The adaptor can be found on development boards for 78k, RL78 and V850 microcontrollers produced by Renesas Electronics Corporation.
This is not a full-featured USB to serial converter, however it allows basic communication and simple control which is enough for programming of on-board flash and debugging through a debug monitor. uPD78F0730 is a USB-enabled microcontroller with USB-to-UART conversion implemented in firmware. This chip is also present in some debugging adaptors which use it for USB-to-SPI conversion as well. The present driver doesn't cover SPI, only USB-to-UART conversion is supported. Signed-off-by: Maksim Salau <maksim.sa...@gmail.com> --- PATCH v2 can be found here: http://thread.gmane.org/gmane.linux.usb.general/137999 Changes from v2: * Addressed all comments * Dropped inversion of DTR and RTS signals * Removed support of software flow control and added hardware flow control (Both are untested) The device I have have only one output signal that is toggled by tiocmset(fd, TIOCM_DTR, 0) and tiocmset(fd, TIOCM_RTS, 0). Thanks, Maksim. drivers/usb/serial/Kconfig | 9 + drivers/usb/serial/Makefile | 1 + drivers/usb/serial/upd78f0730.c | 445 ++++++++++++++++++++++++++++++++++++++++ 3 files changed, 455 insertions(+) create mode 100644 drivers/usb/serial/upd78f0730.c diff --git a/drivers/usb/serial/Kconfig b/drivers/usb/serial/Kconfig index 56ecb8b..311d1cf 100644 --- a/drivers/usb/serial/Kconfig +++ b/drivers/usb/serial/Kconfig @@ -703,6 +703,15 @@ config USB_SERIAL_QT2 To compile this driver as a module, choose M here: the module will be called quatech-serial. +config USB_SERIAL_UPD78F0730 + tristate "USB Renesas uPD78F0730 Single Port Serial Driver" + help + Say Y here if you want to use the Renesas uPD78F0730 + serial driver. + + To compile this driver as a module, choose M here: the + module will be called upd78f0730. + config USB_SERIAL_DEBUG tristate "USB Debugging Device" help diff --git a/drivers/usb/serial/Makefile b/drivers/usb/serial/Makefile index 349d9df..93fc707 100644 --- a/drivers/usb/serial/Makefile +++ b/drivers/usb/serial/Makefile @@ -60,3 +60,4 @@ obj-$(CONFIG_USB_SERIAL_WISHBONE) += wishbone-serial.o obj-$(CONFIG_USB_SERIAL_WHITEHEAT) += whiteheat.o obj-$(CONFIG_USB_SERIAL_XIRCOM) += keyspan_pda.o obj-$(CONFIG_USB_SERIAL_XSENS_MT) += xsens_mt.o +obj-$(CONFIG_USB_SERIAL_UPD78F0730) += upd78f0730.o diff --git a/drivers/usb/serial/upd78f0730.c b/drivers/usb/serial/upd78f0730.c new file mode 100644 index 0000000..e2bed13 --- /dev/null +++ b/drivers/usb/serial/upd78f0730.c @@ -0,0 +1,445 @@ +/* + * Renesas Electronics uPD78F0730 USB to serial converter driver + * + * Copyright (C) 2014,2016 Maksim Salau <maksim.sa...@gmail.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 + * as published by the Free Software Foundation. + * + * Protocol of the adaptor is described in the application note U19660EJ1V0AN00 + * μPD78F0730 8-bit Single-Chip Microcontroller + * USB-to-Serial Conversion Software + * <https://www.renesas.com/en-eu/doc/DocumentServer/026/U19660EJ1V0AN00.pdf> + * + * The adaptor functionality is limited to the following: + * - data bits: 7 or 8 + * - stop bits: 1 or 2 + * - parity: even, odd or none + * - flow control: hardware or none + * - baud rates: 2400, 4800, 9600, 19200, 38400, 57600, 115200 + * - signals: DTS, RTS and BREAK + * - there is an option to enable parity error character substitution, + * but is not supported by the driver + * - XON/XOFF flow control is described in the document, + * but is not supported by the driver + */ + +#include <linux/kernel.h> +#include <linux/string.h> +#include <linux/module.h> +#include <linux/slab.h> +#include <linux/spinlock.h> +#include <linux/tty.h> +#include <linux/usb.h> +#include <linux/usb/serial.h> + +#define DRIVER_DESC "Renesas uPD78F0730 USB to serial converter driver" + +#define DRIVER_AUTHOR "Maksim Salau <maksim.sa...