On Thu, May 03, 2018 at 02:36:13AM +0530, Manu Gautam wrote: > To improve eye diagram for PHYs on different boards of same SOC, > some parameters may need to be changed. Provide device tree > properties to override these from board specific device tree > files. While at it, replace "qcom,qusb2-v2-phy" with compatible > string for USB2 PHY on sdm845 which was earlier added for > sdm845 only. > > Signed-off-by: Manu Gautam <mgau...@codeaurora.org> > --- > .../devicetree/bindings/phy/qcom-qusb2-phy.txt | 23 +++++++++++++- > include/dt-bindings/phy/phy-qcom-qusb2.h | 37 > ++++++++++++++++++++++ > 2 files changed, 59 insertions(+), 1 deletion(-) > create mode 100644 include/dt-bindings/phy/phy-qcom-qusb2.h > > diff --git a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt > b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt > index 42c9742..03025d9 100644 > --- a/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt > +++ b/Documentation/devicetree/bindings/phy/qcom-qusb2-phy.txt > @@ -6,7 +6,7 @@ QUSB2 controller supports LS/FS/HS usb connectivity on > Qualcomm chipsets. > Required properties: > - compatible: compatible list, contains > "qcom,msm8996-qusb2-phy" for 14nm PHY on msm8996, > - "qcom,qusb2-v2-phy" for QUSB2 V2 PHY. > + "qcom,sdm845-qusb2-phy" for 10nm PHY on sdm845. > > - reg: offset and length of the PHY register set. > - #phy-cells: must be 0. > @@ -27,6 +27,27 @@ Optional properties: > tuning parameter value for qusb2 phy. > > - qcom,tcsr-syscon: Phandle to TCSR syscon register region. > + - qcom,imp-res-offset-value: It is a 6 bit value that specifies offset to be > + added to PHY refgen RESCODE via IMP_CTRL1 register. It is a PHY > + tuning parameter that may vary for different boards of same SOC. > + This property is applicable to only QUSB2 v2 PHY (sdm845). > + - qcom,hstx-trim-value: It is a 4 bit value that specifies tuning for HSTX > + output current. > + Possible range is - 15mA to 24mA (stepsize of 600 uA). > + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. > + This property is applicable to only QUSB2 v2 PHY (sdm845). > + Default value is 22.2mA for sdm845. > + - qcom,preemphasis-level: It is a 2 bit value that specifies pre-emphasis > level. > + Possible range is 0 to 15% (stepsize of 5%). > + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. > + This property is applicable to only QUSB2 v2 PHY (sdm845). > + Default value is 10% for sdm845. > +- qcom,preemphasis-width: It is a 1 bit value that specifies how long the > HSTX > + pre-emphasis (specified using qcom,preemphasis-level) must be in > + effect. Duration could be half-bit of full-bit.
s/of/or/ But I'd just make this a boolean instead: qcom,preemphasis-half-bit > + See dt-bindings/phy/phy-qcom-qusb2.h for applicable values. > + This property is applicable to only QUSB2 v2 PHY (sdm845). > + Default value is full-bit width for sdm845. -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html