merged to master and yocto-5.2 branches. Bruce
On Mon, Jul 22, 2019 at 7:35 AM <quanyang.w...@windriver.com> wrote: > > From: Quanyang Wang <quanyang.w...@windriver.com> > > Hi Bruce, > > Would you please help to merge this patch to yocto-kernel-cache master? > > --------------LOG------------ > Booting Linux on physical CPU 0x0000000000 [0x410fd034] > Linux version 5.2.0-yoctodev-standard (wrsadmin@pek-qwang2-d1) (gcc version > 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb9 > Machine model: ZynqMP ZCU102 Rev1.0 > earlycon: cdns0 at MMIO 0x00000000ff000000 (options '') > printk: bootconsole [cdns0] enabled > efi: Getting EFI parameters from FDT: > efi: UEFI not found. > crashkernel reserved: 0x000000005fe00000 - 0x000000007fe00000 (512 MB) > cma: Reserved 256 MiB at 0x000000004fc00000 > psci: probing for conduit method from DT. > psci: PSCIv1.1 detected in firmware. > psci: Using standard PSCI v0.2 function IDs > psci: MIGRATE_INFO_TYPE not supported. > psci: SMC Calling Convention v1.1 > percpu: Embedded 30 pages/cpu s85208 r8192 d29480 u122880 > Detected VIPT I-cache on CPU0 > CPU features: detected: ARM erratum 845719 > Speculative Store Bypass Disable mitigation not required > Built 1 zonelists, mobility grouping on. Total pages: 1031940 > Kernel command line: console=ttyPS0,115200n8 earlycon=cdns,0xFF000000 > clk_ignore_unused root=/dev/nfs rw rootwait > nfsroot=128.224.162.137:/home/wrsadmM > Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) > Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) > software IO TLB: mapped [mem 0x4bc00000-0x4fc00000] (64MB) > Memory: 3240236K/4193280K available (12348K kernel code, 1292K rwdata, 3260K > rodata, 2112K init, 774K bss, 690900K reserved, 262144K cma-reserved) > SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 > ftrace: allocating 40981 entries in 161 pages > rcu: Preemptible hierarchical RCU implementation. > rcu: RCU restricting CPUs from NR_CPUS=256 to nr_cpu_ids=4. > Tasks RCU enabled. > rcu: RCU calculated value of scheduler-enlistment delay is 25 jiffies. > rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4 > NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 > GIC: Adjusting CPU interface base to 0x00000000f902f000 > GIC: Using split EOI/Deactivate mode > random: get_random_bytes called from start_kernel+0x32c/0x4dc with crng_init=0 > arch_timer: cp15 timer(s) running at 99.99MHz (phys). > clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: > 0x170f8de2d3, max_idle_ns: 440795206112 ns > sched_clock: 56 bits at 99MHz, resolution 10ns, wraps every 4398046511101ns > Console: colour dummy device 80x25 > Calibrating delay loop (skipped), value calculated using timer frequency.. > 199.98 BogoMIPS (lpj=399960) > pid_max: default: 32768 minimum: 301 > LSM: Security Framework initializing > Mount-cache hash table entries: 8192 (order: 4, 65536 bytes) > Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes) > ASID allocator initialised with 32768 entries > rcu: Hierarchical SRCU implementation. > EFI services will not be available. > smp: Bringing up secondary CPUs ... > Detected VIPT I-cache on CPU1 > CPU1: Booted secondary processor 0x0000000001 [0x410fd034] > Detected VIPT I-cache on CPU2 > CPU2: Booted secondary processor 0x0000000002 [0x410fd034] > Detected VIPT I-cache on CPU3 > CPU3: Booted secondary processor 0x0000000003 [0x410fd034] > smp: Brought up 1 node, 4 CPUs > SMP: Total of 4 processors activated. > CPU features: detected: 32-bit EL0 Support > CPU features: detected: CRC32 instructions > CPU: All CPU(s) started at EL2 > alternatives: