUSB SmartMedia Manufacturer: SCM Microsystems Inc. Speed: 12Mb/s (full) USB Version: 1.00 Device Class: 00(>ifc ) Device Subclass: 00 Device Protocol: 00 Maximum Default Endpoint Size: 64 Number of Configurations: 1 Vendor Id: 066b Product Id: 0105 Revision Number: 1.00
Config Number: 1
Number of Interfaces: 1
Attributes: 80
MaxPower Needed: 100mA Interface Number: 0
Name: usb-storage
Alternate Number: 0
Class: ff(vend.)
Sub Class: 0
Protocol: 0
Number of Endpoints: 3 Endpoint Address: 01
Direction: out
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0ms Endpoint Address: 82
Direction: in
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0ms Endpoint Address: 83
Direction: in
Attribute: 3
Type: Int.
Max Packet Size: 64
Interval: 255msSOYO USB Storage Device Manufacturer: SOYO Technologies Corp. Serial Number: 0AEC501000001A002 Speed: 12Mb/s (full) USB Version: 1.10 Device Class: 00(>ifc ) Device Subclass: 00 Device Protocol: 00 Maximum Default Endpoint Size: 16 Number of Configurations: 1 Vendor Id: 0aec Product Id: 5010 Revision Number: 1.00
Config Number: 1
Number of Interfaces: 1
Attributes: 80
MaxPower Needed: 100mA Interface Number: 0
Name: usb-storage
Alternate Number: 0
Class: 08(stor.)
Sub Class: 6
Protocol: 50
Number of Endpoints: 2 Endpoint Address: 01
Direction: out
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0ms Endpoint Address: 82
Direction: in
Attribute: 2
Type: Bulk
Max Packet Size: 64
Interval: 0msexcerpts from /proc/bus/usb/devices ===================================
T: Bus=04 Lev=01 Prnt=01 Port=01 Cnt=02 Dev#= 3 Spd=12 MxCh= 0 D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=066b ProdID=0105 Rev= 1.00 S: Manufacturer=SCM Microsystems Inc. S: Product=SCM eUSB SmartMedia C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=usb-storage E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=255ms
T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=16 #Cfgs= 1 P: Vendor=0aec ProdID=5010 Rev= 1.00 S: Manufacturer= SOYO Technologies Corp. S: Product= SOYO USB Storage Device S: SerialNumber=0AEC501000001A002 C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr=100mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage E: Ad=01(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
Contents of /proc/scsi/scsi ===========================
Attached devices: Host: scsi0 Channel: 00 Id: 00 Lun: 00 Vendor: Olympus Model: Camedia MAUSB-2 Rev: 0100 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi2 Channel: 00 Id: 00 Lun: 00 Vendor: SAMSUNG Model: CD-R/RW SW-240B Rev: R402 Type: CD-ROM ANSI SCSI revision: 02 Host: scsi2 Channel: 00 Id: 01 Lun: 00 Vendor: TOSHIBA Model: DVD-ROM SD-M1212 Rev: 1R22 Type: CD-ROM ANSI SCSI revision: 02
Output of cdrecord -scanbus ===========================
[EMAIL PROTECTED] log]# cdrecord -scanbus
Cdrecord 2.0 (i686-pc-linux-gnu) Copyright (C) 1995-2002 Jrg Schilling
Linux sg driver version: 3.1.24
Using libscg version 'schily-0.7'
cdrecord: Warning: using inofficial libscg transport code version (schily - Red Hat-scsi-linux-sg.c-1.75-RH '@(#)scsi-linux-sg.c 1.75 02/10/21 Copyright 1997 J. Schilling').
scsibus0:
0,0,0 0) 'Olympus' 'Camedia MAUSB-2' '0100' Removable Disk
0,1,0 1) *
0,2,0 2) *
0,3,0 3) *
0,4,0 4) *
0,5,0 5) *
0,6,0 6) *
0,7,0 7) *
scsibus2:
2,0,0 200) 'SAMSUNG ' 'CD-R/RW SW-240B ' 'R402' Removable CD-ROM
2,1,0 201) 'TOSHIBA ' 'DVD-ROM SD-M1212' '1R22' Removable CD-ROM
2,2,0 202) *
2,3,0 203) *
2,4,0 204) *
2,5,0 205) *
2,6,0 206) *
2,7,0 207) *
[EMAIL PROTECTED] log]#
Excerpts from dmesg ===================
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
ehci-hcd 00:0e.2: VIA Technologies, Inc. USB 2.0
ehci-hcd 00:0e.2: irq 10, pci mem f8849000
usb.c: new USB bus registered, assigned bus number 1
PCI: 00:0e.2 PCI cache line size set incorrectly (32 bytes) by BIOS/FW.
