Hi Luc,
It looks like you have a problem with "not accepting address",
there are some suggestions in the FAQ for that.
regards,
Stephen.
On Fri, 23 Jul 2004 [EMAIL PROTECTED] wrote:
> Dears,
> May be a new challenge for you the USB Gurus :-).
>
> I just acquired a Camcorder Sony DCR-HC40(E).
> I use a Mandrake 10.0 with an upgraded kernel 2.6.7.
> I can capture the video stream from the IEEE1394 on my desktop. No problem.
> On my laptop, I only have a USB port and I would like also to catch the 'live
> video stream' from its USB port (not the pictures saved on the memory stick. I
> can already do that thanks to Leon and Stephen). It is feasable under Wins....I
> would like to make it work on my favorite OS :-).
>
> The /proc/bus/usb/devices is not very verbose...anyway, here is a snapshot:
>
>
> T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
> B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
> D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
> P: Vendor=0000 ProdID=0000 Rev= 2.06
> S: Manufacturer=Linux 2.6.7 uhci_hcd
> S: Product=Intel Corp. 82801CA/CAM USB (Hub #1)
> S: SerialNumber=0000:00:1d.0
> C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
> I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
> E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
>
> As I was not convinced by the details in the syslogs, I recompiled my kernel
> 2.6.7 with a higher USB trace mode, and here is the output in the syslog:
>
>
> Jul 22 22:02:56 bikini kernel: uhci_hcd 0000:00:1d.0: wakeup_hc
> Jul 22 22:02:56 bikini kernel: uhci_hcd 0000:00:1d.0: port 1 portsc 0082
> Jul 22 22:02:56 bikini kernel: hub 1-0:1.0: port 1, status 0100, change 0001,
> 12 Mb/s
> Jul 22 22:02:58 bikini kernel: uhci_hcd 0000:00:1d.0: suspend_hc
> Jul 22 22:03:01 bikini kernel: uhci_hcd 0000:00:1d.0: wakeup_hc
> Jul 22 22:03:01 bikini kernel: uhci_hcd 0000:00:1d.0: port 1 portsc 0093
> Jul 22 22:03:01 bikini kernel: hub 1-0:1.0: port 1, status 0101, change 0001,
> 12 Mb/s
> Jul 22 22:03:01 bikini kernel: hub 1-0:1.0: debounce: port 1: delay 100ms
> stable 4 status 0x101
> Jul 22 22:03:02 bikini kernel: usb 1-1: new full speed USB device using address
> 2
> Jul 22 22:03:02 bikini kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
> failed with status 500000
> Jul 22 22:03:02 bikini kernel: [f76f6240] link (376f61e2) element (376f4080)
> Jul 22 22:03:02 bikini kernel: Element != First TD
> Jul 22 22:03:02 bikini kernel: 0: [f76f4040] link (376f4080) e3 Length=7
> MaxLen=7 DT0 EndPt=0 Dev=2, PID=2d(SETUP) (buf=34e29148)
> Jul 22 22:03:02 bikini kernel: 1: [f76f4080] link (376f40c0) e3 SPD Stalled
> Babble Length=7 MaxLen=7 DT1 EndPt=0 Dev=2, PID=69(IN) (buf=363e19e8)
> Jul 22 22:03:02 bikini kernel: 2: [f76f40c0] link (00000001) e3 IOC Active
> Length=0 MaxLen=7ff DT1 EndPt=0 Dev=2, PID=e1(OUT) (buf=00000000)
> Jul 22 22:03:02 bikini kernel:
> Jul 22 22:03:02 bikini kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
> failed with status 440000
> Jul 22 22:03:02 bikini kernel: [f76f6240] link (376f61e2) element (376f4040)
> Jul 22 22:03:02 bikini kernel: 0: [f76f4040] link (376f4080) e0 Stalled
> CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=363e19e8)
> Jul 22 22:03:02 bikini kernel: 1: [f76f4080] link (00000001) e3 IOC Active
> Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
> Jul 22 22:03:02 bikini kernel:
> Jul 22 22:03:02 bikini kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
> failed with status 440000
> Jul 22 22:03:02 bikini kernel: [f76f6240] link (376f61e2) element (376f4040)
> Jul 22 22:03:02 bikini kernel: 0: [f76f4040] link (376f4080) e0 Stalled
> CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=363e19e8)
> Jul 22 22:03:02 bikini kernel: 1: [f76f4080] link (00000001) e3 IOC Active
> Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
> Jul 22 22:03:02 bikini kernel:
> Jul 22 22:03:02 bikini kernel: usb 1-1: device not accepting address 2, error -
> 71
> Jul 22 22:03:02 bikini kernel: usb 1-1: new full speed USB device using address
> 3
> Jul 22 22:03:02 bikini kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
> failed with status 500000
> Jul 22 22:03:02 bikini kernel: [f76f6240] link (376f61e2) element (376f4080)
> Jul 22 22:03:02 bikini kernel: Element != First TD
> Jul 22 22:03:02 bikini kernel: 0: [f76f4040] link (376f4080) e3 Length=7
> MaxLen=7 DT0 EndPt=0 Dev=3, PID=2d(SETUP) (buf=34e29148)
> Jul 22 22:03:02 bikini kernel: 1: [f76f4080] link (376f40c0) e3 SPD Stalled
> Babble Length=7 MaxLen=7 DT1 EndPt=0 Dev=3, PID=69(IN) (buf=363e19e8)
> Jul 22 22:03:02 bikini kernel: 2: [f76f40c0] link (00000001) e3 IOC Active
> Length=0 MaxLen=7ff DT1 EndPt=0 Dev=3, PID=e1(OUT) (buf=00000000)
> Jul 22 22:03:02 bikini kernel:
> Jul 22 22:03:02 bikini kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
> failed with status 440000
> Jul 22 22:03:02 bikini kernel: [f76f6240] link (376f61e2) element (376f4040)
> Jul 22 22:03:02 bikini kernel: 0: [f76f4040] link (376f4080) e0 Stalled
> CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=363e19e8)
> Jul 22 22:03:02 bikini kernel: 1: [f76f4080] link (00000001) e3 IOC Active
> Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
> Jul 22 22:03:02 bikini kernel:
> Jul 22 22:03:02 bikini kernel: uhci_hcd 0000:00:1d.0: uhci_result_control:
> failed with status 440000
> Jul 22 22:03:02 bikini kernel: [f76f6240] link (376f61e2) element (376f4040)
> Jul 22 22:03:02 bikini kernel: 0: [f76f4040] link (376f4080) e0 Stalled
> CRC/Timeo Length=7 MaxLen=7 DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=363e19e8)
> Jul 22 22:03:02 bikini kernel: 1: [f76f4080] link (00000001) e3 IOC Active
> Length=0 MaxLen=7ff DT1 EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
> Jul 22 22:03:02 bikini kernel:
> Jul 22 22:03:03 bikini kernel: usb 1-1: device not accepting address 3, error -
> 71
>
> Any advice ? Any more details I could provide ?
> Thanks to all of you for your support,
>
> Luc
>
> -------------------------------------------------
> This mail sent through IMP: http://horde.org/imp/
>
>
> -------------------------------------------------------
> This SF.Net email is sponsored by BEA Weblogic Workshop
> FREE Java Enterprise J2EE developer tools!
> Get your free copy of BEA WebLogic Workshop 8.1 today.
> http://ads.osdn.com/?ad_id=4721&alloc_id=10040&op=click
> _______________________________________________
> [EMAIL PROTECTED]
> To unsubscribe, use the last form field at:
> https://lists.sourceforge.net/lists/listinfo/linux-usb-users
>
--
/------------------------------------+-------------------------\
|Stephen J. Gowdy | SLAC, MailStop 34, |
|http://www.slac.stanford.edu/~gowdy/ | 2575 Sand Hill Road, |
|http://calendar.yahoo.com/gowdy | Menlo Park CA 94025, USA |
|EMail: [EMAIL PROTECTED] | Tel: +1 650 926 3144 |
\------------------------------------+-------------------------/
-------------------------------------------------------
This SF.Net email is sponsored by BEA Weblogic Workshop
FREE Java Enterprise J2EE developer tools!
Get your free copy of BEA WebLogic Workshop 8.1 today.
http://ads.osdn.com/?ad_id=4721&alloc_id=10040&op=click
_______________________________________________
[EMAIL PROTECTED]
To unsubscribe, use the last form field at:
https://lists.sourceforge.net/lists/listinfo/linux-usb-users
