On Mon, 2019-06-24 at 16:40 +0200, Philipp Zabel wrote:
> Hi,
>
> On Mon, 2018-05-21 at 15:03 -0700, Curt Meyers wrote:
> > On 05/16/2018 04:55 AM, Mathias Nyman wrote:
> > > On 15.05.2018 12:22, Michael Tretter wrote:
> > > > Hi Mathias,
> > > >
> > > > On Tue, 10 Apr 2018 18:22:03 +0300, Mathias Nyman wrote:
> > > > > On 09.04.2018 11:21, Michael Tretter wrote:
> > > > > > On Tue, 20 Feb 2018 15:29:28 +0200, Mathias Nyman wrote:
> > > > > > > On 16.02.2018 15:28, Michael Tretter wrote:
> > > > > > > > On Mon, 29 Jan 2018 14:02:57 +0200, Mathias Nyman wrote:
> > > > > > > > > On 19.01.2018 22:12, Philipp Zabel wrote:
> > > > > > > > > > On Fri, Jan 19, 2018 at 2:10 PM, Michael Tretter
> > > > > > > > > > <[email protected]> wrote:
> > > > > > > > > > > I found the old thread and it sounds exactly like my
> > > > > > > > > > > issue.
> > > > > > > > > > > Different
> > > > > > > > > > > camera, but same xHCI controller.
> > > > > > > > > >
> > > > > > > > > > I have exactly the same issue with the xHCI controller of
> > > > > > > > > > my
> > > > > > > > > > laptop and
> > > > > > > > > > "Oculus Sensor" USB3 isochronous mostly-UVC cameras:
> > > > > > > > > >
> > > > > > > > > > 00:14.0 USB controller: Intel Corporation Wildcat Point-LP
> > > > > > > > > > USB
> > > > > > > > > > xHCI
> > > > > > > > > > Controller (rev 03) (prog-if 30 [XHCI])
> > > > > > > > > > Subsystem: Lenovo Wildcat Point-LP USB xHCI
> > > > > > > > > > Controller
> > > > > > > > > > Flags: bus master, medium devsel, latency 0, IRQ 44
> > > > > > > > > > Memory at f2220000 (64-bit, non-prefetchable)
> > > > > > > > > > [size=64K]
> > > > > > > > > > Capabilities: [70] Power Management version 2
> > > > > > > > > > Capabilities: [80] MSI: Enable+ Count=1/8 Maskable-
> > > > > > > > > > 64bit+
> > > > > > > > > > Kernel driver in use: xhci_hcd
> > > > > > > > > > Kernel modules: xhci_pci
> > > > > > > > > >
> > > > > > > > > > T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 4 Spd=5000
> > > > > > > > > > MxCh= 0
> > > > > > > > > > D: Ver= 3.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS= 9 #Cfgs= 1
> > > > > > > > > > P: Vendor=2833 ProdID=0211 Rev= 0.00
> > > > > > > > > > S: Manufacturer=Oculus VR
> > > > > > > > > > S: Product=Rift Sensor
> > > > > > > > > > S: SerialNumber=WMTD3034300BCT
> > > > > > > > > > C:* #Ifs= 2 Cfg#= 1 Atr=80 MxPwr=800mA
> > > > > > > > > > A: FirstIf#= 0 IfCount= 2 Cls=ff(vend.) Sub=03 Prot=00
> > > > > > > > > > I:* If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=01 Prot=00
> > > > > > > > > > Driver=uvcvideo
> > > > > > > > > > E: Ad=83(I) Atr=03(Int.) MxPS= 32 Ivl=128ms
> > > > > > > > > > I:* If#= 1 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=02 Prot=00
> > > > > > > > > > Driver=uvcvideo
> > > > > > > > > > I: If#= 1 Alt= 1 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=00
> > > > > > > > > > Driver=uvcvideo
> > > > > > > > > > E: Ad=81(I) Atr=05(Isoc) MxPS=1024 Ivl=125us
> > > > > > > > > > I: If#= 1 Alt= 2 #EPs= 1 Cls=ff(vend.) Sub=02 Prot=00
> > > > > > > > > > Driver=uvcvideo
> > > > > > > > > > E: Ad=81(I) Atr=05(Isoc) MxPS=1024 Ivl=125us
> > > > > > > > > >
> > > > > > > > > > Any USB2 or USB3 device that I plug in while the first
> > > > > > > > > > camera
> > > > > > > > > > is streaming in
> > > > > > > > > > altsetting 1 or 2 causes the bandwidth error. The same
> > > > > > > > > > happens
> > > > > > > > > > when I try to
> > > > > > > > > > change the altsetting on an isochronous endpoint of an
> > > > > > > > > > already
> > > > > > > > > > plugged device.
