Hi Bruce,
Could you please help to merge below patches to the preempt-rt kernel
branch "v6.1/standard/preempt-rt/ti-sdk-6.1/ti-j7xxx"?
This is preempt-rt kernel to upgrade BSP to TI SDK
ti-processor-sdk-linux-edgeai-am62axx-evm-09_01_00_07.
The following changes since commit a54e02fccaea82a741c0e34a72b7bffb47bfcda3:
Merge branch 'v6.1/standard/base' into
v6.1/standard/preempt-rt/ti-sdk-6.1/ti-j7xxx (2024-01-03 15:54:23 -0500)
are available in the Git repository at:
https://github.com/xulinsun/ti-j72x
v6.1/standard/preempt-rt/ti-sdk-6.1/ti-j7xxx
for you to fetch changes up to 53acd8e4944a31f6e5240d332ba28508adf6b40b:
arm64: dts: ti: k3-am62p5-sk: enable uart as wakeup source
(2024-01-04 10:43:54 +0800)
----------------------------------------------------------------
Andrew Davis (2):
phy: ti: gmii-sel: Allow parent to not be syscon node
phy: ti: gmii-sel: Fix register offset when parent is not a
syscon node
Aradhya Bhatia (11):
drm/tidss: Add support for AM62P DSS0
arm64: dts: ti: k3-am62p5-sk: Enable main_i2c0
arm64: dts: ti: k3-am62p-main: Add support for DSS0
arm64: dts: ti: k3-am62p5-sk: Enable HDMI display on DSS0
arm64: dts: ti: Add Microtips OLDI Panel-1 Overlay for AM62P5-SK
arm64: dts: ti: Add Microtips OLDI Panel-2 Overlay for AM62P5 SK
dt-bindings: display: ti,am65x-dss: Add support for AM62P DSS0
drm/tidss: Add support for AM62P DSS1
arm64: dts: ti: k3-am62p: Add memory regions for DSS1, DSI and
DPHY-TX
arm64: dts: ti: k3-am62p-main: Add DSS1, DSI and DPHY-TX
arm64: dts: ti: k3-am62p5-sk: Add RPi DSI Panel
Brandon Brnich (7):
arm64: dts: ti: k3-am62p: Enable video encode/decode
arm64: dts: ti: k3-am62p: Reserve 128 MiB for CMA on 62p
media: chips-media: wave5: Update queue initialization logic
arm64: dts: ti: k3-am62p-main: SRAM allocation for VPU
media: chips-media: wave5: Update Pixel Rate Logic
arm64: dts: ti: k3-am62p-main: VPU Frequency Operating Points
media: img: vxe-vxd: decoder: Remove Padding in Output
Bryan Brattlof (6):
HACK: cpufreq: ti-cpufreq: extend am625 efuse table
arm64: dts: ti: k3-am62p: introduce OPP table
arm64: dts: ti: k3-am62p: disable 1v8 modes
arm64: dts: ti: k3-am62p: add required mmc properties
arch: dts: ti: k3-am62p5-sk: add sdhci0 as a boot option
HACK: arm64: dts: ti: k3-am62p: add dll delay mapping for emmc
Dave Stevenson (8):
Input: edt-ft5x06: Poll the device if no interrupt is configured.