@gmail.com>" + +static const struct usb_device_id id_table[] = { + { USB_DEVICE(0x045B, 0x0212) }, /* YRPBRL78G13, YRPBRL78G14 */ + { USB_DEVICE(0x0409, 0x0063) }, /* V850ESJX3-STICK */ + {} +}; + +MODULE_DEVICE_TABLE(usb, id_table); + +/* + * Private data structure type declaration. + * Each adaptor is associated with a private structure, that holds the current + * state of control signals (DTR, RTS and BREAK). + */ +struct upd78f0730_serial_private { + struct mutex lock; /* mutex to protect line_signals */ + u8 line_signals; +}; + +/* Op-codes of control commands */ +#define UPD78F0730_CMD_LINE_CONTROL 0x00 +#define UPD78F0730_CMD_SET_DTR_RTS 0x01 +#define UPD78F0730_CMD_SET_XON_XOFF_CHR 0x02 +#define UPD78F0730_CMD_OPEN_CLOSE 0x03 +#define UPD78F0730_CMD_SET_ERR_CHR 0x04 + +/* Data sizes in UPD78F0730_CMD_LINE_CONTROL command */ +#define UPD78F0730_DATA_SIZE_7_BITS 0x00 +#define UPD78F0730_DATA_SIZE_8_BITS 0x01 +#define UPD78F0730_DATA_SIZE_MASK 0x01 + +/* Stop-bit modes in UPD78F0730_CMD_LINE_CONTROL command */ +#define UPD78F0730_STOP_BIT_1_BIT 0x00 +#define UPD78F0730_STOP_BIT_2_BIT 0x02 +#define UPD78F0730_STOP_BIT_MASK 0x02 + +/* Parity modes in UPD78F0730_CMD_LINE_CONTROL command */ +#define UPD78F0730_PARITY_NONE 0x00 +#define UPD78F0730_PARITY_EVEN 0x04 +#define UPD78F0730_PARITY_ODD 0x08 +#define UPD78F0730_PARITY_MASK 0x0C + +/* Flow control modes in UPD78F0730_CMD_LINE_CONTROL command */ +#define UPD78F0730_FLOW_CONTROL_NONE 0x00 +#define UPD78F0730_FLOW_CONTROL_HW 0x10 +#define UPD78F0730_FLOW_CONTROL_SW 0x20 +#define UPD78F0730_FLOW_CONTROL_MASK 0x30 + +/* Control signal bits in UPD78F0730_CMD_SET_DTR_RTS command */ +#define UPD78F0730_RTS 0x01 +#define UPD78F0730_DTR 0x02 +#define UPD78F0730_BREAK 0x04 + +/* Port modes in UPD78F0730_CMD_OPEN_CLOSE command */ +#define UPD78F0730_PORT_CLOSE 0x00 +#define UPD78F0730_PORT_OPEN 0x01 + +/* Error character substitution modes in UPD78F0730_CMD_SET_ERR_CHR command */ +#define UPD78F0730_ERR_CHR_DISABLED 0x00 +#define UPD78F0730_ERR_CHR_ENABLED 0x01 + +/* + * Declaration of command structures + */ + +/* UPD78F0730_CMD_LINE_CONTROL command */ +struct line_control { + u8 opcode; + __le32 baud_rate; + u8 params; +} __packed; + +/* UPD78F0730_CMD_SET_DTR_RTS command */ +struct set_dtr_rts { + u8 opcode; + u8 params; +}; + +/* UPD78F0730_CMD_SET_XON_OFF_CHR command */ +struct set_xon_xoff_chr { + u8 opcode; + u8 xon; + u8 xoff; +}; + +/* UPD78F0730_CMD_OPEN_CLOSE command */ +struct open_close { + u8 opcode; + u8 state; +}; + +/* UPD78F0730_CMD_SET_ERR_CHR command */ +struct set_err_chr { + u8 opcode; + u8 state; + u8 err_char; +}; + +static int upd78f0730_send_ctl(struct usb_serial_port *port, + void *data, int size) +{ + int res; + struct device *dev = &port->dev; + struct usb_device *usbdev = port->serial->dev; + void *buf; + + if (!size) + return 0; + if (!data) { + dev_err(dev, "invalid arguments\n"); + return -EINVAL; + } + + buf = kmemdup(data, size, GFP_KERNEL); + + if (!buf) + return -ENOMEM; + + res = usb_control_msg(usbdev, usb_sndctrlpipe(usbdev, 0), 0x00, + USB_TYPE_VENDOR | USB_RECIP_DEVICE | USB_DIR_OUT, + 0x0000, 0x0000, buf, size, USB_CTRL_SET_TIMEOUT); + + kfree(buf); + + if (res < 0 || res != size) { + dev_err(dev, "send failed: opcode=%02x, size=%d, res=%d\n", + *(u8 *)data, size, res); + /* The maximum expected