> > > > > > > > > > While the camera is in altsetting 0, other devices can be
> > > > > > > > > > probed and work.
> > > > > > > > > > > For some tests, I changed the
> > > > > > > > > > > xhci_change_max_exit_latency()
> > > > > > > > > > > function
> > > > > > > > > > > to ignore the requested MEL and set the MEL to 0. Now the
> > > > > > > > > > > USB
> > > > > > > > > > > devices
> > > > > > > > > > > are detected correctly.
> > > > > > > > > >
> > > > > > > > > > Exactly the same thing helps here, as well. With this hack,
> > > > > > > > > > streaming from two
> > > > > > > > > > of those cameras at the same time works without any
> > > > > > > > > > apparent
> > > > > > > > > > problem:
> > > > > > > > > >
> > > > > > > > > > ----------8<----------
> > > > > > > > > > diff --git a/drivers/usb/host/xhci.c
> > > > > > > > > > b/drivers/usb/host/xhci.c
> > > > > > > > > > index 297536c9fd00..3cb4a60d8822 100644
> > > > > > > > > > --- a/drivers/usb/host/xhci.c
> > > > > > > > > > +++ b/drivers/usb/host/xhci.c
> > > > > > > > > > @@ -4025,7 +4025,7 @@ static int __maybe_unused
> > > > > > > > > > xhci_change_max_exit_latency(struct xhci_hcd *xhci,
> > > > > > > > > > ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
> > > > > > > > > > slot_ctx = xhci_get_slot_ctx(xhci,
> > > > > > > > > > command->in_ctx);
> > > > > > > > > > slot_ctx->dev_info2 &= cpu_to_le32(~((u32)
> > > > > > > > > > MAX_EXIT));
> > > > > > > > > > - slot_ctx->dev_info2 |=
> > > > > > > > > > cpu_to_le32(max_exit_latency);
> > > > > > > > > > + slot_ctx->dev_info2 |= cpu_to_le32(0);
> > > > > > > > > > slot_ctx->dev_state = 0;
> > > > > > > > > >
> > > > > > > > > > xhci_dbg_trace(xhci,
> > > > > > > > > > trace_xhci_dbg_context_change,
> > > > > > > > > > ---------->8----------
> > > > > > > > >
> > > > > > > > > Ok, back after a week on sickleave.
> > > > > > > > > I'm getting the magewell capture device and try to reproduce
> > > > > > > > > this myself.
> > > > > > > >
> > > > > > > > I don't think that the issue is specific to the magewell capture
> > > > > > > > device, but rather should be reproducible with any USB3 device
> > > > > > > > with
> > > > > > > > isochronous endpoints.
> > > > > > > >
> > > > > > > > Anyway, please tell me, if I can somehow help you to get this
> > > > > > > > properly
> > > > > > > > fixed.
> > > > > > >
> > > > > > > I'm currently looking at device reset issues after suspend, but
> > > > > > > this is on the
> > > > > > > todo list.
> > > > > > >
> > > > > > > I got a magewell device, (haven't unboxed it yet)
> > > > > > > Maybe step by step instructions to reproduce it could speed
> > > > > > > things
> > > > > > > up.
