Maybe one of the writers of the device driver can help you (rather than an
ignoramus like me). However I would suggest that you send the (relevant)
dmesg output with ONLY the USB-Ethernet device connected and in both
orders. (So used rmmod to remove the kaweth driver, lsmod to check that it
is gone, plug in the device and then insmod the driver etc). Your errors look
very much like those I get by loading the driver first. On the other hand
it could be something else!
What is the thing actually called? There might (horrors) be two devices
with the same manufactor/device identifiers.
RBM
On 12 Jun, hashimoh wrote:
> Sory for late to answer.
>
> I was trying to follow your advice.
> But, problem still is same.
> I am starting to think that my adaptor is really ATEN?
> If you have any other suggestion, please let me know.
>
> Thanks again,
>
> Hashimoh
>
> [EMAIL PROTECTED] wrote:
>
>> Make sure the usb-ethernet is connected BEFORE you load the driver -- or
>> try rmmod'ing the driver and insmod'ing it again.
>>
>> RBM
>>
>> On 9 Jun, hashimoh wrote:
>> > I also am trying to use my ATEM Ethernet USB
>> >
>> > Adaptor.
>> >
>> > I am now applying Micheal's kaweth driver
>> >
>> > 0.2.1(thank you). But I failed to recognize.
>> >
>> > Here is a output of dmesg and contents of
>> >
>> > /proc/bus/usb/devices
>> >
>> > Any suggestions are welcome.
>> >
>> > Thanks.
>> >
>> > Hisashi
>> >
>> > PS.
>> >
>> > In my environment, order of 'insmod', pluggin device
>> >
>> > does not have any effect to recognition.
>> >
>> > ---------------------------
>> >
>> > Envirionment Kernel 2.2.14 + backport patch usb-2.3.99-pre7-1-for-2.2.14.diff.gz
>> >
>> > output of dmesg(only related parts)
>> >
>> > usb.c: registered new driver usbdevfs
>> > usb.c: registered new driver hub
>> > usb-uhci.c: $Revision: 1.228 $ time 23:03:48 May 12 2000
>> > usb-uhci.c: High bandwidth mode enabled
>> > usb-uhci.c: Intel USB controller: setting latency timer to 0
>> > usb-uhci.c: USB UHCI at I/O 0xfce0, IRQ 10
>> > usb-uhci.c: Detected 2 ports
>> > usb.c: new USB bus registered, assigned bus number 1
>> > usb.c: USB new device connect, assigned device number 1
>> > usb.c: kmalloc IF c0e0bb20, numif 1
>> > usb.c: new device strings: Mfr=0, Product=2, SerialNumber=1
>> > usb.c: USB device number 1 default language ID 0x0
>> > Product: USB UHCI Root Hub
>> > SerialNumber: fce0
>> > hub.c: USB hub found
>> > hub.c: 2 ports detected
>> > hub.c: ganged power switching
>> > hub.c: standalone hub
>> > hub.c: global over-current protection
>> > hub.c: power on to power good time: 2ms
>> > hub.c: hub controller current requirement: 0mA
>> > hub.c: port 1 is removable
>> > hub.c: port 2 is removable
>> > hub.c: local power source is good
>> > hub.c: no over-current condition exists
>> > hub.c: enabling power on all ports
>> > usb.c: hub driver claimed interface c0e0bb20
>> > Kawasaki USB->Ethernet Driver loading...
>> > usb.c: registered new driver kaweth
>> > usb.c: registered new driver hid
>> > mice: PS/2 mouse device common for all mice
>> > usb.c: registered new driver usblp
>> > registered device ppp0
>> > hub.c: port 1 connection change
>> > hub.c: portstatus 101, change 1, High Speed
>> > hub.c: portstatus 103, change 0, High Speed
>> > usb.c: USB new device connect, assigned device number 2
>> > usb.c: kmalloc IF c2c0a3c0, numif 1
>> > usb.c: new device strings: Mfr=2, Product=3, SerialNumber=1
>> > usb.c: USB device number 2 default language ID 0x409
>> > Manufacturer: ATEN Inc.
>> > Product: USB-Ethernet
>> > SerialNumber: 001074003548
>> > usb-uhci.c: interrupt, status 2, frame# 1844
>> > Kawasaki Device Probe (Device number:2): 0x0557:0x2002
>> > Device at c1871b40
>> > Descriptor length: 12 type: 1
>> > D-Link DSB-650 connected...
>> > Reading kaweth configuration
>> > Request type: c0 Request: 0 Value: 0 Index: 0 Length: 12
>> > usb-uhci.c: interrupt, status 2, frame# 1846
>> > usb-uhci-debug.h: TD @ c0d4b8e0/00D4B8E0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0440
>> > usb-uhci-debug.h: Len=07 e0 Stalled CRC/Timeo
>> > usb-uhci-debug.h: Link points to TD @ 00d4b9e0, Breadth first
>> > kaweth control message failed (urb addr: c0f97d20)
>> > usb-uhci.c: interrupt, status 2, frame# 1849
>> > usb-uhci-debug.h: TD @ c0d4b860/00D4B860, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
>> > usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
>> > usb-uhci-debug.h: Link points to TD @ 00d4ba20, Breadth first
>> > usb-uhci.c: interrupt, status 2, frame# 1851
>> > usb-uhci-debug.h: TD @ c0d4b960/00D4B960, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
>> > usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
>> > usb-uhci-debug.h: Link points to TD @ 00d4b7e0, Breadth first
>> > Actual length: 0, length 18
>> > Resetting...