length of a transfer is 6 bytes */ + return -EIO; + } + + return 0; +} + +static int upd78f0730_port_probe(struct usb_serial_port *port) +{ + struct upd78f0730_serial_private *private; + + private = kzalloc(sizeof(*private), GFP_KERNEL); + if (!private) + return -ENOMEM; + mutex_init(&private->lock); + private->line_signals = 0; + usb_set_serial_port_data(port, private); + return 0; +} + +static int upd78f0730_port_remove(struct usb_serial_port *port) +{ + struct upd78f0730_serial_private *private; + + private = usb_get_serial_port_data(port); + mutex_destroy(&private->lock); + kfree(private); + return 0; +} + +static int upd78f0730_tiocmget(struct tty_struct *tty) +{ + int res = 0; + int signals; + struct device *dev = tty->dev; + struct upd78f0730_serial_private *private; + struct usb_serial_port *port = tty->driver_data; + + private = usb_get_serial_port_data(port); + + mutex_lock(&private->lock); + signals = private->line_signals; + mutex_unlock(&private->lock); + + res = ((signals & UPD78F0730_DTR) ? TIOCM_DTR : 0) | + ((signals & UPD78F0730_RTS) ? TIOCM_RTS : 0); + + dev_dbg(dev, "res = %x\n", res); + + return res; +} + +static int upd78f0730_tiocmset(struct tty_struct *tty, + unsigned int set, unsigned int clear) +{ + int res; + struct device *dev = tty->dev; + struct upd78f0730_serial_private *private; + struct usb_serial_port *port = tty->driver_data; + struct set_dtr_rts request = { .opcode = UPD78F0730_CMD_SET_DTR_RTS }; + + private = usb_get_serial_port_data(port); + + mutex_lock(&private->lock); + if (set & TIOCM_DTR) { + private->line_signals |= UPD78F0730_DTR; + dev_dbg(dev, "set DTR\n"); + } + if (set & TIOCM_RTS) { + private->line_signals |= UPD78F0730_RTS; + dev_dbg(dev, "set RTS\n"); + } + if (clear & TIOCM_DTR) { + private->line_signals &= ~UPD78F0730_DTR; + dev_dbg(dev, "reset DTR\n"); + } + if (clear & TIOCM_RTS) { + private->line_signals &= ~UPD78F0730_RTS; + dev_dbg(dev, "reset RTS\n"); + } + request.params = private->line_signals; + + res = upd78f0730_send_ctl(port, &request, sizeof(request)); + mutex_unlock(&private->lock); + + return res; +} + +static void upd78f0730_break_ctl(struct tty_struct *tty, int break_state) +{ + struct device *dev = tty->dev; + struct upd78f0730_serial_private *private; + struct usb_serial_port *port = tty->driver_data; + struct set_dtr_rts request = { .opcode = UPD78F0730_CMD_SET_DTR_RTS }; + + private = usb_get_serial_port_data(port); + + mutex_lock(&private->lock); + if (break_state) { + private->line_signals |= UPD78F0730_BREAK; + dev_dbg(dev, "set BREAK\n"); + } else { + private->line_signals &= ~UPD78F0730_BREAK; + dev_dbg(dev, "reset BREAK\n"); + } + request.params = private->line_signals; + + upd78f0730_send_ctl(port, &request, sizeof(request)); + mutex_unlock(&private->lock); +} + +static void upd78f0730_dtr_rts(struct usb_serial_port *port, int on) +{ + struct tty_struct *tty = port->port.tty; + unsigned int set = 0; + unsigned int clear = 0; + + if (on) + set = TIOCM_DTR | TIOCM_RTS; + else + clear = TIOCM_DTR | TIOCM_RTS; + + upd78f0730_tiocmset(tty, set, clear); +} + +static speed_t upd78f0730_get_baud_rate(struct tty_struct *tty) +{ + int i; + const tcflag_t baud_rate = C_BAUD(tty); + const tcflag_t supported[] = {B2400, B4800, B9600, + B19200, B38400, B57600, B115200}; + + for (i = ARRAY_SIZE(supported) - 1; i >= 0; i--) { + if (baud_rate == supported[i]) + return tty_get_baud_rate(tty); + } + + /* If the baud rate is not supported, switch to the default baud rate */ + tty->termios.c_cflag &= ~CBAUD; + tty->termios.c_cflag |= B9600; + + return tty_get_baud_rate(tty); +} + +static void