> > > > > >
> > > > > > Did you have time to unbox and test the Magewell device?
> > > > >
> > > > > This seems to always get postponed due to other work,
> > > > >
> > > > > I just tried it out once today on a nearby laptop, gst-launch seems
> > > > > to work
> > > > > but couldn't reproduce the bandwidth issue when connecting a second
> > > > > usb device.
> > > > >
> > > > > But I haven't really tested it out properly yet.
> > > >
> > > > I just tested with 4.17-rc5 and the behavior remains the same. Is there
> > > > anything else I could do to get this fixed?
> > > >
> > >
> > > Briefed Zhengjun about this issue, one more brain on it.
> > > Adding him to the thread.
> > >
> >
> > Isochronous has been a problem for me for 2 years. I am using a rare 3D
> > stereo camera from Etron and had Isochronous problems and recently I
> > have discovered that the Logitech Brio also has what appears to be the
> > same issue. The Logitech Brio is the first Logitech USB3 camera that
> > uses Isochronous mode and you can do a search and find that linux users
> > are having problems with it.
>
> The Oculus Sensor devices contain Etron controllers as well (eSP770).
>
> > My suggestion would be for the USB3 team to order several Logitech Brio
> > cameras and debug the Isochronous problems. My company paid for someone
> > to try and debug the problem and we came up with a patch that we sent to
> > Mathias but it was not accepted because the change was not well
> > understood. I can probably buy cameras for Mathias if he is interested,
> > you only need 2 to get started, would like to see 5 or more running
> > simultaneously.
> >
> > The people at Etron also discovered that if you plug Isochronous cameras
> > into a hub with a Genesys Logic - GL3520 controller then it for some
> > reason masks the problem and allows multiple cameras to work.
> > Unfortunately this USB hub is extremely rare and I only found it in this
> > StarTech ST7300USBME hub. Also it doesn't work flawlessly but I have
> > tested it with 5 cameras.
> >
> > My all Intel motherboard and chipset machines work perfect with MS
> > Windows but not with Linux so it is hard to blame the hardware.
>
> Does anybody have new information about this issue? I tested last week
> on v5.2-rc5, and the issue still persists unchanged (and forcing MEL=0
> still helps).
>
> regards
> Philipp
FTR, Michael pointed out that 0472bf06c6fd ("xhci: Prevent U1/U2 link pm
states if exit latency is too long") solves the problem for him, but in
my case the ESIT < MEL checks do not trigger:
----------8<----------
From: Philipp Zabel <[email protected]>
Subject: [PATCH] HACK: usb: xhci: always set MEL to 0
This allows to stream from multiple Oculus Sensors simultaneously on a
Lenovo T450s.
Signed-off-by: Philipp Zabel <[email protected]>
---
Jun 26 08:24:25 ped kernel: usb 2-2: new SuperSpeed Gen 1 USB device number 3
using xhci_hcd
Jun 26 08:24:26 ped kernel: usb 2-2: New USB device found, idVendor=2833,
idProduct=0211, bcdDevice= 0.00
Jun 26 08:24:26 ped kernel: usb 2-2: New USB device strings: Mfr=1, Product=2,
SerialNumber=3
Jun 26 08:24:26 ped kernel: usb 2-2: Product: Rift Sensor
