Hi
I bought last saturday a Philips PCVC860K Webcam and want to use it. It is the
very first hardware I want to use at an usb-interface.
I have installed the original 2.2.14-kernel and already patched it with the
newest raid-0.90-patch and the agpgart-patch. Both worked fine. I use the
SuSE-6.4 distribution but have changed to the original 2.2.14-sources to
install the raid-0.90-patch cleanly.
Now I have installed the usb-2.3.50-1-for-2.2.14.diff patch also.
I enabled USB, usb-uhci, and audio support in the .config file and built a new
kernel. My system has an EPOX MVP3-G mainboard with the VIA-MVP3-chipset and
2 USB-ports.
Here is the corresponding part of my /var/log/messages file after rebooting
(with reflects the commands 'modprobe usb-uhci' and 'modprobe audio' in
/sbin/init.d/boot.local which returned without errors):
Apr 16 22:10:32 server kernel: scsi logging level set to 0x00000038
Apr 16 22:10:32 server kernel: usb-uhci.c: version v1.184 time 21:07:07 Apr 15 2000
Apr 16 22:10:32 server kernel: usb-uhci.c: Detected 2 ports
Apr 16 22:10:32 server kernel: usb.c: new USB bus registered, assigned bus number 1
Apr 16 22:10:32 server kernel: usb.c: USB new device connect, assigned device number 1
Apr 16 22:10:32 server kernel: usb.c: kmalloc IF c49ef220, numif 1
Apr 16 22:10:32 server kernel: usb.c: new device strings: Mfr=0, Product=0,
SerialNumber=0
Apr 16 22:10:32 server kernel: hub.c: USB hub found
Apr 16 22:10:32 server kernel: hub.c: 2 ports detected
Apr 16 22:10:32 server kernel: hub.c: ganged power switching
Apr 16 22:10:32 server kernel: hub.c: standalone hub
Apr 16 22:10:32 server kernel: hub.c: global over-current protection
Apr 16 22:10:32 server kernel: hub.c: power on to power good time: 2ms
Apr 16 22:10:32 server kernel: hub.c: hub controller current requirement: 0mA
Apr 16 22:10:32 server kernel: hub.c: port 1 is removable
Apr 16 22:10:32 server kernel: hub.c: port 2 is removable
Apr 16 22:10:32 server kernel: hub.c: local power source is good
Apr 16 22:10:32 server kernel: hub.c: no over-current condition exists
Apr 16 22:10:32 server kernel: hub.c: enabling power on all ports
Apr 16 22:10:32 server kernel: usb.c: usb-bandwidth-alloc: was: 0, new: 17, bustime =
17 us, Pipe allowed: yes
Apr 16 22:10:32 server kernel: usb.c: bw_alloc bumped to 17 for 1 requesters
Apr 16 22:10:32 server kernel: usb.c: hub driver claimed interface c49ef220
Apr 16 22:10:32 server kernel: Length = 18
Apr 16 22:10:32 server kernel: DescriptorType = 01
Apr 16 22:10:32 server kernel: USB version = 1.00
Apr 16 22:10:32 server kernel: Vendor:Product = 0000:0000
Apr 16 22:10:32 server kernel: MaxPacketSize0 = 8
Apr 16 22:10:32 server kernel: NumConfigurations = 1
Apr 16 22:10:32 server kernel: Device version = 0.00
Apr 16 22:10:32 server kernel: Device Class:SubClass:Protocol = 09:00:00
Apr 16 22:10:32 server kernel: Hub device class
Apr 16 22:10:32 server kernel: Configuration:
Apr 16 22:10:32 server kernel: bLength = 9
Apr 16 22:10:32 server kernel: bDescriptorType = 02
Apr 16 22:10:32 server kernel: wTotalLength = 0019
Apr 16 22:10:32 server kernel: bNumInterfaces = 01
Apr 16 22:10:32 server kernel: bConfigurationValue = 01
Apr 16 22:10:32 server kernel: iConfiguration = 00
Apr 16 22:10:32 server kernel: bmAttributes = 40
Apr 16 22:10:32 server kernel: MaxPower = 0mA
Apr 16 22:10:32 server kernel:
Apr 16 22:10:32 server kernel: Interface: 0
Apr 16 22:10:32 server kernel: Alternate Setting: 0
Apr 16 22:10:32 server kernel: bLength = 9
Apr 16 22:10:32 server kernel: bDescriptorType = 04
