Hi Adrian,
We observed that this can happen for any rate for some SNR values.
If the SNR is strong enough for the given MCS this won't happen.
But when the SNR approaches the transition region when
error rate starts to increase, this problem will be observed.
So this can happen even for MCS0->MCS4 when the client is far from the AP
and specially when it's moving.
Thanks,
Ali
On 14-10-29 04:34 PM, Adrian Chadd wrote:
Just finally -
MCS20 -> MCS23 are very sensitive to changing channel anything. See if
you can find or make some required SNR curves for each MCS rate.
So although it doesn't surprise me to find this is happening, it's
very cute that someone's gone and done the work of figuring out how to
improve the rate control algorithm to take it into account. I'm kinda
thinking about how to do that with FreeBSD right now.
Do you get the same pattern on say, MCS0->MCS4 over a 4ms long aggregate frame?
-adrian
On 25 October 2014 13:35, Ali Abedi <a2ab...@uwaterloo.ca> wrote:
Thank you for sharing the story.
Even if I consider interference as a possibility, still I can't justify the
higher
chance of frame loss in the second half of the aggregate frame.
We use
PCI-express 3 antenna dual band cards
product: AR93xx Wireless Network Adapter
and/or
Atheors AR5B97 which is a 2.4 GHz dual antenna internal card in a laptop
we also tried TP-LINK TL-WDN4200 N900 as the receiver.
However we see the same results.
we mostly use MCS 20-23, sgi = 0, 20 MHz channels.
The loss pattern is something like this
(each line is an imaginary aggregated frame and each bit is the fate of the
MPDU)
11111111111100011000000000000
11111110001101011010000000000
11111000000000000000000000000
11111111111010100000000000000
11111100101010000000000000000
The interesting part is that with the start of the next frame error rate
goes down initially
then it goes up again in the second portion of the packet.
Best,
Ali
On 25/10/2014 2:30 PM, Adrian Chadd wrote:
On 25 October 2014 08:28, Ali Abedi <a2ab...@uwaterloo.ca> wrote:
Hi Adrian,
We have a high end spectrum analyzer. So we are sure there is no background
interference
We run our experiments in the 5 GHZ spectrum. The channel conditions can
still vary due to
the movement of the people in the vicinity of the experiment setup. We
select a rate that
experiences at least 20% error on average. Since if the error is 100% or 0%
it's not interesting
for us.
My point is if the channel conditions change the distribution of failed
packets should be uniform.
The first and second half of the packets have the same chance to be
received successfully.
Here's a little story.
My first wifi contract had me spend months trying to figure out why an
AP was losing its mind. It'd get stuck in a "stuck beacon" loop and
only a hard powercycle of /all/ of the access points in an area would
clear it.
It turned out that the PCB design had some non-grounded /
non-populated tracks that just "happened" to form a 2GHz resonator.
Once we grounded those tracks, the APs started behaving themselves.
The company in question spent months with high end spectrum analysis
kit in the lab (where it never happened) and underground (where it did
happen.) It's only after they stuck the spectrum analyser probe
_inside the access point_ right up close to the NIC did they see it.
Here's the spectrum analyser traces. You can see the peak.
http://www.creative.net.au/ath/
So, weirder crap has happened.
Which NICs and which MCS rates are you using?
-adrian
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majord...@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
