-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1
Hi there...
This mouse works on my notebook (2.6.0-test11) but fails on my desktop (2.6.2 and 2.6.0-test4). Motherboard is A7V333X.
I plug it in, it seems to be recognized, and than there seems to be total mess; USB bus is totally unresponsive afterwords.
System is a vanilla 2.6.2 (well some "private" audio patches, but other USB devices like Quickcam Express work fine).
Loaded modules for USB: either uhci_hcd or uhci_hcd and ehci_hcd - same results.
Here is the (much too) detailed log: drivers/usb/host/uhci-hcd.c: USB Universal Host Controller Interface driver v2.1 uhci_hcd 0000:00:10.0: UHCI Host Controller uhci_hcd 0000:00:10.0: irq 21, io base 0000d800 uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1 drivers/usb/host/uhci-hcd.c: detected 2 ports uhci_hcd 0000:00:10.0: root hub device address 1 usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb1: Product: UHCI Host Controller usb usb1: Manufacturer: Linux 2.6.2-echoaudio uhci_hcd usb usb1: SerialNumber: 0000:00:10.0 drivers/usb/core/usb.c: usb_hotplug usb usb1: registering 1-0:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: ganged power switching hub 1-0:1.0: global over-current protection hub 1-0:1.0: Port indicators are not supported hub 1-0:1.0: power on to power good time: 2ms hub 1-0:1.0: hub controller current requirement: 0mA hub 1-0:1.0: local power source is good hub 1-0:1.0: no over-current condition exists hub 1-0:1.0: enabling power on all ports uhci_hcd 0000:00:10.1: UHCI Host Controller uhci_hcd 0000:00:10.1: irq 21, io base 0000d400 uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2 drivers/usb/host/uhci-hcd.c: detected 2 ports uhci_hcd 0000:00:10.1: root hub device address 1 usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb2: Product: UHCI Host Controller usb usb2: Manufacturer: Linux 2.6.2-echoaudio uhci_hcd usb usb2: SerialNumber: 0000:00:10.1 drivers/usb/core/usb.c: usb_hotplug usb usb2: registering 2-0:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug hub 2-0:1.0: usb_probe_interface hub 2-0:1.0: usb_probe_interface - got id hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected hub 2-0:1.0: standalone hub hub 2-0:1.0: ganged power switching hub 2-0:1.0: global over-current protection hub 2-0:1.0: Port indicators are not supported hub 2-0:1.0: power on to power good time: 2ms hub 2-0:1.0: hub controller current requirement: 0mA hub 2-0:1.0: local power source is good hub 2-0:1.0: no over-current condition exists hub 2-0:1.0: enabling power on all ports uhci_hcd 0000:00:10.2: UHCI Host Controller uhci_hcd 0000:00:10.2: irq 21, io base 0000d000 uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3 drivers/usb/host/uhci-hcd.c: detected 2 ports uhci_hcd 0000:00:10.2: root hub device address 1 usb usb3: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb3: Product: UHCI Host Controller usb usb3: Manufacturer: Linux 2.6.2-echoaudio uhci_hcd usb usb3: SerialNumber: 0000:00:10.2 drivers/usb/core/usb.c: usb_hotplug hub 1-0:1.0: port 1, status 300, change 3, 1.5 Mb/s hub 1-0:1.0: port 2, status 100, change 3, 12 Mb/s usb usb3: registering 3-0:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug hub 3-0:1.0: usb_probe_interface hub 3-0:1.0: usb_probe_interface - got id hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected hub 3-0:1.0: standalone hub hub 3-0:1.0: ganged power switching hub 3-0:1.0: global over-current protection hub 3-0:1.0: Port indicators are not supported hub 3-0:1.0: power on to power good time: 2ms hub 3-0:1.0: hub controller current requirement: 0mA hub 3-0:1.0: local power source is good hub 3-0:1.0: no over-current condition exists hub 3-0:1.0: enabling power on all ports hub 2-0:1.0: port 1, status 100, change 3, 12 Mb/s hub 2-0:1.0: port 2, status 100, change 3, 12 Mb/s hub 1-0:1.0: port 1 enable change, status 300 hub 1-0:1.0: port 2 enable change, status 100 hub 3-0:1.0: port 1, status 300, change 3, 1.5 Mb/s hub 3-0:1.0: port 2, status 100, change 3, 12 Mb/s hub 2-0:1.0: port 1 enable change, status 100 hub 2-0:1.0: port 2 enable change, status 100 hub 3-0:1.0: port 1 enable change, status 300 hub 3-0:1.0: port 2 enable change, status 100 drivers/usb/host/uhci-hcd.c: d800: suspend_hc drivers/usb/host/uhci-hcd.c: d400: suspend_hc drivers/usb/host/uhci-hcd.c: d000: suspend_hc ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 64 ehci_hcd 0000:00:10.3: EHCI Host Controller ehci_hcd 0000:00:10.3: reset hcs_params 0x3206 dbg=0 cc=3 pcc=2 ordered !ppc ports=6 ehci_hcd 0000:00:10.3: reset hcc_params 6872 thresh 7 uframes 256/512/1024 ehci_hcd 0000:00:10.3: capability 0001 at 68 ehci_hcd 0000:00:10.3: irq 21, pci mem e0bed000 ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4 