patching kernel code > devtmpfs: initialized > clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: > 7645041785100000 ns > futex hash table entries: 1024 (order: 4, 65536 bytes) > xor: measuring software checksum speed > 8regs : 2292.000 MB/sec > 32regs : 2811.000 MB/sec > arm64_neon: 2130.000 MB/sec > xor: using function: 32regs (2811.000 MB/sec) > pinctrl core: initialized pinctrl subsystem > DMI not present or invalid. > NET: Registered protocol family 16 > cpuidle: using governor ladder > hw-breakpoint: found 6 breakpoint and 4 watchpoint registers. > DMA: preallocated 256 KiB pool for atomic allocations > HugeTLB registered 1.00 GiB page size, pre-allocated 0 pages > HugeTLB registered 32.0 MiB page size, pre-allocated 0 pages > HugeTLB registered 2.00 MiB page size, pre-allocated 0 pages > HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages > raid6: neonx8 gen() 1649 MB/s > raid6: neonx8 xor() 1511 MB/s > raid6: neonx4 gen() 1500 MB/s > raid6: neonx4 xor() 1434 MB/s > raid6: neonx2 gen() 1159 MB/s > raid6: neonx2 xor() 1204 MB/s > raid6: neonx1 gen() 728 MB/s > raid6: neonx1 xor() 857 MB/s > raid6: int64x8 gen() 985 MB/s > raid6: int64x8 xor() 753 MB/s > raid6: int64x4 gen() 1043 MB/s > raid6: int64x4 xor() 770 MB/s > raid6: int64x2 gen() 684 MB/s > raid6: int64x2 xor() 609 MB/s > raid6: int64x1 gen() 450 MB/s > raid6: int64x1 xor() 446 MB/s > raid6: using algorithm neonx8 gen() 1649 MB/s > raid6: .... xor() 1511 MB/s, rmw enabled > raid6: using neon recovery algorithm > vgaarb: loaded > SCSI subsystem initialized > usbcore: registered new interface driver usbfs > usbcore: registered new interface driver hub > usbcore: registered new device driver usb > media: Linux media interface: v0.10 > videodev: Linux video capture interface: v2.00 > pps_core: LinuxPPS API ver. 1 registered > pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti > <giome...@linux.it> > PTP clock support registered > EDAC MC: Ver: 3.0.0 > zynqmp-ipi-mbox mailbox@ff990400: Registered ZynqMP IPI mbox with TX/RX > channels. > FPGA manager framework > Advanced Linux Sound Architecture Driver Initialized. > clocksource: Switched to clocksource arch_sys_counter > NET: Registered protocol family 2 > tcp_listen_portaddr_hash hash table entries: 2048 (order: 3, 32768 bytes) > TCP established hash table entries: 32768 (order: 6, 262144 bytes) > TCP bind hash table entries: 32768 (order: 7, 524288 bytes) > TCP: Hash tables configured (established 32768 bind 32768) > UDP hash table entries: 2048 (order: 4, 65536 bytes) > UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes) > NET: Registered protocol family 1 > RPC: Registered named UNIX socket transport module. > RPC: Registered udp transport module. > RPC: Registered tcp transport module. > RPC: Registered tcp NFSv4.1 backchannel transport module. > PCI: CLS 0 bytes, default 64 > hw perfevents: no interrupt-affinity property for /pmu, guessing. > hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available > kprobes: failed to populate blacklist: -22 > Please take care of using kprobes. > workingset: timestamp_bits=46 max_order=20 bucket_order=0 > NFS: Registering the id_resolver key type > Key type id_resolver registered > Key type id_legacy registered > Installing knfsd (copyright (C) 1996 o...