Apr 16 22:10:32 server kernel: bInterfaceNumber = 00
Apr 16 22:10:32 server kernel: bAlternateSetting = 00
Apr 16 22:10:32 server kernel: bNumEndpoints = 01
Apr 16 22:10:32 server kernel: bInterface Class:SubClass:Protocol = 09:00:00
Apr 16 22:10:32 server kernel: iInterface = 00
Apr 16 22:10:32 server kernel: Endpoint:
Apr 16 22:10:32 server kernel: bLength = 7
Apr 16 22:10:32 server kernel: bDescriptorType = 05
Apr 16 22:10:32 server kernel: bEndpointAddress = 81 (in)
Apr 16 22:10:32 server kernel: bmAttributes = 03 (Interrupt)
Apr 16 22:10:32 server kernel: wMaxPacketSize = 0008
Apr 16 22:10:32 server kernel: bInterval = ff
Apr 16 22:10:32 server kernel: usb.c: registered new driver audio
Apr 16 22:10:33 server kernel: hub.c: port 1 connection change
Apr 16 22:10:33 server kernel: hub.c: portstatus 101, change 3, High Speed
Apr 16 22:10:33 server kernel: hub.c: portstatus 103, change 0, High Speed
Apr 16 22:10:33 server kernel: usb.c: USB new device connect, assigned device number 2
Apr 16 22:10:33 server kernel: usb-uhci.c: interrupt, status 2, frame# 1373
Apr 16 22:10:33 server kernel: usb-uhci-debug.h: uhci_show_td c4b34780 (04B34780)
Apr 16 22:10:33 server kernel: usb-uhci-debug.h: MaxLen=05 DT1 EndPt=0 Dev=2, PID=69(
IN ) (buf=04b4dde0)
Apr 16 22:10:33 server kernel: usb-uhci-debug.h: Len=05 e3 Stalled Babble
Apr 16 22:10:33 server kernel: usb-uhci-debug.h: Breadth first, link points to TD @
04b347c0
Apr 16 22:10:33 server kernel: usb.c: couldn't get all of config descriptors
Apr 16 22:10:33 server kernel: usb.c: unable to get configuration (error=-32)
Apr 16 22:10:33 server kernel: hub.c: hub: disabling port 1
Apr 16 22:10:33 server kernel: hub.c: port 1 enable change, status 101
Apr 16 22:10:33 server kernel: hub.c: already running port 1 disabled by hub (EMI?),
re-enabling...
Apr 16 22:10:33 server kernel: hub.c: portstatus 101, change 0, High Speed
Apr 16 22:10:33 server kernel: usb.c: USB disconnect on device -1
Apr 16 22:10:33 server kernel: hub.c: portstatus 103, change 0, High Speed
Apr 16 22:10:33 server kernel: usb.c: USB new device connect, assigned device number 2
Apr 16 22:10:33 server kernel: Serial driver version 4.27 with HUB-6 MANY_PORTS
MULTIPORT SHARE_IRQ enabled
Apr 16 22:10:33 server kernel: ttyS00 at 0x03f8 (irq = 4) is a 16550A
Apr 16 22:10:33 server kernel: ttyS01 at 0x02f8 (irq = 3) is a 16550A
Apr 16 22:10:33 server kernel: CSLIP: code copyright 1989 Regents of the University of
California
Apr 16 22:10:33 server kernel: ISDN subsystem Rev: 1.93/1.80/1.95/1.60/1.17/1.3 loaded
Apr 16 22:10:33 server kernel: HiSax: Linux Driver for passive ISDN cards
Apr 16 22:10:33 server kernel: HiSax: Version 3.3c (module)
Apr 16 22:10:33 server kernel: HiSax: Layer1 Revision 2.36
Apr 16 22:10:33 server kernel: HiSax: Layer2 Revision 2.20
Apr 16 22:10:33 server kernel: HiSax: TeiMgr Revision 2.13
Apr 16 22:10:33 server kernel: HiSax: Layer3 Revision 2.10
Apr 16 22:10:33 server kernel: HiSax: LinkLayer Revision 2.40
Apr 16 22:10:33 server kernel: HiSax: Approval certification valid
Apr 16 22:10:33 server kernel: HiSax: Approved with ELSA Quickstep series cards
Apr 16 22:10:33 server kernel: HiSax: Approval registration numbers:
Apr 16 22:10:33 server kernel: HiSax: German D133361J CETECOM ICT Services GmbH
Apr 16 22:10:33 server kernel: HiSax: EU (D133362J) CETECOM ICT Services GmbH
Apr 16 22:10:33 server kernel: HiSax: Approved with Eicon Technology Diva 2.01 PCI
cards
Apr 16 22:10:33 server kernel: HiSax: Total 1 card defined
