Hi Peter,
On Mon, Jan 29, 2018 at 11:33:15AM +0800, Peter Chen wrote:
> On Wed, Jan 24, 2018 at 06:14:39PM +0100, Sebastian Reichel wrote:
> > Traditionally, PORTSC should be set before initializing ULPI phys. But
> > setting PORTSC before powering on the phy results in a kernel freeze
> > on imx53 based GE PPD. As a workaround this initializes the phy early
> > in the imx platform code and disables phy power management from the
> > core.
> >
> > Signed-off-by: Fabien Lahoudere <fabien.lahoud...@collabora.co.uk>
> > Signed-off-by: Sebastian Reichel <sebastian.reic...@collabora.co.uk>
> > ---
> > drivers/usb/chipidea/ci_hdrc_imx.c | 12 ++++++++++++
> > 1 file changed, 12 insertions(+)
> >
> > diff --git a/drivers/usb/chipidea/ci_hdrc_imx.c
> > b/drivers/usb/chipidea/ci_hdrc_imx.c
> > index de155c80eb70..e431c5aafe35 100644
> > --- a/drivers/usb/chipidea/ci_hdrc_imx.c
> > +++ b/drivers/usb/chipidea/ci_hdrc_imx.c
> > @@ -83,6 +83,7 @@ struct ci_hdrc_imx_data {
> > struct clk *clk;
> > struct imx_usbmisc_data *usbmisc_data;
> > bool supports_runtime_pm;
> > + bool override_phy_control;
> > bool in_lpm;
> > /* SoC before i.mx6 (except imx23/imx28) needs three clks */
> > bool need_three_clks;
> > @@ -254,6 +255,7 @@ static int ci_hdrc_imx_probe(struct platform_device
> > *pdev)
> > int ret;
> > const struct of_device_id *of_id;
> > const struct ci_hdrc_imx_platform_flag *imx_platform_flag;
> > + struct device_node *np = pdev->dev.of_node;
> >
> > of_id = of_match_device(ci_hdrc_imx_dt_ids, &pdev->dev);
> > if (!of_id)
> > @@ -288,6 +290,14 @@ static int ci_hdrc_imx_probe(struct platform_device
> > *pdev)
> > }
> >
> > pdata.usb_phy = data->phy;
> > +
> > + if (of_device_is_compatible(np, "fsl,imx53-usb") && pdata.usb_phy &&
> > + of_usb_get_phy_mode(np) == USBPHY_INTERFACE_MODE_ULPI) {
> > + pdata.flags |= CI_HDRC_OVERRIDE_PHY_CONTROL;
> > + data->override_phy_control = true;
> > + usb_phy_init(pdata.usb_phy);
> > + }
> > +
> > pdata.flags |= imx_platform_flag->flags;
> > if (pdata.flags & CI_HDRC_SUPPORTS_RUNTIME_PM)
> > data->supports_runtime_pm = true;
> > @@ -341,6 +351,8 @@ static int ci_hdrc_imx_remove(struct platform_device
> > *pdev)
> > pm_runtime_put_noidle(&pdev->dev);
> > }
> > ci_hdrc_remove_device(data->ci_pdev);
> > + if (data->override_phy_control)
> > + usb_phy_shutdown(data->phy);
> > imx_disable_unprepare_clks(&pdev->dev);
> >
>
> Sebastian, I have a question, do you have any USB or generic PHY drivers
> for ULPI bus, any power controls are needed for your ULPI peripheral?
The devicetree for GE PPD is available in the mainline kernel:
$ grep -A9 "usbphy[23] {" arch/arm/boot/dts/imx53-ppd.dts
usbphy2: usbphy2 {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio4 4 GPIO_ACTIVE_LOW>;
clock-names = "main_clk";
clock-frequency = <24000000>;
clocks = <&clks IMX5_CLK_CKO2>;
assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks
IMX5_CLK_OSC>;
assigned-clock-parents = <&clks IMX5_CLK_OSC>;
};
usbphy3: usbphy3 {
compatible = "usb-nop-xceiv";
reset-gpios = <&gpio2 19 GPIO_ACTIVE_LOW>;
clock-names = "main_clk";
clock-frequency = <24000000>;
clocks = <&clks IMX5_CLK_CKO2>;
assigned-clocks = <&clks IMX5_CLK_CKO2_SEL>, <&clks
IMX5_CLK_OSC>;
assigned-clock-parents = <&clks IMX5_CLK_OSC>;
};
So currently the machine only uses drivers/usb/phy/phy-generic.c. Both
USB phys are actually SMSC USB3315, which is also detected by the kernel:
root@csmon :~# cat /sys/bus/ulpi/devices/ci_hdrc.*.ulpi/uevent
DEVTYPE=ulpi_device
MODALIAS=ulpi:v0424p0006
DEVTYPE=ulpi_device
MODALIAS=ulpi:v0424p0006
So maybe drivers/usb/phy/phy-ulpi.c should be used, but I don't see
a simple way to do so and using the generic PHY works.
-- Sebastian
signature.asc
Description: PGP signature