@monad.swb.de). > jffs2: version 2.2. (NAND) �© 2001-2006 Red Hat, Inc. > Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247) > io scheduler mq-deadline registered > io scheduler kyber registered > io scheduler bfq registered > cacheinfo: Unable to detect cache hierarchy for CPU 0 > brd: module loaded > loop: module loaded > libphy: Fixed MDIO Bus: probed > CAN device driver interface > e1000e: Intel(R) PRO/1000 Network Driver - 3.2.6-k > e1000e: Copyright(c) 1999 - 2015 Intel Corporation. > usbcore: registered new interface driver usb-storage > rtc_zynqmp ffa60000.rtc: registered as rtc0 > i2c /dev entries driver > device-mapper: ioctl: 4.40.0-ioctl (2019-01-18) initialised: > dm-de...@redhat.com > EDAC MC: ECC not enabled > EDAC DEVICE0: Giving out device to module zynqmp-ocm-edac controller > zynqmp_ocm: DEV ff960000.memory-controller (INTERRUPT) > sdhci: Secure Digital Host Controller Interface driver > sdhci: Copyright(c) Pierre Ossman > sdhci-pltfm: SDHCI platform and OF driver helper > zynqmp_firmware_probe Platform Management API v1.1 > zynqmp_firmware_probe Trustzone version v1.0 > zynqmp-pinctrl firmware:zynqmp-firmware:pinctrl: zynqmp pinctrl initialized > zynqmp_clk_mux_get_parent() getparent failed for clock: lpd_wdt, ret = -22 > usbcore: registered new interface driver usbhid > usbhid: USB HID core driver > ARM CCI_400_r1 PMU driver probed > fpga_manager fpga0: Xilinx ZynqMP FPGA Manager registered > usbcore: registered new interface driver snd-usb-audio > u32 classifier > Actions configured > NET: Registered protocol family 10 > Segment Routing with IPv6 > sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver > NET: Registered protocol family 17 > can: controller area network core (rev 20170425 abi 9) > NET: Registered protocol family 29 > can: raw protocol (rev 20170425) > can: broadcast manager protocol (rev 20170425 t) > can: netlink gateway (rev 20170425) max_hops=1 > Key type dns_resolver registered > registered taskstats version 1 > kmemleak: Kernel memory leak detector initialized > kmemleak: Automatic memory scanning thread started > Btrfs loaded, crc32c=crc32c-generic > Key type encrypted registered > �ɥ��ѭ console [ttyPS0] enabledO 0xff000000 (irq = 39, base_baud = 6249999) is > a xuartps > printk: console [ttyPS0] enabled > printk: bootconsole [cdns0] disabled > printk: bootconsole [cdns0] disabled > ff010000.serial: ttyPS1 at MMIO 0xff010000 (irq = 40, base_baud = 6249999) is > a xuartps > of-fpga-region fpga-full: FPGA Region probed > nwl-pcie fd0e0000.pcie: failed to parse reset gpio > nwl-pcie fd0e0000.pcie: fail to reset pcie device > nwl-pcie: probe of fd0e0000.pcie failed with error -2 > xilinx-dpdma fd4c0000.dma: Xilinx DPDMA engine is probed > xilinx-zynqmp-dma fd500000.dma: ZynqMP DMA driver Probe success > xilinx-zynqmp-dma fd510000.dma: ZynqMP DMA driver Probe success > xilinx-zynqmp-dma fd520000.dma: ZynqMP DMA driver Probe success > xilinx-zynqmp-dma fd530000.dma: ZynqMP DMA driver Probe success > xilinx-zynqmp-dma fd540000.dma: ZynqMP DMA driver Probe success > xilinx-zynqmp-dma fd550000.dma: ZynqMP DMA driver Probe success > xilinx-zynqmp-dma fd560000.dma: ZynqMP DMA driver Probe success > xilinx-zynqmp-dma fd570000.dma: ZynqMP DMA driver Probe success > xilinx-psgtr fd400000.zynqmp_phy: Lane:1 type:8 protocol:4 pll_locked:yes > xilinx-dp-snd-codec fd4a0000.zynqmp-display:zynqmp_dp_snd_codec0: Xilinx > DisplayPort Sound Codec probed > xilinx-dp-snd-pcm zynqmp_dp_snd_pcm0: Xilinx DisplayPort Sound PCM probed > xilinx-dp-snd-pcm zynqmp_dp_snd_pcm1: Xilinx DisplayPort Sound PCM probed > xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: > xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok > xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: > xilinx-dp-snd-codec-dai <-> xilinx-dp-snd-codec-dai mapping ok > xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: ASoC: