On 09 December 2014 11:23 Geert Uytterhoeven wrote:

Hi Geert,

> Subject: [PATCH 1/4] watchdog: da9063: Add restart handler support
> 
> Register a restart handler for the da9063 watchdog.  System restart is
> triggered by sending the shutdown command to the PMIC.
> As more-suitable restart handlers may exist, the priority of the
> watchdog restart handler is set to 128.
> 
> The actual restart method was inspired by a platform-specific patch from
> the BSP by Hisashi Nakamura <[email protected]>.
> 
> Signed-off-by: Geert Uytterhoeven <[email protected]>
> ---
> Tested on r8a7791/koelsch
> ---

[...]

+static int da9063_wdt_restart_handler(struct notifier_block *this,
+                                     unsigned long mode, void *cmd)
+{
+       struct da9063_watchdog *wdt = container_of(this,
+                                                  struct da9063_watchdog,
+                                                  restart_handler);
+       int ret;
+
+       ret = regmap_write(wdt->da9063->regmap, DA9063_REG_CONTROL_F,
+                          DA9063_SHUTDOWN);

I am stating the obvious here.

DA9063_REG_CONTROL_F, DA9063_SHUTDOWN will cause the sequencer to
power down to RESET Mode -- which means if this I2C command succeeds 
there will be a sudden loss of power and any unsaved information will be 
lost after this point.

This is exactly how I have done it in the past.

+       if (ret)
+               dev_alert(wdt->da9063->dev, "Failed to shutdown (err = %d)\n",
+                         ret);
+
+       return NOTIFY_DONE;
+}
+

[...]

>  static const struct watchdog_info da9063_watchdog_info = {
>       .options = WDIOF_SETTIMEOUT | WDIOF_KEEPALIVEPING,
>       .identity = "DA9063 Watchdog",
> @@ -163,14 +182,25 @@ static int da9063_wdt_probe(struct
> platform_device *pdev)
>       dev_set_drvdata(&pdev->dev, wdt);
> 
>       ret = watchdog_register_device(&wdt->wdtdev);
> +     if (ret)
> +             return ret;
> 
> -     return ret;
> +     wdt->restart_handler.notifier_call = da9063_wdt_restart_handler;
> +     wdt->restart_handler.priority = 128;
> +     ret = register_restart_handler(&wdt->restart_handler);
> +     if (ret)
> +             dev_err(wdt->da9063->dev,
> +                     "Failed to register restart handler (err = %d)\n", ret);

 (I guess this is intentional).. if the restart handler doesn't get registered 
then
this problem is just ignored and not counted as a real error.

> +
> +     return 0;
>  }
> 
>  static int da9063_wdt_remove(struct platform_device *pdev)
>  {
>       struct da9063_watchdog *wdt = dev_get_drvdata(&pdev->dev);
> 
> +     unregister_restart_handler(&wdt->restart_handler);
> +
>       watchdog_unregister_device(&wdt->wdtdev);
> 
>       return 0;

Despite the above, these are just my comments.
It all looks fine to me.

Acked-by: Steve Twiss <[email protected]>

Regards,
Steve
--
To unsubscribe from this list: send the line "unsubscribe linux-watchdog" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Reply via email to