The usb driver can now take a regulator instead of the platform
callbacks for vbus handling. Lets use a regulator so we can remove
the callbacks in a later patch.
Signed-off-by: Axel Haslam <ahas...@baylibre.com>
---
arch/arm/mach-davinci/board-da830-evm.c | 108 +++++++++++---------------------
1 file changed, 38 insertions(+), 70 deletions(-)
diff --git a/arch/arm/mach-davinci/board-da830-evm.c
b/arch/arm/mach-davinci/board-da830-evm.c
index 5db0901..16a401a 100644
--- a/arch/arm/mach-davinci/board-da830-evm.c
+++ b/arch/arm/mach-davinci/board-da830-evm.c
@@ -14,6 +14,7 @@
#include <linux/console.h>
#include <linux/interrupt.h>
#include <linux/gpio.h>
+#include <linux/gpio/machine.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/i2c/pcf857x.h>
@@ -28,6 +29,7 @@
#include <linux/platform_data/spi-davinci.h>
#include <linux/platform_data/usb-davinci.h>
#include <linux/regulator/machine.h>
+#include <linux/regulator/fixed.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
@@ -38,72 +40,48 @@
#include <mach/da8xx.h>
#define DA830_EVM_PHY_ID ""
-/*
- * USB1 VBUS is controlled by GPIO1[15], over-current is reported on GPIO2[4].
- */
-#define ON_BD_USB_DRV GPIO_TO_PIN(1, 15)
-#define ON_BD_USB_OVC GPIO_TO_PIN(2, 4)
static const short da830_evm_usb11_pins[] = {
DA830_GPIO1_15, DA830_GPIO2_4,
-1
};
-static da8xx_ocic_handler_t da830_evm_usb_ocic_handler;
-
-static int da830_evm_usb_set_power(unsigned port, int on)
-{
- gpio_set_value(ON_BD_USB_DRV, on);
- return 0;
-}
+static struct regulator_consumer_supply usb_ohci_consumer_supply =
+ REGULATOR_SUPPLY("vbus", "ohci-da8xx");
-static int da830_evm_usb_get_power(unsigned port)
-{
- return gpio_get_value(ON_BD_USB_DRV);
-}
-
-static int da830_evm_usb_get_oci(unsigned port)
-{
- return !gpio_get_value(ON_BD_USB_OVC);
-}
-
-static irqreturn_t da830_evm_usb_ocic_irq(int, void *);
-
-static int da830_evm_usb_ocic_notify(da8xx_ocic_handler_t handler)
-{
- int irq = gpio_to_irq(ON_BD_USB_OVC);
- int error = 0;
-
- if (handler != NULL) {
- da830_evm_usb_ocic_handler = handler;
-
- error = request_irq(irq, da830_evm_usb_ocic_irq,
- IRQF_TRIGGER_RISING | IRQF_TRIGGER_FALLING,
- "OHCI over-current indicator", NULL);
- if (error)
- pr_err("%s: could not request IRQ to watch over-current
indicator changes\n",
- __func__);
- } else
- free_irq(irq, NULL);
-
- return error;
-}
+static struct regulator_init_data usb_ohci_initdata = {
+ .consumer_supplies = &usb_ohci_consumer_supply,
+ .num_consumer_supplies = 1,
+ .constraints = {
+ .valid_ops_mask = REGULATOR_CHANGE_STATUS,
+ },
+};
-static struct da8xx_ohci_root_hub da830_evm_usb11_pdata = {
- .set_power = da830_evm_usb_set_power,
- .get_power = da830_evm_usb_get_power,
- .get_oci = da830_evm_usb_get_oci,
- .ocic_notify = da830_evm_usb_ocic_notify,
+static struct fixed_voltage_config usb_ohci_config = {
+ .supply_name = "vbus",
+ .microvolts = 5000000,
+ .gpio = GPIO_TO_PIN(1, 15),
+ .enable_high = 1,
+ .enabled_at_boot = 0,
+ .init_data = &usb_ohci_initdata,
+};
- /* TPS2065 switch @ 5V */
- .potpgt = (3 + 1) / 2, /* 3 ms max */
+static struct platform_device da8xx_usb11_regulator = {
+ .name = "reg-fixed-voltage",
+ .id = 0,
+ .dev = {
+ .platform_data = &usb_ohci_config,
+ },
};
-static irqreturn_t da830_evm_usb_ocic_irq(int irq, void *dev_id)
-{
- da830_evm_usb_ocic_handler(&da830_evm_usb11_pdata, 1);
- return IRQ_HANDLED;
-}
+static struct gpiod_lookup_table usb11_gpios_table = {
+ .dev_id = "reg-fixed-voltage.0",
+ .table = {
+ /* gpio chip 1 contains gpio range 32-63 */
+ GPIO_LOOKUP("davinci_gpio.1", 4, "over-current",
+ GPIO_ACTIVE_LOW),
+ },
+};
static __init void da830_evm_usb_init(void)
{
@@ -145,23 +123,13 @@ static __init void da830_evm_usb_init(void)
return;
}
- ret = gpio_request(ON_BD_USB_DRV, "ON_BD_USB_DRV");
- if (ret) {
- pr_err("%s: failed to request GPIO for USB 1.1 port power
control: %d\n",
- __func__, ret);
- return;
- }
- gpio_direction_output(ON_BD_USB_DRV, 0);
+ gpiod_add_lookup_table(&usb11_gpios_table);
- ret = gpio_request(ON_BD_USB_OVC, "ON_BD_USB_OVC");
- if (ret) {
- pr_err("%s: failed to request GPIO for USB 1.1 port
over-current indicator: %d\n",
- __func__, ret);
- return;
- }
- gpio_direction_input(ON_BD_USB_OVC);
+ ret = platform_device_register(&da8xx_usb11_regulator);
+ if (ret)
+ pr_warn("fail to add ohci regulator\n");
- ret = da8xx_register_usb11(&da830_evm_usb11_pdata);
+ ret = da8xx_register_usb11(NULL);
if (ret)
pr_warn("%s: USB 1.1 registration failed: %d\n", __func__, ret);
}
--
2.10.1
--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