ehci_hcd 0000:00:10.3: reset command 080002 (park)=0 ithresh=8 period=1024 Reset HALT ehci_hcd 0000:00:10.3: init command 010009 (park)=0 ithresh=1 period=256 RUN ehci_hcd 0000:00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29 ehci_hcd 0000:00:10.3: root hub device address 1 usb usb4: new device strings: Mfr=3, Product=2, SerialNumber=1 drivers/usb/core/message.c: USB device number 1 default language ID 0x409 usb usb4: Product: EHCI Host Controller usb usb4: Manufacturer: Linux 2.6.2-echoaudio ehci_hcd usb usb4: SerialNumber: 0000:00:10.3 drivers/usb/core/usb.c: usb_hotplug usb usb4: registering 4-0:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug hub 4-0:1.0: usb_probe_interface hub 4-0:1.0: usb_probe_interface - got id hub 4-0:1.0: USB hub found hub 4-0:1.0: 6 ports detected hub 4-0:1.0: standalone hub hub 4-0:1.0: ganged power switching hub 4-0:1.0: individual port over-current protection hub 4-0:1.0: Single TT hub 4-0:1.0: TT requires at most 8 FS bit times hub 4-0:1.0: Port indicators are not supported hub 4-0:1.0: power on to power good time: 20ms hub 4-0:1.0: hub controller current requirement: 0mA hub 4-0:1.0: local power source is good hub 4-0:1.0: no over-current condition exists hub 4-0:1.0: enabling power on all ports ehci_hcd 0000:00:10.3: GetStatus port 6 status 001803 POWER sig=j CSC CONNECT hub 4-0:1.0: port 6, status 501, change 1, 480 Mb/s hub 4-0:1.0: debounce: port 6: delay 100ms stable 4 status 0x501 ehci_hcd 0000:00:10.3: port 6 full speed --> companion ehci_hcd 0000:00:10.3: GetStatus port 6 status 003801 POWER OWNER sig=j ~ CONNECT drivers/usb/host/uhci-hcd.c: d000: wakeup_hc hub 3-0:1.0: port 2, status 101, change 1, 12 Mb/s hub 3-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101 hub 3-0:1.0: new USB device on port 2, assigned address 2 usb 3-2: new device strings: Mfr=0, Product=1, SerialNumber=0 drivers/usb/core/message.c: USB device number 2 default language ID 0x409 usb 3-2: Product: Camera drivers/usb/core/usb.c: usb_hotplug usb 3-2: registering 3-2:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug ehci_hcd 0000:00:10.3: GetStatus port 4 status 001403 POWER sig=k CSC CONNECT hub 4-0:1.0: port 4, status 501, change 1, 480 Mb/s hub 4-0:1.0: debounce: port 4: delay 100ms stable 4 status 0x501 ehci_hcd 0000:00:10.3: port 4 low speed --> companion ehci_hcd 0000:00:10.3: GetStatus port 4 status 003402 POWER OWNER sig=k CSC ehci_hcd 0000:00:10.3: GetStatus port 6 status 003802 POWER OWNER sig=j CSC hub 4-0:1.0: port 6, status 0, change 1, 12 Mb/s hub 2-0:1.0: port 2, status 301, change 1, 1.5 Mb/s drivers/usb/host/uhci-hcd.c: d400: wakeup_hc hub 2-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x301 hub 2-0:1.0: new USB device on port 2, assigned address 2 usb 2-2: new device strings: Mfr=1, Product=2, SerialNumber=0 drivers/usb/core/message.c: USB device number 2 default language ID 0x409 usb 2-2: Product: Cypress Ultra Mouse usb 2-2: Manufacturer: Cypress Semi. drivers/usb/core/usb.c: usb_hotplug usb 2-2: registering 2-2:1.0 (config #1, interface 0) drivers/usb/core/usb.c: usb_hotplug hid 2-2:1.0: usb_probe_interface hid 2-2:1.0: usb_probe_interface - got id drivers/usb/host/uhci-hcd.c: uhci_result_control() failed with status 500000 [ce634270] link (0e6341b2) element (0e62e080) ~ Element != First TD ~ 0: [ce62e040] link (0e62e080) e3 LS Length=7 MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=0e189060) ~ 1: [ce62e080] link (0e62e0c0) e3 LS Stalled Babble Length=0 MaxLen=0 DT1 EndPt=0 Dev=2, PID=69(IN) (buf=0e189080) ~ 2: [ce62e0c0] link (00000001) e3 LS IOC Active Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=e1(OUT) (buf=00000000)
drivers/usb/input/hid-core.c: ctrl urb status -75 received usb 2-2: control timeout on ep0out
*******************************************
I tried to google, but I found nothing. The error-codes suggests that this is a hardware/firmware problem, so I'll try to update my BIOS now, hope that helps :(
If anyone has any additional ideas what might help, please let me know *sigh*
thanks in advance, ~ Lars
-----BEGIN PGP SIGNATURE----- Version: GnuPG v1.2.3 (GNU/Linux) Comment: Using GnuPG with Thunderbird - http://enigmail.mozdev.org
iD8DBQFALCoC7V+LJJ0V3jwRAlU7AJ9BC0yI8DpiH3JhcI6d9LX55vaAyACggSSt 3xUNdwmg4rLuGPYVpkSlJK8= =nY0C -----END PGP SIGNATURE-----
------------------------------------------------------- SF.Net is sponsored by: Speed Start Your Linux Apps Now. Build and deploy apps & Web services for Linux with a free DVD software kit from IBM. Click Now! http://ads.osdn.com/?ad_id=1356&alloc_id=3438&op=click _______________________________________________ [EMAIL PROTECTED] To unsubscribe, use the last form field at: https://lists.sourceforge.net/lists/listinfo/linux-usb-users
