* Grygorii Strashko <grygorii.stras...@ti.com> [170118 10:05]: > > > On 01/18/2017 10:53 AM, Tony Lindgren wrote: > > Hi, > > > > * Bin Liu <b-...@ti.com> [170118 06:26]: > >> With this v3, I still get -71 error when a device is plugged to a hub to > >> musb. It doesn't happen though if the device is already plugged to the hub > >> before attaching the hub to musb. > >> > >> [ 177.579300] usb 1-1: reset high-speed USB device number 2 using > >> musb-hdrc > >> [ 177.719308] usb 1-1: device descriptor read/64, error -71 > >> [ 178.350297] usb 1-1.1: new high-speed USB device number 4 using > >> musb-hdrc > > > > I think the -71 issue is a different regression. I've verified that v4.8.y > > does not have this, but v4.9.y does have it. > > > > So far the easiest way for me to reproduce the -71 problem is by plugging > > a USB drive into a connected hub. If I connect the hub with USB drive > > already > > plugged into the hub, it does not happen. > > > > With the hub connected musb is already active when the USB drive is plugged > > This is not exactly try, i think, because cppi can be in inactive state > because of autosuspend (all calls are paired).
Musb is active when there's something connected meaning cppi41 is clocked when a hub is connected. The actual runtime PM implementation happens for the interconnect target module for both musb and cppi41 in hwmod.c code. > > in. So I'm now suspecting this -71 regression is not related to runtime PM > > changes. Bisect and boot and plug devices time I think unless you have > > better ideas? > > > >> And I still get -115 error flooding with thumb drive. > >> > >> [ 236.880068] cppi41-dma-engine 47400000.dma-controller: cppi41_irq pm > >> runtime get: -115 > >> > >> I tested with TI AM335x GP EVM. The problems happen on both musb ports. > > > > OK. So it's pointless to try to play with the autosuspend timeout. > > > > Let's just do a WARN(!pm_runtime_active(cdd->ddev.dev->parent)) there > > until we have musb_cppi41.c dma calls properly paired and don't have > > dma requests lingering. > > > > Care to try the updated patch below? It won't help with the -71 issue > > but the $subject issue should be fixed. And you should not see the > > WARN() trigger with your tests presumably. > > > > Sry, but wouldn't be more simple and safe just to drop PM runtime from this > driver, > as it is part of musb and musb PM state expected to be handled properly by PM > runtime now. Well we still need PM runtime in cppi41 to initialize it when it gets probed and idle it when not used even if musb modules are not loaded. Unfortunately until musb_cppi41.c dma calls are fixed, we can't do any sane use counting in cppi41.c without adding timeout handling to it. > More over, There is another possibility related to the current PM runtime > implementation and autosuspend > - it might introduce delay between time when musb request desc push and time > when cppi will actually > put this desc in HW queue if cppi was not active. > For example, there might not be -71 error seen if CPPI autosuspend is disabled > (cppi is active all the time) before plug-in hub and then USB drive. I already checked that. The -71 error seems to be a separate issue. Regards, Tony -- To unsubscribe from this list: send the line "unsubscribe linux-usb" in the body of a message to majord...@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html