Input: edt-ft54x6: Clean up timer and workqueue on remove
input: edt-ft5x06: Handle unreliable TOUCH_UP events
input: edt-ft5x06: Only look at the number of points reported
input: edt-ft5x06: Only read data for number of points reported
input: edt-ft5x06: Include I2C details in names for the devices
drm/panel: Add prepare_upstream_first flag to drm_panel
drm/tc358762: Set the pre_enable_upstream_first flag to configure
DSI host
David Lechner (8):
counter/ti-eqep: implement over/underflow events
counter/ti-eqep: add support for direction
counter/ti-eqep: add support for unit timer
docs: counter: add unit timer sysfs attributes
counter/ti-eqep: add support for latched position
docs: counter: add latch_mode and latched_count sysfs attributes
counter/ti-eqep: add support for edge capture unit
docs: counter: add edge_capture_unit_* attributes
Devarsh Thakkar (9):
arm64: dts: ti: k3-am62p5-sk: Reserve memory for remote cores
arm64: dts: ti: k3-am62p5-sk: Bump up cma to 576M
arm64: dts: ti: k3-am62x-sk-common: Add simple-framebuffer node
dt-bindings: display: ti,am65x-dss: Add support for common1 region
arm64: dts: ti: Add common1 register space for all supported SoCs
dt-bindings: display: ti,am65x-dss: Add support for display
sharing mode
arm64: dts: ti: k3-am62p: Add overlay to use DSS in display
sharing mode
drm/tidss: Add support for display sharing
arm64: dts: ti: Fix IRQ number for ILI251x touchscreen
Dhruva Gole (3):
firmware: ti_sci: Change the lpm context address to be 32-bit
addressable
arm64: dts: ti: k3-am62: Add main gpio keys based wake irq example
arm64: dts: ti: k3-am62x-sk-mcu-gpio-wakeup: Enable mcu_gpio nodes
Guillaume La Roque (1):
net: ethernet: ti: cpsw-proxy-client: Fix size of ipv4_addr member
Hari Nagalla (6):
arm64: dts: ti: k3-am62p5-sk: Attach mboxes and reserve memory to
remote cores
remoteproc: k3-r5: Introduce PM suspend/resume handlers
remoteproc: k3-r5: Introduce MCU wakeup handlers
arm64: dts: ti: k3-am62a-mcu: Enable MCU wakeup for R5F
arm64: dts: ti: k3-am62a7-sk: HACK: Reduce mailbox fifos
arm64: dts: ti: k3-am62p: Add SRAM node for MCU-R5 and set wakeup
source
Jackson Lee (2):
media: chips-media: wave5: Enable Prepending Headers to IDR Frames
media: chips-media: wave5: Allow using bitstream buffer size
received from host
Jai Luthra (9):
arm64: dts: ti: k3-am62p5-sk: Fix pinmux for McASP1 TX
arm64: dts: ti: k3-am62p: Fix memory ranges for DMSS
arm64: dts: ti: k3-am62p: Add DMASS1 for CSI
arm64: dts: ti: k3-am62p: Add nodes for CSI-RX
arm64: dts: ti: k3-am62p5-sk: Enable peripherals for CSI cameras
arm64: dts: ti: SK-AM62*: Rename camera/audio overlays
media: ti: j721e-csi2rx: Re-use a 32KiB drain-buffer
dmaengine: ti: k3-psil-am62a: Fix SPI PDMA data
dmaengine: ti: k3-psil-am62p: Fix SPI PDMA data
Judith Mendez (18):
arm64: dts: ti: Add MCAN overlay for AM62P-SK
arm64: dts: ti: Add overlay for enabling RPi header for AM625-SK
arm64: dts: ti: Add overlay for enabling RPi header for AM62A-SK
arm64: dts: ti: Add overlay for enabling RPi header for AM62P-SK
arm64: dts: ti: Enable RPI header in K3 devices
arm64: dts: ti: Rename existing PWM overlay for AM62X-SK
arm64: dts: ti: k3-am62: Rename MCAN overlay
dt-bindings: counter: Update binding for K3 devices
arm64: dts: ti: k3-am64x: Enable eQEP
arm64: dts: ti: k3-am62x: Enable eQEP
arm64: dts: ti: k3-am62a: Enable eQEP
arm64: dts: ti: k3-am62p: Enable eQEP
counter: ti-eqep: Enable eQEP for K3 devices
arm64: dts: ti: Remove original EQEP overlay
arm64: dts: k3-am62p: Remove HS200 mode from emmc node
arm64: dts: k3-am62p: Enable HS400 speed mode
arm64: dts: k3-am62p: Enable DDR52 speed mode
arm64: dts: ti: k3-am62p: add dll delay mapping for MMC1/MMC2
MD Danish Anwar (3):
net: ti: icssg-prueth: Rename emacs_initialized variable
net: ti: icssg-prueth: Fix firmware load sequence.
