The status quo on i.MX6 is that if "over-current-active-high" is specified in the device tree this is configured as expected. If the property is missing polarity isn't changed and so the polarity is kept as setup by the bootloader. Reset default is active high, so active low can only be used with help by the bootloader. On i.MX7 it is similar, but there disabling of over current detection has a similar inconsistency.
This patch introduces a new property that allows to explicitly configure for active low over current detection and consistently sets this up. In the absence of an explicit configuration the bit is kept as is. On i.MX7 over current detection is used unless disabled in the device tree. Signed-off-by: Uwe Kleine-König <u.kleine-koe...@pengutronix.de> --- .../devicetree/bindings/usb/ci-hdrc-usb2.txt | 5 ++-- drivers/usb/chipidea/ci_hdrc_imx.c | 16 ++++++++--- drivers/usb/chipidea/ci_hdrc_imx.h | 8 +++++- drivers/usb/chipidea/usbmisc_imx.c | 28 ++++++++++++++----- 4 files changed, 43 insertions(+), 14 deletions(-) diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt index 529e51879fb2..c32f6e983cf6 100644 --- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt +++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt @@ -87,8 +87,9 @@ i.mx specific properties - fsl,usbmisc: phandler of non-core register device, with one argument that indicate usb controller index - disable-over-current: disable over current detect -- over-current-active-high: over current signal polarity is high active, - typically over current signal polarity is low active. +- over-current-active-low: over current signal polarity is active low. +- over-current-active-high: over current signal polarity is active high. + It's recommended to specify the over current polarity. - external-vbus-divider: enables off-chip resistor divider for Vbus Example: diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c b/drivers/usb/chipidea/ci_hdrc_imx.c index 09b37c0d075d..18b0ca87799c 100644 --- a/drivers/usb/chipidea/ci_hdrc_imx.c +++ b/drivers/usb/chipidea/ci_hdrc_imx.c @@ -132,11 +132,19 @@ static struct imx_usbmisc_data *usbmisc_get_init_data(struct device *dev) data->dev = &misc_pdev->dev; - if (of_find_property(np, "disable-over-current", NULL)) + /* + * Check the various over current related properties. If over current + * detection is disabled we're not interested in the polarity. + */ + if (of_find_property(np, "disable-over-current", NULL)) { data->disable_oc = 1; - - if (of_find_property(np, "over-current-active-high", NULL)) - data->oc_polarity = 1; + } else if (of_find_property(np, "over-current-active-high", NULL)) { + data->oc_pol_active_low = 0; + data->oc_pol_configured = 1; + } else if (of_find_property(np, "over-current-active-low", NULL)) { + data->oc_pol_active_low = 1; + data->oc_pol_configured = 1; + } if (of_find_property(np, "external-vbus-divider", NULL)) data->evdo = 1; diff --git a/drivers/usb/chipidea/ci_hdrc_imx.h b/drivers/usb/chipidea/ci_hdrc_imx.h index 204275f47573..640721fef0d7 100644 --- a/drivers/usb/chipidea/ci_hdrc_imx.h +++ b/drivers/usb/chipidea/ci_hdrc_imx.h @@ -11,7 +11,13 @@ struct imx_usbmisc_data { int index; unsigned int disable_oc:1; /* over current detect disabled */ - unsigned int oc_polarity:1; /* over current polarity if oc enabled */ + + /* true if over-current polarity is active low */ + unsigned int oc_pol_active_low:1; + + /* true if dt specifies polarity */ + unsigned int oc_pol_configured:1; + unsigned int evdo:1; /* set external vbus divider option */ unsigned int ulpi:1; /* connected to an ULPI phy */ }; diff --git a/drivers/usb/chipidea/usbmisc_imx.c b/drivers/usb/chipidea/usbmisc_imx.c index def80ff547e4..4a8de1b37f67 100644 --- a/drivers/usb/chipidea/usbmisc_imx.c +++ b/drivers/usb/chipidea/usbmisc_imx.c @@ -340,11 +340,17 @@ static int usbmisc_imx6q_init(struct imx_usbmisc_data *data) reg = readl(usbmisc->base + data->index * 4); if (data->disable_oc) { reg |= MX6_BM_OVER_CUR_DIS; - } else if (data->oc_polarity == 1) { - /* High active */ - reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY); } else { - reg &= ~(MX6_BM_OVER_CUR_DIS); + reg &= ~MX6_BM_OVER_CUR_DIS; + + /* + * If the polarity is not configured keep it as setup by the + * bootloader. + */ + if (data->oc_pol_configured && data->oc_pol_active_low) + reg |= MX6_BM_OVER_CUR_POLARITY; + else if (data->oc_pol_configured) + reg &= ~MX6_BM_OVER_CUR_POLARITY; } writel(reg, usbmisc->base + data->index * 4); @@ -444,9 +450,17 @@ static int usbmisc_imx7d_init(struct imx_usbmisc_data *data) reg = readl(usbmisc->base); if (data->disable_oc) { reg |= MX6_BM_OVER_CUR_DIS; - } else if (data->oc_polarity == 1) { - /* High active */ - reg &= ~(MX6_BM_OVER_CUR_DIS | MX6_BM_OVER_CUR_POLARITY); + } else { + reg &= ~MX6_BM_OVER_CUR_DIS; + + /* + * If the polarity is not configured keep it as setup by the + * bootloader. + */ + if (data->oc_pol_configured && data->oc_pol_active_low) + reg |= MX6_BM_OVER_CUR_POLARITY; + else if (data->oc_pol_configured) + reg &= ~MX6_BM_OVER_CUR_POLARITY; } writel(reg, usbmisc->base); -- 2.19.2