no DMI > vendor name! > xilinx-dp-snd-card fd4a0000.zynqmp-display:zynqmp_dp_snd_card: Xilinx > DisplayPort Sound Card probed > OF: graph: no port node found in /amba/zynqmp-display@fd4a0000 > [drm] Supports vblank timestamp caching Rev 2 (21.10.2013). > [drm] No driver support for vblank timestamp query. > xlnx-drm xlnx-drm.0: bound fd4a0000.zynqmp-display (ops 0xffffff8010d3f078) > [drm] Cannot find any crtc or sizes > [drm] Initialized xlnx 1.0.0 20130509 for fd4a0000.zynqmp-display on minor 0 > zynqmp-display fd4a0000.zynqmp-display: ZynqMP DisplayPort Subsystem driver > probed > xilinx-psgtr fd400000.zynqmp_phy: Lane:3 type:3 protocol:2 pll_locked:yes > ahci-ceva fd0c0000.ahci: AHCI 0001.0301 32 slots 2 ports 6 Gbps 0x3 impl > platform mode > ahci-ceva fd0c0000.ahci: flags: 64bit ncq sntf pm clo only pmp fbs pio slum > part ccc sds apst > scsi host0: ahci-ceva > scsi host1: ahci-ceva > ata1: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x100 irq 37 > ata2: SATA max UDMA/133 mmio [mem 0xfd0c0000-0xfd0c1fff] port 0x180 irq 37 > m25p80 spi0.0: found n25q512a, expected m25p80 > m25p80 spi0.0: n25q512a (131072 Kbytes) > 4 fixed-partitions partitions found on MTD device spi0.0 > Creating 4 MTD partitions on "spi0.0": > 0x000000000000-0x000000100000 : "qspi-fsbl-uboot" > 0x000000100000-0x000000600000 : "qspi-linux" > 0x000000600000-0x000000620000 : "qspi-device-tree" > 0x000000620000-0x000000c00000 : "qspi-rootfs" > macb ff0e0000.ethernet: Not enabling partial store and forward > libphy: MACB_mii_bus: probed > TI DP83867 ff0e0000.ethernet-ffffffff:0c: attached PHY driver [TI DP83867] > (mii_bus:phy_addr=ff0e0000.ethernet-ffffffff:0c, irq=POLL) > macb ff0e0000.ethernet eth0: Cadence GEM rev 0x50070106 at 0xff0e0000 irq 23 > (00:0a:35:00:22:01) > xilinx-axipmon ffa00000.perf-monitor: Probed Xilinx APM > xilinx-axipmon fd0b0000.perf-monitor: Probed Xilinx APM > xilinx-axipmon fd490000.perf-monitor: Probed Xilinx APM > xilinx-axipmon ffa10000.perf-monitor: Probed Xilinx APM > dwc3 fe200000.dwc3: Failed to get clk 'ref': -2 > xilinx-psgtr fd400000.zynqmp_phy: Lane:2 type:0 protocol:3 pll_locked:yes > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 > xhci-hcd xhci-hcd.0.auto: hcc params 0x0238f625 hci version 0x100 quirks > 0x0000001002010810 > xhci-hcd xhci-hcd.0.auto: irq 45, io mem 0xfe200000 > hub 1-0:1.0: USB hub found > hub 1-0:1.0: 1 port detected > xhci-hcd xhci-hcd.0.auto: xHCI Host Controller > xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 > xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed > hub 2-0:1.0: USB hub found > hub 2-0:1.0: 1 port detected > pca953x 0-0020: 0-0020 supply vcc not found, using dummy regulator > GPIO line 496 (sel0) hogged as output/low > GPIO line 497 (sel1) hogged as output/high > GPIO line 498 (sel2) hogged as output/high > GPIO line 499 (sel3) hogged as output/high > pca953x 0-0021: 0-0021 supply vcc not found, using dummy regulator > ina2xx 3-0040: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-0041: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-0042: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-0043: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-0044: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-0045: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-0046: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-0047: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-004a: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 3-004b: power monitor ina226 (Rshunt = 5000 uOhm) > i2c i2c-0: Added multiplexed i2c bus 3 > ina2xx 4-0040: power