Hello. On 12/17/2014 03:31 AM, Chanwoo Choi wrote:
MAX3355E chip integrates a charge pump and comparators to enable a system with an integrated USB OTG dual-role transceiver to function as a USB OTG dual-role device. In addition to sensing/controlling Vbus, the chip also passes thru the ID signal from the USB OTG connector. On some Renesas boards, this signal is just fed into the SoC thru a GPIO pin -- there's no real OTG controller, only host and gadget USB controllers sharing the same USB bus; however, we'd like to allow host or gadget drivers to be loaded depending on the cable type, hence the need for the MAX3355 extcon driver. The Vbus status signals are also wired to GPIOs (however, we're not currently intested in them), the OFFVBUS# signal is controlled by the host controllers, there's also the SHDN# signal wired to GPIO, which should be high for normal operation.
Signed-off-by: Sergei Shtylyov <sergei.shtyl...@cogentembedded.com>
--- The patch is against the 'extcon-next' branch of the 'extcon.git' repo.
Documentation/devicetree/bindings/extcon/extcon-max3355.txt | 21 ++ drivers/extcon/Kconfig | 6 drivers/extcon/Makefile | 1 drivers/extcon/extcon-max3355.c | 122 ++++++++++++ 4 files changed, 150 insertions(+)
Index: extcon/Documentation/devicetree/bindings/extcon/extcon-max3355.txt =================================================================== --- /dev/null +++ extcon/Documentation/devicetree/bindings/extcon/extcon-max3355.txt @@ -0,0 +1,21 @@ +MAX3355 USB OTG chip
Need manufactor information as following : -> Maxim MAX3355
Would be Maxim enough? Or perhaps I should use Maxim Integrated [Products]?
+-------------------- + +MAX3355 integrates a charge pump and comparators to enable a system with an +integrated USB OTG dual-role transceiver to function as a USB OTG dual-role +device. + +Required properties: +- compatible: should be "maxim,max3355"; +- maxim,shdn-gpio: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's SHDN# pin; +- maxim,id-gpio: should contain a phandle and GPIO specifier for the GPIO pin + connected to the MAX3355's ID_OUT pin. + +Example (Koelsch board): + + usb-otg { + compatible = "maxim,max3355"; + maxim,shdn-gpio = <&gpio2 4 GPIO_ACTIVE_LOW>; + maxim,id-gpio = <&gpio5 31 GPIO_ACTIVE_HIGH>;
Kernel already supported the gpio helper function to get gpio from devicetree. I prefer use follwoing style by using of_get_gpio()/of_get_gpio_flags() in include/linux/of_gpio.h.
gpios = <&gpio2 4 GPIO_ACTIVE_LOW>, <&gpio5 31 GPIO_ACTIVE_HIGH>;
OK, though Documentation/devicetree/bindings/gpio/gpio.txt does not seem to insist on using this one...
[...]
Index: extcon/drivers/extcon/extcon-max3355.c =================================================================== --- /dev/null +++ extcon/drivers/extcon/extcon-max3355.c @@ -0,0 +1,122 @@ +/* + * MAX3355 USB OTG chip extcon driver
ditto.
OK, though the other Maxim extcon drivers don't serve as a good example here...
[...]
+static irqreturn_t max3355_id_irq(int irq, void *dev_id) +{ + struct max3355_data *data = dev_id; + int id = gpio_get_value(data->id_gpio); + + extcon_set_cable_state(data->edev, "USB-HOST", !id);
You have to get the gpio flag in the devicetree by using of_get_gpio_flags() function and then you would set the cable state according to gpio state and flag.
I'm sorry but I just don't see why I have to do it. This is not a generic GPIO driver, and the polarities of the GPIOs are determined solely by the MAX3355 specs.
[...]
+static int max3355_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct max3355_data *data; + int gpio, irq, ret; + + data = devm_kzalloc(&pdev->dev, sizeof(struct max3355_data), + GFP_KERNEL); + if (!data) + return -ENOMEM; + + data->edev = devm_extcon_dev_allocate(&pdev->dev, max3355_cable); + if (IS_ERR(data->edev)) { + dev_err(&pdev->dev, "failed to allocate extcon device\n"); + return PTR_ERR(data->edev); + } + data->edev->name = kstrdup(np->name, GFP_KERNEL); + + gpio = of_get_named_gpio(np, "maxim,id-gpio", 0);
Use of_get_gpio() or of_get_gpio_flags().
OK, I'll use the first one.
"maxim,id-gpio" property has strong dependency on this driver and it is not standard.
I indented it to be Maxim specific. Not sure what using the standard property buys...
+ if (gpio < 0) + return gpio;
Need to add error message.
OK for all cases; extcon-gpio.c was probably a bad example... [...]
+ + ret = devm_gpio_request_one(&pdev->dev, gpio, GPIOF_DIR_OUT | + GPIOF_INIT_HIGH, pdev->name); + if (ret < 0) + return ret;
Need to add error message.
+ + ret = devm_gpio_request_one(&pdev->dev, data->id_gpio, GPIOF_DIR_IN, + pdev->name);
Why do you use same name for two gpio when devm_gpio_request_one? I prefer to use other name because two gpio is different.
And you're absolutely right here. Mindlessly copy-pasted the code from extcon-gpio.c...
[...]
+ + ret = devm_request_threaded_irq(&pdev->dev, irq, NULL, max3355_id_irq, + IRQF_TRIGGER_RISING | + IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
Is it right to add both RISING and FALLING trigger?
How else I'm supposed to know when the OTG ID signal goes low and high?
and need to add IRQF_NO_SUSPEND to wakeup from suspend state when interrupt happen.
Hm, are you sure we want to wake up on plugging another kind of USB cable? [...]
+static struct platform_driver max3355_driver = { + .probe = max3355_probe, + .driver = { + .name = "extcon-max3355", + .of_match_table = max3355_match_table, + .owner = THIS_MODULE, + }, +}; + +module_platform_driver(max3355_driver); +
Don't need un-used blank line.
I don't understand. There's empty line in such case in extcon-gpio.c...
+MODULE_AUTHOR("Sergei Shtylyov <sergei.shtyl...@cogentembedded.com>"); +MODULE_DESCRIPTION("MAX3355 extcon driver");
Maxim MAX3355.
OK, seeing it in the other Maxim drivers.
+MODULE_LICENSE("GPL v2");
Thanks, Chanwoo Choi
WBR, Sergei -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html