Apr 16 22:10:33 server kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax (0)
Apr 16 22:10:33 server kernel: HiSax: Elsa driver Rev. 2.20
Apr 16 22:10:33 server kernel: Elsa: QS 1000 defined at 0x160 IRQ 5
Apr 16 22:10:33 server kernel: Elsa: timer OK; resetting card
Apr 16 22:10:33 server kernel: Elsa: ISAC version (0): 2086/2186 V1.1
Apr 16 22:10:33 server kernel: Elsa: HSCX version A: V2.1 B: V2.1
Apr 16 22:10:33 server kernel: Elsa Quickstep: IRQ 5 count 0
Apr 16 22:10:33 server kernel: Elsa Quickstep: IRQ 5 count 3
Apr 16 22:10:33 server kernel: Elsa: 14 timer tics in 110 msek
Apr 16 22:10:33 server kernel: Elsa: timer and irq OK
Apr 16 22:10:33 server kernel: HiSax: DSS1 Rev. 2.21
Apr 16 22:10:33 server kernel: HiSax: 2 channels added
Apr 16 22:10:33 server kernel: HiSax: MAX_WAITING_CALLS added
Apr 16 22:10:33 server kernel: HiSax: debugging flags card 1 set to 0
Apr 16 22:10:33 server kernel: 3Com 3c90x Version 1.0.0 1999 <[EMAIL PROTECTED]>
Apr 16 22:10:33 server kernel: usb_control/bulk_msg: timeout
Apr 16 22:10:33 server kernel: ippp, open, slot: 0, minor: 0, state: 0000
Apr 16 22:10:33 server kernel: ippp_ccp: allocated reset data structure cdfc5800
Apr 16 22:10:33 server kernel: usb_control/bulk_msg: timeout
Apr 16 22:10:33 server kernel: nfsd_fh_init : initialized fhcache, entries=512
Apr 16 22:10:33 server kernel: usb_control/bulk_msg: timeout
Apr 16 22:10:34 server last message repeated 2 times
Apr 16 22:10:34 server kernel: usb.c: USB device not responding, giving up (error=-110)
Apr 16 22:10:34 server kernel: hub.c: hub: disabling port 1
Apr 16 22:10:34 server kernel: hub.c: port 2 connection change
Apr 16 22:10:34 server kernel: hub.c: portstatus 300, change 3, Low Speed
Apr 16 22:10:34 server kernel: hub.c: port 2 enable change, status 300
Apr 16 22:10:38 server sshd[279]: log: Server listening on port 22.
Apr 16 22:10:38 server sshd[279]: log: Generating 768 bit RSA key.
Apr 16 22:10:38 server sshd[279]: log: RSA key generation complete.
Apr 16 22:10:38 server /usr/sbin/cron[295]: (CRON) STARTUP (fork ok)
Apr 16 22:10:38 server in.identd[299]: started
Apr 16 22:10:43 server kernel: Linux agpgart interface v0.99 (c) Jeff Hartmann
Apr 16 22:10:43 server kernel: agpgart: Maximum main memory to use for agp memory: 204M
Apr 16 22:10:43 server kernel: agpgart: Detected a VIA VP3 Chipset.
Apr 16 22:10:43 server kernel: agpgart: Physical address of the agp aperture:
0xe0000000
Apr 16 22:10:43 server kernel: agpgart: Agp aperture is 64M in size.
Apr 16 22:10:43 server su: (to adabas) root on /dev/console
Apr 16 22:10:43 server PAM-unix2[425]: session started for user adabas, service su
Apr 16 22:10:46 server kernel: AgentMon uses obsolete /proc/pci interface
Apr 16 22:10:47 server PAM-unix2[425]: session finished for user adabas, service su
Apr 16 22:10:47 server su: (to adabas) root on /dev/console
Apr 16 22:10:47 server PAM-unix2[447]: session started for user adabas, service su
Apr 16 22:10:48 server PAM-unix2[447]: session finished for user adabas, service su
Due to these usb-errors (I think at least) there is no /proc/bus/usb created.
To me, all these usb-debuging output says nearly nothing.
Hope you can give me any help to solve my driver-problem.
Thanks in advance,
achim
--
Achim Flammenkamp FSP Mathematisierung Universit�t Bielefeld
Universit�tsstraBe 25 33501 Bielefeld Federal Republic of Germany
POB 100131 http://www.uni-bielefeld.de/~achim/ [EMAIL PROTECTED]
(+49)(0)521-106-3852 UTC+2=MEDST < Game of Life and Go Fan >
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