net: ti: icssg-prueth: Fix TX buffer pool size in switch mode
Markus Schneider-Pargmann (22):
dt-bindings: ti, sci: Add property for partial-io-wakeup-sources
dt-bindings: can: m_can: Add wakeup-source property
arm64: dts: ti: am62: Add serial aliases
arm64: dts: ti: k3-am62: Mark mcu_mcan0/1 as wakeup-source
arm64: dts: ti: k3-am62: Add partial-io wakeup sources
arm64: dts: ti: k3-pinctrl: Add WKUP_EN flag
arm64: dts: ti: Wakeup support for k3-am62x mcan overlay
arm64: dts: ti: Add am62-lp-sk mcu_uart0 overlay
arm64: dts: ti: Add am62-lp-sk mcu_mcan0/1 overlay
firmware: ti_sci: Partial-IO support
can: m_can: Map WoL to device_set_wakeup_enable
can: m_can: Support pinctrl wakeup state
serial: 8250: omap: Remove unused wakeups_enabled
serial: 8250: omap: Set wakeup capable, do not enable
serial: 8250: omap: Support wakeup pinctrl state
arm64: dts: ti: k3-am62a7-sk: Add serial aliases
arm64: dts: ti: k3-am62a-mcu: Mark mcu_mcan0/1 as wakeup-source
arm64: dts: ti: k3-am62a: Add partial-io wakeup sources
arm64: dts: ti: k3-am62-lp-sk: Remove tps65219 power-button
can: m_can: Remove debug output in set_wol
firmware: ti_sci: Do not expect a response for entering partial-io
firmware: ti_sci: Use while loop after entering partial-io
Matt Ranostay (1):
PCI: j721e: pci-j721e-ep: Fix missing max_lanes member
Murali Karicheri (1):
net: hsr: Add support for MC filtering at the slave device
Nick Hollinghurst (1):
input: touchscreen: edt-ft5x06: Suppress bogus data on startup
Praneeth Bajjuri (1):
Revert "spi: omap2-mcspi: Add FIFO support without DMA"
Prasanth Babu Mantena (5):
arm64: media: wave5: Add runtime PM support for Codec
arm64: media: wave5: Add Support for frequency points
arm64: dts: ti: k3-am62a-main: Add OPP table to the VPU codec node
arm64: dts: ti: k3-j784s4-main: Add OPP table to two instances of VPU
arm64: dts: ti: k3-j721s2-main: Add OPP table to the VPU node
Rahul T R (3):
drm/panel-simple: Add VESA timings for Raspberry Pi 7" DSI panel
arm64: dts: ti: k3-j721e-main: Add DSI and DPHY-TX
arm64: dts: ti: k3-j721e-beagleboneai64: Add DSI RPi Panel
Randolph Sapp (5):
dt-bindings: gpu: ti: rogue: add am62p node updates
arm64: dts: k3-am62p: add bxs-4-64 gpu
arm64: dts: k3-am62p: gpu: add the assigned-clock-rates
dt-bindings: crypto: ti: mcrc: add includes to example
dt-bindings: pci: ti: am65-pci-host: fix syntax in example
Ravi Gunasekaran (3):
arm64: dts: ti: k3-am62p5-sk: Add CPSW MDIO pinctrl info
net: ti: icssg-prueth: Add multicast filtering support in HSR mode
net: ti: icssg-prueth: Update VLAN FDB table
Roger Quadros (12):
usb: dwc3-am62: call of_platform_depopulate in .remove()
usb: dwc3-am62: fix error on module removal
usb: dwc3: complain if DWC3_GUSB3PIPECTL_SUSPHY is set at start
and clear it
usb: dwc3-am62: Strictly follow recommended Init sequence
dt-bindings: usb/ti,am62-usb.yaml: Add vddcore supply
usb: dwc3-am62: add PHY core voltage selection support
arm64: dts: ti: k3-am625-sk: add VDD_CORE regulator
arm64: dts: ti: k3-am62: Add vddcore-supply to USB modules