>> > usb-uhci.c: interrupt, status 2, frame# 1854
>> > usb-uhci-debug.h: TD @ c0d4ba20/00D4BA20, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0440
>> > usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
>> > usb-uhci-debug.h: Link points to TD @ 00d4b860, Breadth first
>> > Downloading firmware at c38a4ab8 to kaweth device at c1794000...
>> > Firmware length: 3838
>> > Request type: 40 Request: ff Value: 0 Index: 0 Length: efe
>> > usb-uhci.c: interrupt, status 2, frame# 1868
>> > usb-uhci-debug.h: TD @ c0d4b7e0/00D4B7E0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0440
>> > usb-uhci-debug.h: Len=07 e0 Stalled CRC/Timeo
>> > usb-uhci-debug.h: Link points to TD @ 00d4b960, Breadth first
>> > kaweth control message failed (urb addr: c0f97d20)
>> > usb-uhci.c: interrupt, status 2, frame# 1870
>> > usb-uhci-debug.h: TD @ c0d4b860/00D4B860, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
>> > usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
>> > usb-uhci-debug.h: Link points to TD @ 00d4ba20, Breadth first
>> > usb-uhci.c: interrupt, status 2, frame# 1873
>> > usb-uhci-debug.h: TD @ c0d4bfa0/00D4BFA0, MaxLen=07 DT0 EP=0 Dev=2 PID=(SETUP)
>buf=024d0680
>> > usb-uhci-debug.h: Len=07 e0 SPD Stalled CRC/Timeo
>> > usb-uhci-debug.h: Link points to TD @ 00d4bf60, Breadth first
>> > Actual length: 0, length 3838
>> > Error downloading firmware (-110), no net device created
>> > usb.c: unhandled interfaces on device
>> > usb.c: This device is not recognized by any installed USB driver.
>> > Length = 18
>> > DescriptorType = 01
>> > USB version = 1.00
>> > Vendor:Product = 0557:2002
>> > MaxPacketSize0 = 8
>> > NumConfigurations = 1
>> > Device version = 0.02
>> > Device Class:SubClass:Protocol = 00:00:00
>> > Per-interface classes
>> > Configuration:
>> > bLength = 9
>> > bDescriptorType = 02
>> > wTotalLength = 0027
>> > bNumInterfaces = 01
>> > bConfigurationValue = 01
>> > iConfiguration = 00
>> > bmAttributes = 80
>> > MaxPower = 90mA
>> >
>> > Interface: 0
>> > Alternate Setting: 0
>> > bLength = 9
>> > bDescriptorType = 04
>> > bInterfaceNumber = 00
>> > bAlternateSetting = 00
>> > bNumEndpoints = 03
>> > bInterface Class:SubClass:Protocol = 00:00:00
>> > iInterface = 00
>> > Endpoint:
>> > bLength = 7
>> > bDescriptorType = 05
>> > bEndpointAddress = 81 (in)
>> > bmAttributes = 02 (Bulk)
>> > wMaxPacketSize = 0040
>> > bInterval = 00
>> > Endpoint:
>> > bLength = 7
>> > bDescriptorType = 05
>> > bEndpointAddress = 02 (out)
>> > bmAttributes = 02 (Bulk)
>> > wMaxPacketSize = 0040
>> > bInterval = 00
>> > Endpoint:
>> > bLength = 7
>> > bDescriptorType = 05
>> > bEndpointAddress = 83 (in)
>> > bmAttributes = 03 (Interrupt)
>> > wMaxPacketSize = 0008
>> > bInterval = 01
>> > ---------------------------------------------------------
>> >
>> > contents of /proc/bus/usb/devices
>> >
>> > T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
>> > B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
>> > D: Ver= 1.00 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>> > P: Vendor=0000 ProdID=0000 Rev= 0.00
>> > S: Product=USB UHCI Root Hub
>> > S: SerialNumber=fce0
>> > C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
>> > I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
>> > E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=255ms
>> > T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0
>> > D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>> > P: Vendor=0557 ProdID=2002 Rev= 0.02
>> > C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 90mA
>> > I: If#= 0 Alt= 0 #EPs= 3 Cls=00(>ifc ) Sub=00 Prot=00 Driver=(none)
>> > E: Ad=81(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
>> > E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
>> > E: Ad=83(I) Atr=03(Int.) MxPS= 8 Ivl= 1ms
>> >
>> > --
>> > ---------------------------------
>> > Hashimoto Hisashi(Hitachi@HP NJL)
>> > [EMAIL PROTECTED]
>> > ---------------------------------
>> >
>> >
>> >
>> >
>> > ---------------------------------------------------------------------
>> > To unsubscribe, e-mail: [EMAIL PROTECTED]
>> > For additional commands, e-mail: [EMAIL PROTECTED]
>> >
>
> --
> ---------------------------------
> Hashimoto Hisashi(Hitachi@HP NJL)
> [EMAIL PROTECTED]
> ---------------------------------
>
>
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [EMAIL PROTECTED]
> For additional commands, e-mail: [EMAIL PROTECTED]
>
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