monitor ina226 (Rshunt = 2000 uOhm) > ina2xx 4-0041: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 4-0042: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 4-0043: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 4-0044: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 4-0045: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 4-0046: power monitor ina226 (Rshunt = 5000 uOhm) > ina2xx 4-0047: power monitor ina226 (Rshunt = 5000 uOhm) > i2c i2c-0: Added multiplexed i2c bus 4 > ata2: SATA link down (SStatus 0 SControl 330) > ata1: SATA link down (SStatus 0 SControl 330) > max20751 5-0072: PMBus status register not found > max20751 5-0073: PMBus status register not found > i2c i2c-0: Added multiplexed i2c bus 5 > i2c i2c-0: Added multiplexed i2c bus 6 > pca954x 0-0075: registered 4 multiplexed busses for I2C mux pca9544 > cdns-i2c ff020000.i2c: 400 kHz mmio ff020000 irq 25 > at24 7-0054: 1024 byte 24c08 EEPROM, writable, 1 bytes/write > i2c i2c-1: Added multiplexed i2c bus 7 > i2c i2c-1: Added multiplexed i2c bus 8 > si570 9-005d: registered, current frequency 300000000 Hz > i2c i2c-1: Added multiplexed i2c bus 9 > si570 10-005d: registered, current frequency 148500000 Hz > i2c i2c-1: Added multiplexed i2c bus 10 > si5324 11-0069: si5328 probed > si5324 11-0069: si5328 probe successful > i2c i2c-1: Added multiplexed i2c bus 11 > i2c i2c-1: Added multiplexed i2c bus 12 > i2c i2c-1: Added multiplexed i2c bus 13 > i2c i2c-1: Added multiplexed i2c bus 14 > pca954x 1-0074: registered 8 multiplexed busses for I2C switch pca9548 > i2c i2c-1: Added multiplexed i2c bus 15 > i2c i2c-1: Added multiplexed i2c bus 16 > i2c i2c-1: Added multiplexed i2c bus 17 > i2c i2c-1: Added multiplexed i2c bus 18 > i2c i2c-1: Added multiplexed i2c bus 19 > i2c i2c-1: Added multiplexed i2c bus 20 > i2c i2c-1: Added multiplexed i2c bus 21 > i2c i2c-1: Added multiplexed i2c bus 22 > pca954x 1-0075: registered 8 multiplexed busses for I2C switch pca9548 > cdns-i2c ff030000.i2c: 400 kHz mmio ff030000 irq 26 > cdns-wdt fd4d0000.watchdog: Xilinx Watchdog Timer at (____ptrval____) with > timeout 60s > mmc0: SDHCI controller on ff170000.mmc [ff170000.mmc] using ADMA 64-bit > printk: console [netcon0] enabled > netconsole: network logging started > input: gpio-keys as /devices/platform/gpio-keys/input/input0 > rtc_zynqmp ffa60000.rtc: setting system clock to 2013-12-01T11:36:48 UTC > (1385897808) > random: fast init done > pps pps0: new PPS source ptp0 > mmc0: new high speed SDHC card at address 0007 > macb ff0e0000.ethernet: gem-ptp-timer ptp clock registered. > mmcblk0: mmc0:0007 SS16G 14.5 GiB > mmcblk0: p1 p2 > [drm] Cannot find any crtc or sizes > macb ff0e0000.ethernet eth0: link up (1000/Full) > IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready > IP-Config: Complete: > device=eth0, hwaddr=00:0a:35:00:22:01, ipaddr=128.224.163.14, > mask=255.254.0.0, gw=128.224.162.1 > host=128.224.163.14, domain=, nis-domain=(none) > bootserver=128.224.162.137, rootserver=128.224.162.137, rootpath= > clk: Not disabling unused clocks > ALSA device list: > #0: DisplayPort monitor > md: Waiting for all devices to be available before autodetect > md: If you don't use raid, use raid=noautodetect > md: Autodetecting RAID arrays. > md: autorun ... > md: ... autorun DONE. > VFS: Mounted root (nfs filesystem) on device 0:19. > devtmpfs: mounted > Freeing unused kernel memory: 2112K > Run /sbin/init as init process > systemd[1]: System time before build time, advancing clock. > systemd[1]: systemd 242-19-gdb2e367+ running in system mode. (+PAM -AUDIT > -SELINUX +IMA -APPARMOR +SMACK +SYSVINIT +UTMP -LIBCRYPTSETUP -GCRYPT -GNUTL) > systemd[1]: Detected architecture arm64. > > Welcome to Wind River Linux > development_linux-yocto-dev_userspace-next_toolchain-next 19.27! > > systemd[1]: Set hostname to <xilinx-zynqmp>. > systemd[1]: Failed to bump fs.file-max, ignoring: Invalid argument > systemd[1]: /lib/systemd/system/dbus.socket:4: ListenStream= references a > path below legacy directory /var/run/, updating /var/run/dbus/system_bus_soc. > systemd[1]: /lib/systemd/system/rpcbind.socket:4: ListenStream= references a > path below legacy directory /var/run/, updating /var/run/rpcbind.sock ��→. > random: systemd: uninitialized urandom read (16 bytes read) > systemd[1]: Listening on udev Kernel Socket. > [ OK ] Listening on udev Kernel Socket. > random: systemd: uninitialized urandom read (16 bytes read) > systemd[1]: Listening on Journal Socket. > [ OK ] Listening on Journal Socket. > random: systemd: uninitialized urandom read (16 bytes read) > systemd[1]: Mounting Huge Pages File System... > Mounting Huge Pages File System... > systemd[1]: Started Dispatch Password Requests to Console Directory Watch. > [ OK ] Started Dispatch Password ��…ts to Console Directory Watch. > [ OK ] Reached target Swap. > [ OK ] Created slice User and Session Slice. > [ OK ] Reached target Slices. > [ OK ] Listening on initctl Compatibility Named Pipe. > [ OK ] Listening on udev Control Socket. > Starting udev Coldplug all Devices... > Mounting Kernel Debug File System... > [ OK ] Listening on Syslog Socket. > Starting Create list of re��…odes for the current kernel... > [ OK ] Reached target Remote File Systems. > Mounting POSIX Message Queue File System... > [ OK ] Listening on Network Service Netlink Socket. > [ OK ] Created slice system-getty.slice. > Mounting Temporary Directory (/tmp)... > [ OK ] Created slice system-serial\x2dgetty.slice. > Starting Load Kernel Modules... > [ OK ] Started Forward Password R��…uests to Wall Directory Watch. > [ OK ] Reached target Paths. > Starting Remount Root and Kernel File Systems... > [ OK ] Listening on Journal Socket (/dev/loopenvswitch: Open vSwitch > switching datapath > g). > Starting Journal Service... > [ OK ] Mounted Huge Pages File System. > [ OK ] Mounted Kernel Debug File System. > [ OK ] Started Create list of req��… nodes for the current kernel. > [ OK ] Mounted POSIX Message Queue File System. > [ OK ] Mounted Temporary Directory (/tmp). > [ OK ] Started Load Kernel Modules. > [ OK ] Started Remount Root and Kernel File Systems. > Mounting NFSD configuration filesystem... > Starting Apply Kernel Variables... > Starting Create Static Device Nodes in /dev... > [ OK ] Started Journal Service. > [ OK ] Mounted NFSD configuration filesystem. > [ OK ] Started Apply Kernel Variables. > Starting Flush Journal to Persistent Storage... > [ OK ] Started Create Static Device Nodes in /dev. > [ OK ] Reached target Local File Systems (Pre). > Mounting /var/volatile... > Starting udev Kernel Device Manager... > [ OK ] Mounted /var/volatile. > Starting Load/Save Random Seed... > [ OK ] Reached target Local File Systems. > systemd-journald[164]: Received request to flush runtime journal from PID 1 > [ OK ] Started Flush Journal to Persistent Storage. > Starting Create Volatile Files and Directories... > [ OK ] Started udev Coldplug all Devices. > [ OK ] Started udev Kernel Device Manager. > [ OK ] Started Load/Save Random Seed. > Starting Network Service... > mali: loading out-of-tree module taints kernel. > [ OK ] Started Network Service. > [ OK ] Started Create Volatile