arm64: dts: ti: k3-am62/a: use sub-node for USB_PHY_CTRL registers
usb: dwc3-am62: Fix PHY core voltage selection
Revert "dt-bindings: usb/ti,am62-usb.yaml: Add vddcore supply"
Revert "arm64: dts: ti: k3-am62: Add vddcore-supply to USB modules"
Ronald Wahl (1):
dmaengine: ti: k3-psil-am62: Fix SPI PDMA data
Siddharth Vadapalli (7):
dmaengine: ti: k3-udma-glue: Add function to parse channel by ID
dmaengine: ti: k3-udma-glue: Update name for remote RX channel device
dmaengine: ti: k3-udma-glue: Add function to request TX channel by ID
dmaengine: ti: k3-udma-glue: Add function to request RX channel by ID
net: ethernet: ti: Add RPMsg structures for Ethernet Switch Firmware
net: ethernet: ti: Add CPSW Proxy Client driver
arm64: dts: ti: am654-base-board: Enable PHY interrupts for ICSSG2
Tomi Valkeinen (16):
arm64: dts: ti: k3-am65-main: fix DSS irq trigger type
Revert "drm/tidss: Annotate dma-fence critical section in commit
path"
drm/tidss: Use pm_runtime_resume_and_get()
drm/tidss: Use PM autosuspend
drm/tidss: Remove early fb
drm/tidss: Drop useless variable init
drm/tidss: Fix OLDI default rate setup
drm/tidss: Return error value from from softreset
drm/tidss: Check for K2G in in dispc_softreset()
drm/tidss: Add simple K2G manual reset
drm/tidss: Fix dss reset
drm/tidss: Add dispc_is_idle()
drm/tidss: IRQ code cleanup
drm/tidss: Add some support for splash-screen
drm/tidss: Fix atomic_flush check
drm/tidss: Use DRM_PLANE_COMMIT_ACTIVE_ONLY
Tony Lindgren (4):
bus: ti-sysc: Build driver for TI K3 SoCs
bus: ti-sysc: Configure uart quirks for k3 SoC
dt-bindings: input: gpio-keys: Allow optional dedicated wakeirq
Input: gpio-keys - Add system suspend support for dedicated wakeirqs
Vaishnav Achath (1):
spi: omap2-mcspi: Add FIFO support without DMA
Vibhore Vardhan (10):
arm64: dts: ti: k3-am62a-wakeup: Enable RTC node
HACK: arm64: dts: ti: Configure am62a pinctrl-single for wake-up
interrupts
arm64: dts: ti: k3-am62a7-sk: enable uart as wakeup source
Revert "arm64: dts: ti: k3-am62: Add main
Revert "arm64: dts: ti: Add am62-lp-sk mcu_mcan0/1 overlay"
Revert "arm64: dts: ti: Add am62-lp-sk mcu_uart0 overlay"
Revert "arm64: dts: ti: Wakeup support for k3-am62x mcan overlay"
arm64: dts: ti: k3-am62: Create a single LPM wkup sources overlay
HACK: arm64: dts: ti: Configure am62p pinctrl-single for wake-up
interrupts
arm64: dts: ti: k3-am62p5-sk: enable uart as wakeup source
Vignesh Raghavendra (12):
arm64: dts: ti: k3-am62p: Add nodes for more IPs
arm64: dts: ti: k3-am62p5-sk: Updates for SK EVM
arm64: dts: ti: k3-am62p: add the USB sub-system
dmaengine: ti: k3-udma: Fix BCHAN count with UHC and HC channels
dmaengine: ti: k3-udma: Add PSIL threads for AM62P
dt-bindings: dma: ti: k3-bcdma: Add bindings for BCDMA CSI RX
HACK: arm64: dts: ti: k3-am62p-wakeup: Mark wkup_conf as
syscon/simple-mfd compatible
watchdog: rti_wdt: Use managed APIs to handle runtime PM
watchdog: rti_wdt: Drop RPM watchdog when unused
arm64: dts: ti: k3-am642-evm/sk: Mark mcu_gpio_intr as reserved
