Good question. The cmd line option is a tri-state: (no command line option) -> force_rs485=-1 -> auto-detect based on product ID force_rs485 = 0 -> never set RS485 mode (regardless of product ID) force_rs485 = 1 -> always set RS485 mode (regardless of product ID)
> On Mar 1, 2016, at 11:38 AM, Sergei Shtylyov
> <sergei.shtyl...@cogentembedded.com> wrote:
>
> Hello.
>
> On 03/01/2016 08:54 PM, amarb...@apl.washington.edu wrote:
>
>> From: Aaron Marburg <amarb...@apl.washington.edu>
>>
>> The USOPTL4-4P and USOPTL4-2P USB-to-quad/dual RS-485/422 hubs use the
>> Moschip 7840/7820. For correct operation in RS-485, the chip must be
>> configured in “RS-485 mode” through the scratchpad register as per the
>> datasheet. This strobes the DTR line on transmission, enabling the driver
>> on the RS485 transceiver chip.
>>
>> Patch enables RS485 mode automatically for the USOPTL4-4P and USOPTL4-2P
>> based on USB product ID. It also includes a module command line option
>> "force_rs485={0|1}" to manually force-enable (for all devices regardless
>> of USB ID) and force-disable (for no devices, not even USOPTL*) the
>> functionality.
>>
>> Signed-off-by: Aaron Marburg <amarb...@apl.washington.edu>
>>
>> ---
>> drivers/usb/serial/mos7840.c | 25 +++++++++++++++++++++++++
>> 1 file changed, 25 insertions(+)
>>
>> diff --git a/drivers/usb/serial/mos7840.c b/drivers/usb/serial/mos7840.c
>> index 2c69bfc..2356828 100644
>> --- a/drivers/usb/serial/mos7840.c
>> +++ b/drivers/usb/serial/mos7840.c
>> @@ -182,6 +182,9 @@
>> #define LED_ON_MS 500
>> #define LED_OFF_MS 500
>>
>> +/* Command-line option to force RS485 mode */
>> +static int force_rs485 = -1;
>
> Why not just 0 (and no initializer)?
>
>> +
>> enum mos7840_flag {
>> MOS7840_FLAG_CTRL_BUSY,
>> MOS7840_FLAG_LED_BUSY,
> [...]
>> @@ -991,6 +997,22 @@ static int mos7840_open(struct tty_struct *tty, struct
>> usb_serial_port *port)
>> status = mos7840_set_uart_reg(port, LINE_CONTROL_REGISTER, Data);
>> mos7840_port->shadowLCR = Data;
>>
>> + if (!(force_rs485 == 0)) {
>
> Use != please. Or better still, just *if* (force).
Yes, of course this would be simpler.
>
>> + if ((force_rs485 == 1) ||
>> + (product == BANDB_DEVICE_ID_USOPTL4_4P) ||
>> + (product == BANDB_DEVICE_ID_USOPTL4_2P)) {
>> + /* Enable RS485 mode by setting bytes in
>> + * scratchpad register:
>> + * 0x00 RS485 mode disabled
>> + * 0x80 = RS485 mode enabled, DTR Low on tx
>> + * 0xC0 = RS485 mode enabled, DTR High on tx
>> + */
>> + dev_notice(&port->dev, "Detected B&B Electronics
>> USOPTL4_4P, enabling RS485 mode.\n");
>> + Data = 0xC0;
>> + status = mos7840_set_uart_reg(port,
>> SCRATCH_PAD_REGISTER, Data);
>> + }
>> + }
>> +
>> /* clearing Bulkin and Bulkout Fifo */
>> Data = 0x0;
>> status = mos7840_get_reg_sync(port, mos7840_port->SpRegOffset, &Data);
>> @@ -2403,5 +2425,8 @@ static struct usb_serial_driver * const
>> serial_drivers[] = {
>>
>> module_usb_serial_driver(serial_drivers, id_table);
>>
>> +module_param(force_rs485, int, S_IRUGO);
>> +MODULE_PARM_DESC(force_rs845, "Force RS-485 mode (1 = force enable, 0 =
>> force enable).
>
> Both 0 and 1 enable? :-)
You are correct, should be 0 = force disable.
>
>> Otherwise automatically enabled for B&B Elec. USOPTL4-4P and USOPTL4-2P.");
>> +
>> MODULE_DESCRIPTION(DRIVER_DESC);
>> MODULE_LICENSE("GPL");
>> -
>
> [...]
>
> MBR, Sergei
smime.p7s
Description: S/MIME cryptographic signature