Files and Directories. > [ OK ] Found device /dev/ttyPS0. > [ OK ] Listening on Load/Save RF ��…itch Status /dev/rfkill Watch. > Starting Network Name Resolution... > Starting Update UTMP about System Boot/Shutdown... > random: crng init done > random: 7 urandom warning(s) missed due to ratelimiting > Starting Network Time Synchronization... > [ OK ] Started Update UTMP about System Boot/Shutdown. > [ OK ] Started Network Name Resolution. > [ OK ] Started Network Time Synchronization. > [ OK ] Reached target System Time Set. > [ OK ] Reached target System Time Synchronized. > [ OK ] Reached target System Initialization. > [ OK ] Started Daily Cleanup of Temporary Directories. > [ OK ] Started Daily rotation of log files. > [ OK ] Reached target Timers. > [ OK ] Listening on D-Bus System Message Bus Socket. > [ OK ] Listening on Avahi mDNS/DNS-SD Stack Activation Socket. > Starting Console System Startup Logging... > Starting sshd.socket. > Starting Reboot and dump vmcore via kexec... > [ OK ] Listening on RPCbind Server Activation Socket. > [ OK ] Started Console System Startup Logging. > [ OK ] Listening on sshd.socket. > [ OK ] Started Reboot and dump vmcore via kexec. > [ OK ] Reached target Sockets. > [ OK ] Reached target Basic System. > [ OK ] Started D-Bus System Message Bus. > [ OK ] Started Xserver startup without a display manager. > [ OK ] Started Dynamic Host Configuration Protocol (DHCP). > [ OK ] Reached target Network. > Starting Postfix Mail Transport Agent... > Starting RPC Bind Service... > [ OK ] Started irqbalance daemon. > Starting /etc/rc.local Compatibility... > Starting System Logging Service... > Starting Telephony service... > [ OK ] Started Periodic Command Scheduler. > Starting Login Service... > Starting Target Communication Framework agent... > Starting Berkeley Internet Name Domain (DNS)... > Starting Avahi mDNS/DNS-SD Stack... > [ OK ] Started Job spooling tools. > Starting Save/Restore Sound Card State... > Starting Permit User Sessions... > [ OK ] Started System Logging Service. > [ OK ] Started RPC Bind Service. > [ OK ] Started /etc/rc.local Compatibility. > [ OK ] Started Target Communication Framework agent. > [ OK ] Started Save/Restore Sound Card State. > [ OK ] Started Permit User Sessions. > [ OK ] Reached target Sound Card. > [ OK ] Started Getty on tty1. > [ OK ] Started Serial Getty on ttyPS0. > [ OK ] Started Login Service. > [ OK ] Started Telephony service. > [ OK ] Started Avahi mDNS/DNS-SD Stack. > [ OK ] Started Berkeley Internet Name Domain (DNS). > [ OK ] Reached target Host and Network Name Lookups. > [ OK ] Started NFS status monitor for NFSv2/3 locking.. > [ OK ] Started Postfix Mail Transport Agent. > > Wind River Linux development_linux-yocto-dev_userspace-next_toolchain-next > 19.29 xilinx-zynqmp ttyPS0 > > xilinx-zynqmp login: > xilinx-zynqmp login: root > Password: > root@xilinx-zynqmp:~# uname -a > Linux xilinx-zynqmp 5.2.0-yoctodev-standard #139 SMP PREEMPT Mon Jul 22 > 18:18:00 CST 2019 aarch64 aarch64 aarch64 GNU/Linux > > > Quanyang Wang (1): > xilinx-zynqmp: enable kernel options for SDK xlnx_rebase_v4.19 > > bsp/xilinx-zynqmp/xilinx-zynqmp.cfg | 76 +++++++++++++++++++++++++++++ > bsp/xilinx-zynqmp/xilinx-zynqmp.scc | 1 + > 2 files changed, 77 insertions(+) > > -- > 2.17.1 > -- - Thou shalt not follow the NULL pointer, for chaos and madness await thee at its end - "Use the force Harry" - Gandalf, Star Trek II -- _______________________________________________ linux-yocto mailing list linux-yocto@yoctoproject.org https://lists.yoctoproject.org/listinfo/linux-yocto