arm64: dts: ti: k3-am62p5-sk: Mark mcu gpio and mcu_gpio_intr as
reserved
arm64: dts: ti: k3-am62x-sk-common: Mark mcu gpio and
mcu_gpio_intr as reserved
Vishal Mahaveer (2):
arm64: dts: ti: k3-am62: Rename MCU GPIO wakeup support overlay
arm64: dts: ti: k3-am62p-main: Update GPU frequency
Documentation/ABI/testing/sysfs-bus-counter | 108 +++++-
Documentation/devicetree/bindings/arm/keystone/ti,sci.yaml | 6 +
Documentation/devicetree/bindings/counter/ti-eqep.yaml | 9 +-
Documentation/devicetree/bindings/crypto/ti,mcrc.yaml | 3 +
Documentation/devicetree/bindings/display/ti/ti,am65x-dss.yaml | 101
++++-
Documentation/devicetree/bindings/dma/ti/k3-bcdma.yaml | 77 +++-
Documentation/devicetree/bindings/gpu/ti,rogue.yaml | 81 +++-
Documentation/devicetree/bindings/input/gpio-keys.yaml | 41 +-
Documentation/devicetree/bindings/net/can/bosch,m_can.yaml | 4 +
Documentation/devicetree/bindings/pci/ti,am65-pci-host.yaml | 1 +
arch/arm64/boot/dts/ti/Makefile | 30 +-
arch/arm64/boot/dts/ti/k3-am62-lp-sk.dts | 1 -
arch/arm64/boot/dts/ti/k3-am62-main.dtsi | 39 +-
arch/arm64/boot/dts/ti/k3-am62-mcu.dtsi | 2 +
arch/arm64/boot/dts/ti/k3-am62-wakeup.dtsi | 10 +
arch/arm64/boot/dts/ti/k3-am62.dtsi | 4 +
arch/arm64/boot/dts/ti/k3-am625-sk-mcu-gpio-wakeup.dtso | 40 --
arch/arm64/boot/dts/ti/{k3-am625-sk-rpi-hdr-pwm.dtso =>
k3-am625-sk-pwm.dtso} | 0
arch/arm64/boot/dts/ti/k3-am625-sk-rpi-hdr-ehrpwm.dtso | 104 ++++++
arch/arm64/boot/dts/ti/k3-am625-sk.dts | 11 +
arch/arm64/boot/dts/ti/k3-am62a-main.dtsi | 65 +++-
arch/arm64/boot/dts/ti/k3-am62a-mcu.dtsi | 3 +
arch/arm64/boot/dts/ti/k3-am62a-wakeup.dtsi | 11 +-
arch/arm64/boot/dts/ti/k3-am62a.dtsi | 4 +
arch/arm64/boot/dts/ti/k3-am62a7-sk-rpi-hdr-ehrpwm.dtso | 104 ++++++
arch/arm64/boot/dts/ti/k3-am62a7-sk.dts | 8 +
arch/arm64/boot/dts/ti/k3-am62p-main.dtsi | 1123
++++++++++++++++++++++++++++++++++++++++++++++++++++++-
arch/arm64/boot/dts/ti/k3-am62p-mcu.dtsi | 204 ++++++++++
arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi | 47 +++
arch/arm64/boot/dts/ti/k3-am62p-wakeup.dtsi | 71 +++-
arch/arm64/boot/dts/ti/k3-am62p.dtsi | 15 +-
arch/arm64/boot/dts/ti/k3-am62p5-sk-dsi-rpi-7inch-panel.dtso | 122 ++++++
arch/arm64/boot/dts/ti/k3-am62p5-sk-dss-shared-mode.dtso | 24 ++
arch/arm64/boot/dts/ti/k3-am62p5-sk-eqep.dtso | 41 ++
arch/arm64/boot/dts/ti/k3-am62p5-sk-mcan.dtso | 122 ++++++
arch/arm64/boot/dts/ti/k3-am62p5-sk-microtips-mf101hie-panel.dtso |
79 ++++
arch/arm64/boot/dts/ti/k3-am62p5-sk-microtips-mf103hie-lcd2.dtso |
66 ++++
arch/arm64/boot/dts/ti/k3-am62p5-sk-rpi-hdr-ehrpwm.dtso | 106 ++++++
arch/arm64/boot/dts/ti/k3-am62p5-sk.dts | 762
++++++++++++++++++++++++++++++++++++-
arch/arm64/boot/dts/ti/k3-am62p5.dtsi | 47 +++
arch/arm64/boot/dts/ti/k3-am62x-sk-common.dtsi | 29 ++
arch/arm64/boot/dts/ti/{k3-am62a7-sk-csi2-imx219.dtso =>
k3-am62x-sk-csi2-imx219.dtso} | 0
arch/arm64/boot/dts/ti/{k3-am625-sk-csi2-ov5640.dtso =>
k3-am62x-sk-csi2-ov5640.dtso} | 0
arch/arm64/boot/dts/ti/{k3-am625-sk-csi2-tevi-ov5640.dtso =>
