Hi, Baolin Wang <baolin.w...@linaro.org> writes: > When dwc3 controller acts as host role with attaching slow speed device > (like mouse or keypad). Then if we plugged out the slow speed device, > it will timeout to run the deconfiguration endpoint command to drop the > endpoint's resources. Some xHCI command timeout log as below when > disconnecting one slow device: > > [ 99.807739] c0 xhci-hcd.0.auto: Port Status Change Event for port 1 > [ 99.814699] c0 xhci-hcd.0.auto: resume root hub > [ 99.819992] c0 xhci-hcd.0.auto: handle_port_status: starting port > polling. > [ 99.827808] c0 xhci-hcd.0.auto: get port status, actual port 0 status > = 0x202a0 > [ 99.835903] c0 xhci-hcd.0.auto: Get port status returned 0x10100 > [ 99.850052] c0 xhci-hcd.0.auto: clear port connect change, actual > port 0 status = 0x2a0 > [ 99.859313] c0 xhci-hcd.0.auto: Cancel URB ffffffc01ed6cd00, dev 1, > ep 0x81, starting at offset 0xc406d210 > [ 99.869645] c0 xhci-hcd.0.auto: // Ding dong! > [ 99.874776] c0 xhci-hcd.0.auto: Stopped on Transfer TRB > [ 99.880713] c0 xhci-hcd.0.auto: Removing canceled TD starting at > 0xc406d210 (dma). > [ 99.889012] c0 xhci-hcd.0.auto: Finding endpoint context > [ 99.895069] c0 xhci-hcd.0.auto: Cycle state = 0x1 > [ 99.900519] c0 xhci-hcd.0.auto: New dequeue segment = > ffffffc1112f0880 (virtual) > [ 99.908655] c0 xhci-hcd.0.auto: New dequeue pointer = 0xc406d220 (DMA) > [ 99.915927] c0 xhci-hcd.0.auto: Set TR Deq Ptr cmd, new deq seg = > ffffffc1112f0880 (0xc406d000 dma), > new deq ptr = ffffff8002175220 > (0xc406d220 dma), new cycle = 1 > [ 99.931242] c0 xhci-hcd.0.auto: // Ding dong! > [ 99.936360] c0 xhci-hcd.0.auto: Successful Set TR Deq Ptr cmd, > deq = @c406d220 > [ 99.944458] c0 xhci-hcd.0.auto: xhci_hub_status_data: stopping port > polling. > [ 100.047619] c0 xhci-hcd.0.auto: xhci_drop_endpoint called for udev > ffffffc01ae08800 > [ 100.057002] c0 xhci-hcd.0.auto: drop ep 0x81, slot id 1, new drop > flags = 0x8, new add flags = 0x0 > [ 100.067878] c0 xhci-hcd.0.auto: xhci_check_bandwidth called for udev > ffffffc01ae08800 > [ 100.076868] c0 xhci-hcd.0.auto: New Input Control Context: > > ...... > > [ 100.427252] c0 xhci-hcd.0.auto: // Ding dong! > [ 105.430728] c0 xhci-hcd.0.auto: Command timeout > [ 105.436029] c0 xhci-hcd.0.auto: Abort command ring > [ 113.558223] c0 xhci-hcd.0.auto: Command completion event does not match > command > [ 113.569778] c0 xhci-hcd.0.auto: Timeout while waiting for configure > endpoint command > > The reason is it will suspend USB phy to disable phy clock when > disconnecting the slow USB decice, that will hang on the xHCI commands > executing which depends on the phy clock. > > Thus we should disable USB2.0 phy suspend feature when dwc3 acts as host > role. > > Signed-off-by: Baolin Wang <baolin.w...@linaro.org> > --- > drivers/usb/dwc3/core.c | 14 ++++++++++++++ > 1 file changed, 14 insertions(+) > > diff --git a/drivers/usb/dwc3/core.c b/drivers/usb/dwc3/core.c > index 9a4a5e4..0b646cf 100644 > --- a/drivers/usb/dwc3/core.c > +++ b/drivers/usb/dwc3/core.c > @@ -565,6 +565,20 @@ static int dwc3_phy_setup(struct dwc3 *dwc) > if (dwc->revision > DWC3_REVISION_194A) > reg |= DWC3_GUSB2PHYCFG_SUSPHY; > > + /* > + * When dwc3 controller acts as host role with attaching one slow speed > + * device (like mouse or keypad). Then if we plugged out the slow speed > + * device, it will timeout to run the deconfiguration endpoint command. > + * The reason is it will suspend USB phy to disable phy clock when > + * disconnecting slow speed decice, which will affect the xHCI commands > + * executing. > + * > + * Thus we should disable USB 2.0 phy suspend feature when dwc3 acts as > + * host role. > + */ > + if (dwc->dr_mode == USB_DR_MODE_HOST || dwc->dr_mode == USB_DR_MODE_OTG) > + reg &= ~DWC3_GUSB2PHYCFG_SUSPHY;
which version of the core you're using? Recent version (since 1.94A, IIRC) can manage core suspend automatically. Also, this patch of yours will cause a power consumption regression. -- balbi
signature.asc
Description: PGP signature
