On 2017-12-01 20:35, Maxime Bizon wrote:
On Fri, 2017-12-01 at 19:18 +0530, ako...@codeaurora.org wrote:
Hope CONFIG_MAC80211_DEBUGFS is enabled in your build.
it wasn't and IMHO it's confusing because tx rate is filled by the
other
drivers without it.
I now have the following warning:
[ 96.174967] ------------[ cut here ]------------
[ 96.179640] WARNING: CPU: 0 PID: 609 at net/wireless/util.c:1254
cfg80211_calculate_bitrate+0x174/0x220
[ 96.189538] invalid rate bw=1, mcs=9, nss=2
[ 96.219736] CPU: 0 PID: 609 Comm: hostapd Not tainted
4.14.3-00381-gec9756b0f64d #28
[ 96.227910] Hardware name: Marvell Kirkwood (Flattened Device Tree)
[ 96.235450] [<80010124>] (unwind_backtrace) from [<8000d9ec>]
(show_stack+0x10/0x14)
[ 96.247180] [<8000d9ec>] (show_stack) from [<8002016c>]
(__warn+0xdc/0xf8)
[ 96.254243] [<8002016c>] (__warn) from [<800201bc>]
(warn_slowpath_fmt+0x34/0x44)
[ 96.262016] [<800201bc>] (warn_slowpath_fmt) from [<8064dfdc>]
(cfg80211_calculate_bitrate+0x174/0x220)
[ 96.272652] [<8064dfdc>] (cfg80211_calculate_bitrate) from
[<806692d4>] (nl80211_put_sta_rate+0x44/0x1dc)
[ 96.282509] [<806692d4>] (nl80211_put_sta_rate) from [<8066001c>]
(nl80211_send_station+0x388/0xaf0)
[ 96.292261] [<8066001c>] (nl80211_send_station) from [<8066082c>]
(nl80211_get_station+0xa8/0xec)
[ 96.304166] [<8066082c>] (nl80211_get_station) from [<80509c20>]
(genl_rcv_msg+0x2dc/0x34c)
[ 96.313324] [<80509c20>] (genl_rcv_msg) from [<8050890c>]
(netlink_rcv_skb+0x84/0xdc)
[ 96.321880] [<8050890c>] (netlink_rcv_skb) from [<805093c0>]
(genl_rcv+0x20/0x34)
[ 96.329668] [<805093c0>] (genl_rcv) from [<80508188>]
(netlink_unicast+0x12c/0x1e0)
[ 96.338408] [<80508188>] (netlink_unicast) from [<805085d8>]
(netlink_sendmsg+0x2e0/0x304)
[ 96.350736] [<805085d8>] (netlink_sendmsg) from [<804b5f9c>]
(sock_sendmsg+0x14/0x24)
[ 96.358656] [<804b5f9c>] (sock_sendmsg) from [<804b66e8>]
(___sys_sendmsg+0x1c8/0x20c)
[ 96.367093] [<804b66e8>] (___sys_sendmsg) from [<804b739c>]
(__sys_sendmsg+0x40/0x64)
[ 96.375276] [<804b739c>] (__sys_sendmsg) from [<8000a3e0>]
(ret_fast_syscall+0x0/0x44)
[ 96.383455] ---[ end trace da8257d6a850e91a ]---
# iw dev wlan1 station dump
Station e4:42:a6:24:c8:95 (on wlan1)
inactive time: 550 ms
rx bytes: 41217
rx packets: 152
tx bytes: 49397
tx packets: 107
tx retries: 0
tx failed: 1
rx drop misc: 0
signal: -62 [-66, -65, -83] dBm
signal avg: -61 [-65, -65, -78] dBm
tx bitrate: VHT-MCS 9 short GI VHT-NSS 2
rx bitrate: 360.0 MBit/s VHT-MCS 8 40MHz short GI VHT-NSS 2
rx duration: 0 us
authorized: yes
authenticated: yes
associated: yes
preamble: long
WMM/WME: yes
MFP: no
TDLS peer: no
DTIM period: 2
beacon interval:96
short slot time:yes
connected time: 5 seconds
Thanks
Hope 10.2.4-1.0-00029 Firmware binary works for you.
I will check this warning.
Thanks,
Anil.