k3-am62x-sk-csi2-tevi-ov5640.dtso} | 0
arch/arm64/boot/dts/ti/k3-am62x-sk-eqep.dtso | 41 ++
arch/arm64/boot/dts/ti/{k3-am625-sk-hdmi-audio.dtso =>
k3-am62x-sk-hdmi-audio.dtso} | 0
arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso | 150 ++++++++
arch/arm64/boot/dts/ti/{k3-am625-sk-mcan.dtso =>
k3-am62x-sk-mcan.dtso} | 14 +-
arch/arm64/boot/dts/ti/k3-am64-main.dtsi | 30 ++
arch/arm64/boot/dts/ti/k3-am642-evm.dts | 6 +-
arch/arm64/boot/dts/ti/k3-am642-sk.dts | 23 +-
arch/arm64/boot/dts/ti/k3-am65-main.dtsi | 7 +-
arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 15 +-
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64-dsi-rpi-7inch-panel.dtso | 144
+++++++
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64.dts | 7 +-
arch/arm64/boot/dts/ti/k3-j721e-main.dtsi | 31 ++
arch/arm64/boot/dts/ti/k3-j721s2-main.dtsi | 23 ++
arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 46 +++
arch/arm64/boot/dts/ti/k3-pinctrl.h | 3 +
drivers/bus/Kconfig | 3 +-
drivers/bus/ti-sysc.c | 2 +
drivers/counter/Kconfig | 2 +-
drivers/counter/ti-eqep.c | 482 +++++++++++++++++++++++-
drivers/cpufreq/ti-cpufreq.c | 4 +
drivers/dma/ti/Makefile | 3 +-
drivers/dma/ti/k3-psil-am62.c | 12 +-
drivers/dma/ti/k3-psil-am62a.c | 12 +-
drivers/dma/ti/k3-psil-am62p.c | 196 ++++++++++
drivers/dma/ti/k3-psil-priv.h | 1 +
drivers/dma/ti/k3-psil.c | 1 +
drivers/dma/ti/k3-udma-glue.c | 294 +++++++++++----
drivers/dma/ti/k3-udma.c | 2 +
drivers/firmware/ti_sci.c | 144 ++++++-
drivers/firmware/ti_sci.h | 1 +
drivers/gpu/drm/bridge/panel.c | 3 +
drivers/gpu/drm/bridge/tc358762.c | 1 +
drivers/gpu/drm/panel/panel-simple.c | 39 ++
drivers/gpu/drm/tidss/tidss_crtc.c | 127 ++++++-
drivers/gpu/drm/tidss/tidss_dispc.c | 642 +++++++++++++++++++++++++++++--
drivers/gpu/drm/tidss/tidss_dispc.h | 8 +-
drivers/gpu/drm/tidss/tidss_drv.c | 80 +++-
drivers/gpu/drm/tidss/tidss_drv.h | 7 +
drivers/gpu/drm/tidss/tidss_irq.c | 54 +--
drivers/gpu/drm/tidss/tidss_kms.c | 6 +-
drivers/input/keyboard/gpio_keys.c | 69 +++-
drivers/input/touchscreen/edt-ft5x06.c | 128 ++++++-
drivers/media/platform/chips-media/wave5/wave5-helper.c | 69 ++++
drivers/media/platform/chips-media/wave5/wave5-helper.h | 5 +
drivers/media/platform/chips-media/wave5/wave5-hw.c | 2 +-
drivers/media/platform/chips-media/wave5/wave5-vpu-dec.c | 23 +-
drivers/media/platform/chips-media/wave5/wave5-vpu-enc.c | 25 +-
drivers/media/platform/chips-media/wave5/wave5-vpu.c | 72 ++++
drivers/media/platform/chips-media/wave5/wave5-vpuapi.c | 1 +
drivers/media/platform/chips-media/wave5/wave5-vpuapi.h | 3 +
drivers/media/platform/chips-media/wave5/wave5.h | 3 +
drivers/media/platform/img/vxe-vxd/decoder/vxd_v4l2.c | 57 ++-
drivers/media/platform/ti/j721e-csi2rx/j721e-csi2rx.c | 54 ++-
drivers/net/can/m_can/m_can.c | 43 +++
drivers/net/can/m_can/m_can.h | 4 +
drivers/net/ethernet/ti/Kconfig | 12 +
drivers/net/ethernet/ti/Makefile | 3 +
drivers/net/ethernet/ti/cpsw-proxy-client.c | 2176
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