PCI: 00:0e.2 PCI cache line size corrected to 64.
ehci-hcd 00:0e.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 4 ports detected
usb-uhci.c: $Revision: 1.275 $ time 07:04:31 May 29 2003
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xa400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xa800, IRQ 5
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xc800, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 4
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xcc00, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 5
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,8), internal journal
Adding Swap: 1028120k swap-space (priority -1)
hub.c: new USB device 00:11.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x4b8/0x10b) is not claimed by any active driver.
hub.c: new USB device 00:11.2-2, assigned address 3
usb.c: USB device 3 (vend/prod 0x66b/0x105) is not claimed by any active driver.
hub.c: new USB device 00:0e.0-1, assigned address 2
usb.c: USB device 2 (vend/prod 0xaec/0x5010) is not claimed by any active driver.
usb.c: registered new driver usbscanner
scanner.c: USB scanner device (0x04b8/0x010b) now attached to scanner0
scanner.c: 0.4.12:USB Scanner Driver
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Olympus Model: Camedia MAUSB-2 Rev: 0100
Type: Direct-Access ANSI SCSI revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 3
scsi1 : SCSI emulation for USB Mass Storage devices
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,10), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
MSDOS FS: IO charset iso8859-1
MSDOS FS: Using codepage 850
hdc: attached ide-scsi driver.
hdd: attached ide-scsi driver.
scsi2 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: SAMSUNG Model: CD-R/RW SW-240B Rev: R402
Type: CD-ROM ANSI SCSI revision: 02
Vendor: TOSHIBA Model: DVD-ROM SD-M1212 Rev: 1R22
Type: CD-ROM ANSI SCSI revision: 02
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
Attached scsi CD-ROM sr0 at scsi2, channel 0, id 0, lun 0
Attached scsi CD-ROM sr1 at scsi2, channel 0, id 1, lun 0
sr0: scsi3-mmc drive: 40x/40x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
sr1: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
ip_tables: (C) 2000-2002 Netfilter core team
8139too Fast Ethernet driver 0.9.26
divert: allocating divert_blk for eth0
eth0: RealTek RTL8139 Fast Ethernet at 0xf895c000, 00:50:2c:04:81:b6, IRQ 11
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting 100mbps full-duplex based on auto-negotiated partner ability 45e1.
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
lp0: using parport0 (polling).
lp0: console ready
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: Detected Via Apollo Pro KT266 chipset
agpgart: AGP aperture is 64M @ 0xe8000000
[drm] AGP 0.99 on VIA Apollo KT133 @ 0xe8000000 64MB
[drm] Initialized radeon 1.7.0 20020828 on minor 0
spurious 8259A interrupt: IRQ7.
cmpci: version $Revision: 5.64 $ time 07:04:08 May 29 2003
cmpci: found CM8738 adapter at io 0xc000 irq 10
cmpci: chip version = 055
cmpci: Enable SPDIF loop
ide-floppy: hdb: I/O error, pc = 0, key = 2, asc = 3a, ascq = 0
ide-floppy: hdb: I/O error, pc = 1b, key = 2, asc = 3a, ascq = 0
hdb: No disk in drive
ide-floppy: hdb: I/O error, pc = 1e, key = 2, asc = 3a, ascq = 0
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
usb-uhci.c: interrupt, status 3, frame# 2006
sddr09: Found Flash card, ID = 98 E6 00 00: Manuf. Toshiba, 8 MB
SCSI device sda: 16000 512-byte hdwr sectors (8 MB)
sda: Write Protect is off
sda: sda1
=========================================
Thanks.
Gerry Tool
------------------------------------------------------- This SF.Net email sponsored by: Parasoft Error proof Web apps, automate testing & more. Download & eval WebKing and get a free book. www.parasoft.com/bulletproofapps1 _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
