On Thu, 22 May 2014, Will Deacon wrote:
> Hi all,
>
> Although I don't think this is a new issue, booting mainline on my vexpress
> a9x4 (Quad ARMv7 Cortex-A9 board) with USB and PM_RUNTIME results in each
> CPU being constantly 20-50% loaded. A bit of investigation shows that this
> is due to the runtime-pm callbacks trying to autosuspend USB, despite this
5B> being unsupported by the host-controller (isp1760, which doesn't
have a
> ->bus_suspend callback). I've included a backtrace at the bottom of this mail.
>
> Anyway, since ->bus_suspend is not implemented, hcd_bus_suspend returns
> -ENOENT, which propagates back up to usb_runtime_suspend via usb_suspend_both.
> At this point, we override the return value with -EBUSY:
>
> drivers/usb/core/driver.c:usb_runtime_suspend:
>
> /* The PM core reacts badly unless the return code is 0,
> * -EAGAIN, or -EBUSY, so always return -EBUSY on an error.
> */
> if (status != 0)
> return -EBUSY;
>
> This then tells the runtime PM code to try again:
>
> drivers/base/power/runtime.c
>
> if (retval == -EAGAIN || retval == -EBUSY) {
> dev->power.runtime_error = 0;
>
> /*
> * If the callback routine failed an autosuspend, and
> * if the last_busy time has been updated so that there
> * is a new autosuspend expiration time, automatically
> * reschedule another autosuspend.
> */
> if ((rpmflags & RPM_AUTO) &&
> pm_runtime_autosuspend_expiration(dev) != 0)
> goto repeat;
>
> Consequently, I see a kworker thread on each CPU consuming a significant
> amount of the system resources. Worse, if I enable something like kmemleak
> (which adds more work to the failed suspend operation), I end up failing
> to boot entirely (NFS bombs out).
>
> Reverting db7c7c0aeef5 ("usb: Always return 0 or -EBUSY to the runtime
> PM core.") fixes this for me, but the commit log suggests that will break
> lsusb. That patch has also been in for three and a half years...
>
> Any ideas on how to fix this properly? In what ways does the PM core react
> badly to -ENOENT?
Okay, this is a bad problem.
The PM core takes any error response other than -EBUSY or -EAGAIN as an
indication that the device is in a runtime-PM error state. While that
is appropriate for a USB device, perhaps it's not so appropriate for a
USB host controller.
Anyway, there are two possible ways of handling this. One is to avoid
changing the error code to -EBUSY when the device in question is a root
hub. Just let it go into a runtime-PM error state; it won't matter
since the controller doesn't support runtime PM anyway. You can test
this by changing the "if (status != 0)" line in usb_runtime_suspend to
if (status != 0 && udev->parent)
The other approach is to disable runtime PM for the root hub when the
host controller driver doesn't have a bus_suspend or bus_resume method.
This seems like a cleaner approach; the patch below implements it.
Alan Stern
Index: usb-3.15/drivers/usb/core/hub.c
===================================================================
--- usb-3.15.orig/drivers/usb/core/hub.c
+++ usb-3.15/drivers/usb/core/hub.c
@@ -1703,8 +1703,19 @@ static int hub_probe(struct usb_interfac
*/
pm_runtime_set_autosuspend_delay(&hdev->dev, 0);
- /* Hubs have proper suspend/resume support. */
- usb_enable_autosuspend(hdev);
+ /*
+ * Hubs have proper suspend/resume support, except for root hubs
+ * where the controller driver doesn't have bus_suspend and
+ * bus_resume methods.
+ */
+ if (hdev->parent) { /* normal device */
+ usb_enable_autosuspend(hdev);
+ } else { /* root hub */
+ const struct hc_driver *drv = bus_to_hcd(hdev->bus)->driver;
+
+ if (drv->bus_suspend && drv->bus_resume)
+ usb_enable_autosuspend(hdev);
+ }
if (hdev->level == MAX_TOPO_LEVEL) {
dev_err(&intf->dev,
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