drivers/net/ethernet/ti/eth_remote_msg.h | 448 ++++++++++++++++++++++
drivers/net/ethernet/ti/icssg_classifier.c | 2 +-
drivers/net/ethernet/ti/icssg_config.c | 45 ++-
drivers/net/ethernet/ti/icssg_config.h | 6 +-
drivers/net/ethernet/ti/icssg_prueth.c | 124 ++++--
drivers/net/ethernet/ti/icssg_prueth.h | 5 +-
drivers/pci/controller/cadence/pci-j721e-ep.c | 3 +
drivers/phy/ti/phy-gmii-sel.c | 14 +-
drivers/remoteproc/ti_k3_r5_remoteproc.c | 86 ++++-
drivers/tty/serial/8250/8250_omap.c | 42 ++-
drivers/usb/dwc3/core.c | 7 +
drivers/usb/dwc3/dwc3-am62.c | 87 +++--
drivers/watchdog/rti_wdt.c | 31 +-
include/drm/drm_panel.h | 10 +
include/linux/dma/k3-udma-glue.h | 8 +
include/linux/gpio_keys.h | 2 +
include/uapi/linux/counter.h | 4 +
net/hsr/hsr_device.c | 67 +++-
120 files changed, 9583 insertions(+), 548 deletions(-)
delete mode 100644 arch/arm64/boot/dts/ti/k3-am625-sk-mcu-gpio-wakeup.dtso
rename arch/arm64/boot/dts/ti/{k3-am625-sk-rpi-hdr-pwm.dtso =>
k3-am625-sk-pwm.dtso} (100%)
create mode 100644 arch/arm64/boot/dts/ti/k3-am625-sk-rpi-hdr-ehrpwm.dtso
create mode 100644 arch/arm64/boot/dts/ti/k3-am62a7-sk-rpi-hdr-ehrpwm.dtso
create mode 100644 arch/arm64/boot/dts/ti/k3-am62p-thermal.dtsi
create mode 100644
arch/arm64/boot/dts/ti/k3-am62p5-sk-dsi-rpi-7inch-panel.dtso
create mode 100644
arch/arm64/boot/dts/ti/k3-am62p5-sk-dss-shared-mode.dtso
create mode 100644 arch/arm64/boot/dts/ti/k3-am62p5-sk-eqep.dtso
create mode 100644 arch/arm64/boot/dts/ti/k3-am62p5-sk-mcan.dtso
create mode 100644
arch/arm64/boot/dts/ti/k3-am62p5-sk-microtips-mf101hie-panel.dtso
create mode 100644
arch/arm64/boot/dts/ti/k3-am62p5-sk-microtips-mf103hie-lcd2.dtso
create mode 100644 arch/arm64/boot/dts/ti/k3-am62p5-sk-rpi-hdr-ehrpwm.dtso
rename arch/arm64/boot/dts/ti/{k3-am62a7-sk-csi2-imx219.dtso =>
k3-am62x-sk-csi2-imx219.dtso} (100%)
rename arch/arm64/boot/dts/ti/{k3-am625-sk-csi2-ov5640.dtso =>
k3-am62x-sk-csi2-ov5640.dtso} (100%)
rename arch/arm64/boot/dts/ti/{k3-am625-sk-csi2-tevi-ov5640.dtso =>
k3-am62x-sk-csi2-tevi-ov5640.dtso} (100%)
create mode 100644 arch/arm64/boot/dts/ti/k3-am62x-sk-eqep.dtso
rename arch/arm64/boot/dts/ti/{k3-am625-sk-hdmi-audio.dtso =>
k3-am62x-sk-hdmi-audio.dtso} (100%)
create mode 100644
arch/arm64/boot/dts/ti/k3-am62x-sk-lpm-wkup-sources.dtso
rename arch/arm64/boot/dts/ti/{k3-am625-sk-mcan.dtso =>
k3-am62x-sk-mcan.dtso} (72%)
create mode 100644
arch/arm64/boot/dts/ti/k3-j721e-beagleboneai64-dsi-rpi-7inch-panel.dtso
create mode 100644 drivers/dma/ti/k3-psil-am62p.c
create mode 100644 drivers/net/ethernet/ti/cpsw-proxy-client.c
create mode 100644 drivers/net/ethernet/ti/eth_remote_msg.h
-=-=-=-=-=-=-=-=-=-=-=-
Links: You receive all messages sent to this group.
View/Reply Online (#13452):
https://lists.yoctoproject.org/g/linux-yocto/message/13452
Mute This Topic: https://lists.yoctoproject.org/mt/103518879/21656
Group Owner: linux-yocto+ow...@lists.yoctoproject.org
Unsubscribe: https://lists.yoctoproject.org/g/linux-yocto/unsub
[arch...@mail-archive.com]
-=-=-=-=-=-=-=-=-=-=-=-