upd78f0730_set_termios(struct tty_struct *tty, + struct usb_serial_port *port, + struct ktermios *old_termios) +{ + struct device *dev = &port->dev; + struct line_control request_control; + speed_t baud_rate; + + if (old_termios && !tty_termios_hw_change(&tty->termios, old_termios)) + return; + + if (C_BAUD(tty) == B0) + upd78f0730_dtr_rts(port, 0); + + baud_rate = upd78f0730_get_baud_rate(tty); + request_control.opcode = UPD78F0730_CMD_LINE_CONTROL; + request_control.baud_rate = cpu_to_le32(baud_rate); + request_control.params = 0; + dev_dbg(dev, "baud rate = %d\n", baud_rate); + + switch (C_CSIZE(tty)) { + case CS7: + request_control.params |= UPD78F0730_DATA_SIZE_7_BITS; + dev_dbg(dev, "7 data bits\n"); + break; + default: + tty->termios.c_cflag &= ~CSIZE; + tty->termios.c_cflag |= CS8; + dev_warn(dev, "data size is not supported, using 8 bits\n"); + /* fall through */ + case CS8: + request_control.params |= UPD78F0730_DATA_SIZE_8_BITS; + dev_dbg(dev, "8 data bits\n"); + break; + } + + if (C_PARENB(tty)) { + if (C_PARODD(tty)) { + request_control.params |= UPD78F0730_PARITY_ODD; + dev_dbg(dev, "odd parity\n"); + } else { + request_control.params |= UPD78F0730_PARITY_EVEN; + dev_dbg(dev, "even parity\n"); + } + + if (C_CMSPAR(tty)) { + tty->termios.c_cflag &= ~CMSPAR; + dev_warn(dev, "MARK/SPACE parity is not supported\n"); + } + } else { + request_control.params |= UPD78F0730_PARITY_NONE; + dev_dbg(dev, "no parity\n"); + } + + if (C_CSTOPB(tty)) { + request_control.params |= UPD78F0730_STOP_BIT_2_BIT; + dev_dbg(dev, "2 stop bits\n"); + } else { + request_control.params |= UPD78F0730_STOP_BIT_1_BIT; + dev_dbg(dev, "1 stop bit\n"); + } + + if (C_CRTSCTS(tty)) { + request_control.params |= UPD78F0730_FLOW_CONTROL_HW; + dev_dbg(dev, "hardware flow control\n"); + } else { + request_control.params |= UPD78F0730_FLOW_CONTROL_NONE; + dev_dbg(dev, "no flow control\n"); + } + + if (I_IXOFF(tty) || I_IXON(tty)) { + tty->termios.c_iflag &= ~(IXOFF | IXON); + dev_warn(dev, "software flow control is not supported\n"); + } + + upd78f0730_send_ctl(port, &request_control, sizeof(request_control)); +} + +static int upd78f0730_open(struct tty_struct *tty, struct usb_serial_port *port) +{ + int res; + struct open_close request_open = { + .opcode = UPD78F0730_CMD_OPEN_CLOSE, + .state = UPD78F0730_PORT_OPEN + }; + + res = upd78f0730_send_ctl(port, &request_open, sizeof(request_open)); + if (res) + return res; + + if (tty) + upd78f0730_set_termios(tty, port, NULL); + + return usb_serial_generic_open(tty, port); +} + +static void upd78f0730_close(struct usb_serial_port *port) +{ + struct open_close request_close = { + .opcode = UPD78F0730_CMD_OPEN_CLOSE, + .state = UPD78F0730_PORT_CLOSE + }; + + usb_serial_generic_close(port); + upd78f0730_send_ctl(port, &request_close, sizeof(request_close)); +} + +static struct usb_serial_driver upd78f0730_device = { + .driver = { + .owner = THIS_MODULE, + .name = "upd78f0730", + }, + .id_table = id_table, + .num_ports = 1, + .port_probe = upd78f0730_port_probe, + .port_remove = upd78f0730_port_remove, + .open = upd78f0730_open, + .close = upd78f0730_close, + .set_termios = upd78f0730_set_termios, + .tiocmget = upd78f0730_tiocmget, + .tiocmset = upd78f0730_tiocmset, + .dtr_rts = upd78f0730_dtr_rts, + .break_ctl = upd78f0730_break_ctl, +}; + +static struct usb_serial_driver * const serial_drivers[] = { + &upd78f0730_device, + NULL +}; + +module_usb_serial_driver(serial_drivers, id_table); + +MODULE_DESCRIPTION(DRIVER_DESC); +MODULE_AUTHOR(DRIVER_AUTHOR); +MODULE_LICENSE("GPL"); -- 2.1.4 -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
