Hi,
I got a flashcard reader from a company calles SCM (Delivered with my Nikon
Coolpix camera). I tried following the description for installing the reader,
but i never reach the point where the device is supposed to register itself as
a scsi host.
It recognizes the device as a new USB device when loading the usb-storage
module, but responds with:
-----
May 9 02:02:56 styx kernel: Manufacturer: Shuttle Technology Inc.
May 9 02:02:56 styx kernel: Product: E-USB Bridge
May 9 02:02:56 styx kernel: ov511: probing for device...
May 9 02:02:56 styx kernel: usb.c: unhandled interfaces on device
May 9 02:02:56 styx kernel: usb.c: This device is not recognized by
any installed USB driver.
-----
I tried probing around the source and maillist archive and found something
about "unusual devices", but I cannot figure out where to register this one.
The USB system is working, my Creative Webcam3 is working without problems at
all.
Could anyone perhaps point me in the right direction?
yours,
Jesper Angelo
Denmark
---
May 9 02:02:55 styx kernel: usb-uhci.c: $Revision: 1.50 $ time 01:39:21 May 8
2000
May 9 02:02:55 styx kernel: usb-uhci.c: High bandwidth mode enabled
May 9 02:02:55 styx kernel: usb-uhci.c: Intel USB controller: setting latency
timer to 0
May 9 02:02:55 styx kernel: usb-uhci.c: Detected 2 ports
May 9 02:02:56 styx kernel: usb.c: new USB bus registered, assigned bus number
1
May 9 02:02:56 styx kernel: usb.c: USB new device connect, assigned device
number 1
May 9 02:02:56 styx kernel: usb.c: kmalloc IF c78fb220, numif 1
May 9 02:02:56 styx kernel: usb.c: new device strings: Mfr=0, Product=0,
SerialNumber=0
May 9 02:02:56 styx kernel: ov511: probing for device...
May 9 02:02:56 styx kernel: hub.c: USB hub found
May 9 02:02:56 styx kernel: hub.c: 2 ports detected
May 9 02:02:56 styx kernel: hub.c: ganged power switching
May 9 02:02:56 styx kernel: hub.c: standalone hub
May 9 02:02:56 styx kernel: hub.c: global over-current protection
May 9 02:02:56 styx kernel: hub.c: power on to power good time: 2ms
May 9 02:02:56 styx kernel: hub.c: hub controller current requirement: 0mA
May 9 02:02:56 styx kernel: hub.c: port 1 is removable
May 9 02:02:56 styx kernel: hub.c: port 2 is removable
May 9 02:02:56 styx kernel: hub.c: local power source is good
May 9 02:02:56 styx kernel: hub.c: no over-current condition exists
May 9 02:02:56 styx kernel: hub.c: enabling power on all ports
May 9 02:02:56 styx kernel: usb.c: usb-bandwidth-alloc: was: 0, new: 17,
bustime = 17 us, Pipe allowed: yes
May 9 02:02:56 styx kernel: usb.c: bw_alloc bumped to 17 for 1 requesters
May 9 02:02:56 styx kernel: usb.c: hub driver claimed interface c78fb220
May 9 02:02:56 styx kernel: hub.c: port 2 connection change
May 9 02:02:56 styx kernel: hub.c: portstatus 101, change 1, High Speed
May 9 02:02:56 styx kernel: hub.c: portstatus 103, change 0, High Speed
May 9 02:02:56 styx kernel: usb.c: USB new device connect, assigned device
number 2
May 9 02:02:56 styx kernel: usb.c: kmalloc IF c298ce80, numif 1
May 9 02:02:56 styx kernel: usb.c: new device strings: Mfr=1, Product=2,
SerialNumber=0
May 9 02:02:56 styx kernel: usb.c: USB device number 2 default language ID
0x409
May 9 02:02:56 styx kernel: Manufacturer: Shuttle Technology Inc.
May 9 02:02:56 styx kernel: Product: E-USB Bridge
May 9 02:02:56 styx kernel: ov511: probing for device...
May 9 02:02:56 styx kernel: usb.c: unhandled interfaces on device
May 9 02:02:56 styx kernel: usb.c: This device is not recognized by any
installed USB driver.
May 9 02:02:56 styx kernel: Length = 18
May 9 02:02:56 styx kernel: DescriptorType = 01
May 9 02:02:56 styx kernel: USB version = 1.00
May 9 02:02:56 styx kernel: Vendor:Product = 066b:0103
May 9 02:02:56 styx kernel: MaxPacketSize0 = 64
May 9 02:02:56 styx kernel: NumConfigurations = 1
May 9 02:02:56 styx kernel: Device version = 2.00
May 9 02:02:56 styx kernel: Device Class:SubClass:Protocol = 00:00:00
May 9 02:02:56 styx kernel: Per-interface classes
May 9 02:02:56 styx kernel: Configuration:
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