Jun 26 08:24:26 ped kernel: usb 2-2: Manufacturer: Oculus VR
Jun 26 08:24:26 ped kernel: usb 2-2: SerialNumber: WMTD3034300BCT
Jun 26 08:24:26 ped kernel: uvcvideo: Found UVC 1.00 device Rift Sensor
(2833:0211)
Jun 26 08:24:26 ped kernel: xhci_hcd 0000:00:14.0: add ep 0x83, slot id 5, new
drop flags = 0x0, new add flags = 0x80
Jun 26 08:24:26 ped kernel: xhci_hcd 0000:00:14.0: xhci_check_bandwidth called
for udev 00000000919e8856
Jun 26 08:24:26 ped kernel: usb 2-2: xhci_calculate_u1_timeout: service
interval = 128000000
Jun 26 08:24:26 ped kernel: usb 2-2: xhci_calculate_u1_timeout: max exit
latency = 10000
Jun 26 08:24:26 ped kernel: usb 2-2: Hub-initiated U1 disabled due to long
timeout 134400 ms
Jun 26 08:24:26 ped kernel: usb 2-2: xhci_change_max_exit_latency: MEL = 10 µs,
but using 0
Jun 26 08:24:26 ped kernel: usb 2-2: xhci_calculate_u2_timeout: service
interval = 128000000
Jun 26 08:24:26 ped kernel: usb 2-2: xhci_calculate_u2_timeout: max exit
latency = 512000
Jun 26 08:24:26 ped kernel: usb 2-2: Hub-initiated U2 disabled due to long
timeout 500 ms
Jun 26 08:24:26 ped kernel: usb 2-2: xhci_change_max_exit_latency: MEL = 512
µs, but using 0
---
drivers/usb/host/xhci.c | 12 +++++++++++-
1 file changed, 11 insertions(+), 1 deletion(-)
diff --git a/drivers/usb/host/xhci.c b/drivers/usb/host/xhci.c
index 3f79f35d0b19..ef26285eb7a6 100644
--- a/drivers/usb/host/xhci.c
+++ b/drivers/usb/host/xhci.c
@@ -4212,7 +4212,9 @@ static int __maybe_unused
xhci_change_max_exit_latency(struct xhci_hcd *xhci,
ctrl_ctx->add_flags |= cpu_to_le32(SLOT_FLAG);
slot_ctx = xhci_get_slot_ctx(xhci, command->in_ctx);
slot_ctx->dev_info2 &= cpu_to_le32(~((u32) MAX_EXIT));
- slot_ctx->dev_info2 |= cpu_to_le32(max_exit_latency);
+ dev_dbg(&udev->dev, "%s: MEL = %u µs, but using 0\n", __func__,
+ max_exit_latency);
+ slot_ctx->dev_info2 |= cpu_to_le32(0);
slot_ctx->dev_state = 0;
xhci_dbg_trace(xhci, trace_xhci_dbg_context_change,
@@ -4549,6 +4551,10 @@ static u16 xhci_calculate_u1_timeout(struct xhci_hcd
*xhci,
/* Prevent U1 if service interval is shorter than U1 exit latency */
if (usb_endpoint_xfer_int(desc) || usb_endpoint_xfer_isoc(desc)) {
+ dev_dbg(&udev->dev, "%s: service interval = %lu\n", __func__,
+ (unsigned long)xhci_service_interval_to_ns(desc));
+ dev_dbg(&udev->dev, "%s: max exit latency = %lu\n", __func__,
+ (unsigned long)udev->u1_params.mel);
if (xhci_service_interval_to_ns(desc) <= udev->u1_params.mel) {
dev_dbg(&udev->dev, "Disable U1, ESIT shorter than exit
latency\n");
return USB3_LPM_DISABLED;
@@ -4613,6 +4619,10 @@ static u16 xhci_calculate_u2_timeout(struct xhci_hcd
*xhci,
/* Prevent U2 if service interval is shorter than U2 exit latency */
if (usb_endpoint_xfer_int(desc) || usb_endpoint_xfer_isoc(desc)) {
+ dev_dbg(&udev->dev, "%s: service interval = %lu\n", __func__,
+ (unsigned long)xhci_service_interval_to_ns(desc));
+ dev_dbg(&udev->dev, "%s: max exit latency = %lu\n", __func__,
+ (unsigned long)udev->u2_params.mel);
if (xhci_service_interval_to_ns(desc) <= udev->u2_params.mel) {
dev_dbg(&udev->dev, "Disable U2, ESIT shorter than exit
latency\n");
return USB3_LPM_DISABLED;
--
2.20.1
---------->8----------
regards
Philipp
