Enable support for cbus gpios on FT232H. The cbus configuration is
stored in one word in the EEPROM at byte-offset 0x1a with the mux
config for ACBUS5, ACBUS6, ACBUS8 and ACBUS9 (only pins that can be
configured as I/O mode).
Tested using FT232H by configuring one ACBUS pin at a time.
Signed-off-by: Matthew Michilot <matthew.michi...@gmail.com>
Reviewed-by: Tim Harvey <thar...@gateworks.com>
---
V2:
- made hex notation all lowercase for consistency
- allocated 4 bytes instead of 2 bytes for buffer
- improved documentation on FT232H CBUS memory mapping
- fixed CBUS pins being incorrectly mapped to the wrong gpios
- sorted case labels alphabetically
---
drivers/usb/serial/ftdi_sio.c | 43 +++++++++++++++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/drivers/usb/serial/ftdi_sio.c b/drivers/usb/serial/ftdi_sio.c
index 4b3a049561f3..01e4ecccd079 100644
--- a/drivers/usb/serial/ftdi_sio.c
+++ b/drivers/usb/serial/ftdi_sio.c
@@ -2023,6 +2023,46 @@ static int ftdi_read_eeprom(struct usb_serial *serial,
void *dst, u16 addr,
return 0;
}
+static int ftdi_gpio_init_ft232h(struct usb_serial_port *port)
+{
+ struct ftdi_private *priv = usb_get_serial_port_data(port);
+ u8 *buf;
+ u16 cbus_config;
+ int ret;
+ int i;
+
+ buf = kmalloc(4, GFP_KERNEL);
+ if (!buf)
+ return -ENOMEM;
+
+ ret = ftdi_read_eeprom(port->serial, buf, 0x1a, 4);
+ if (ret < 0)
+ goto out_free;
+
+ /*
+ * FT232H CBUS Memory Map
+ *
+ * 0x1a: X- (upper nibble -> AC5)
+ * 0x1b: -X (lower nibble -> AC6)
+ * 0x1c: XX (upper nibble -> AC9 | lower nibble -> AC8)
+ */
+ cbus_config = buf[2] << 8 | (buf[1] & 0xf) << 4 | (buf[0] & 0xf0) >> 4;
+
+ priv->gc.ngpio = 4;
+ priv->gpio_altfunc = 0xff;
+
+ for (i = 0; i < priv->gc.ngpio; ++i) {
+ if ((cbus_config & 0xf) == FTDI_FTX_CBUS_MUX_GPIO)
+ priv->gpio_altfunc &= ~BIT(i);
+ cbus_config >>= 4;
+ }
+
+out_free:
+ kfree(buf);
+
+ return ret;
+}
+
static int ftdi_gpio_init_ft232r(struct usb_serial_port *port)
{
struct ftdi_private *priv = usb_get_serial_port_data(port);
@@ -2098,6 +2138,9 @@ static int ftdi_gpio_init(struct usb_serial_port *port)
int result;
switch (priv->chip_type) {
+ case FT232H:
+ result = ftdi_gpio_init_ft232h(port);
+ break;
case FT232RL:
result = ftdi_gpio_init_ft232r(port);
break;
--
2.17.1
