[PATCH RFC v3 3/3] ath9k: parse the device configuration from an OF node

[Martin Blumenstingl]

This makes it possible to configure ath9k based devices using
devicetree. That makes some out-of-tree "convert devicetree to
ath9k_platform_data glue"-code obsolete.

Signed-off-by: Martin Blumenstingl <martin.blumensti...@googlemail.com>
---
changes in v2 -> v3:
- replaced qca,eeprom-name with a boolean "qca,no-eeprom". The name of the
  eeprom firmware file is now generated based on the following pattern:
  ath9k-eeprom-<bus>-<id>.bin

 drivers/net/wireless/ath/ath9k/init.c | 68 +++++++++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/drivers/net/wireless/ath/ath9k/init.c 
b/drivers/net/wireless/ath/ath9k/init.c
index a0f4a52..9521bc8 100644
--- a/drivers/net/wireless/ath/ath9k/init.c
+++ b/drivers/net/wireless/ath/ath9k/init.c
@@ -20,6 +20,8 @@
 #include <linux/slab.h>
 #include <linux/ath9k_platform.h>
 #include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_net.h>
 #include <linux/relay.h>
 #include <net/ieee80211_radiotap.h>
 
@@ -555,6 +557,68 @@ static int ath9k_init_platform(struct ath_softc *sc)
        return 0;
 }
 
+static int ath9k_of_init(struct ath_softc *sc)
+{
+       struct device_node *np = sc->dev->of_node;
+       struct ath_hw *ah = sc->sc_ah;
+       struct ath_common *common = ath9k_hw_common(ah);
+       enum ath_bus_type bus_type = common->bus_ops->ath_bus_type;
+       const char *mac;
+       char eeprom_name[100];
+       int led_pin, ret;
+       u32 gpio_data;
+
+       if (!of_device_is_available(np))
+               return 0;
+
+       ath_dbg(common, CONFIG, "parsing configuration from OF node\n");
+
+       if (!of_property_read_u32(np, "qca,led-pin", &led_pin))
+               ah->led_pin = led_pin;
+
+       if (!of_property_read_u32(np, "qca,gpio-mask", &gpio_data))
+               ah->gpio_mask = gpio_data;
+
+       if (!of_property_read_u32(np, "qca,gpio-val", &gpio_data))
+               ah->gpio_val = gpio_data;
+
+       if (of_property_read_bool(np, "qca,clk-25mhz"))
+               ah->is_clk_25mhz = true;
+
+       if (of_property_read_bool(np, "qca,led-active-high"))
+               ah->config.led_active_high = true;
+
+       if (of_property_read_bool(np, "qca,disable-2ghz"))
+               ah->disable_2ghz = true;
+
+       if (of_property_read_bool(np, "qca,disable-5ghz"))
+               ah->disable_5ghz = true;
+
+       if (of_property_read_bool(np, "qca,check-eeprom-endianness"))
+               ah->ah_flags &= ~AH_NO_EEP_SWAP;
+       else
+               ah->ah_flags |= AH_NO_EEP_SWAP;
+
+       if (of_property_read_bool(np, "qca,no-eeprom")) {
+               /* ath9k-eeprom-<bus>-<id>.bin */
+               scnprintf(eeprom_name, sizeof(eeprom_name),
+                         "ath9k-eeprom-%s-%s.bin",
+                         ath_bus_type_to_string(bus_type), dev_name(ah->dev));
+
+               ret = ath9k_eeprom_request(sc, eeprom_name);
+               if (ret)
+                       return ret;
+       }
+
+       mac = of_get_mac_address(np);
+       if (mac)
+               ether_addr_copy(common->macaddr, mac);
+
+       ah->ah_flags &= ~AH_USE_EEPROM;
+
+       return 0;
+}
+
 static int ath9k_init_softc(u16 devid, struct ath_softc *sc,
                            const struct ath_bus_ops *bus_ops)
 {
@@ -611,6 +675,10 @@ static int ath9k_init_softc(u16 devid, struct ath_softc 
*sc,
        if (ret)
                return ret;
 
+       ret = ath9k_of_init(sc);
+       if (ret)
+               return ret;
+
        if (ath9k_led_active_high != -1)
                ah->config.led_active_high = ath9k_led_active_high == 1;
 
-- 
2.9.0

--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majord...@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html