J'ajoute à mon mail précédent le log de dmesg à la fin du boot (meme après reset du BIOS pour PnP OS sur off, ca marche pas nondidju):
Linux PCMCIA Card Services 3.2.3 kernel build: 2.4.18-bf2.4 #1 Son Apr 14 09:53:28 CEST 2002 options: [pci] [cardbus] [apm] [pnp] PnP: PNP BIOS installation structure at 0xc00fc430 PnP: PNP BIOS version 1.0, entry at f0000:c4bc, dseg at f0000 Intel ISA/PCI/CardBus PCIC probe: PCI: Enabling device 00:11.0 (0000 -> 0002) TI 1410 rev 01 PCI-to-CardBus at slot 00:11, mem 0x10000000 host opts [0]: [serial pci & irq] [pci irq 9] [lat 32/176] [bus 1/4] PCI irq 9 test failed ISA irqs (scanned) = none!<6> *NO* card interrupts, polling interval = 1000 ms cs: memory probe 0xa0000000-0xa0ffffff: clean. hostap_crypt: registered algorithm 'NULL' hostap_cs: hostap_cs.c 0.0.0 2002-10-12 (SSH Communications Security Corp, Jouni Malinen) hostap_cs: (c) Jouni Malinen <[EMAIL PROTECTED]> hostap_cs: CardServices release does not match! hostap_crypt: unregistered algorithm 'NULL' (deinit) On Thu, 7 Nov 2002 23:37:55 +0100 Vincent JAMART <[EMAIL PROTECTED]> wrote: > Salut la liste > > J'ai un souci avec une ZoomAir 4105 (4103 dans un adaptateur PLX), Prism 2.5. > *Debian Woody, 2.4.18-bf2.4 avec headers, hostap-2002-10_12 et PCMCIA-CS de woody. > > (La PCMCIA seule fonctionne dans le laptop en mode AD-HOC et AP, donc ce n'est pas >un prbl. de flash release) > > Deux cas de figure: > > 1) J'applique la procédure PLX de Jouri: make plx, make install_plx, je retire >pcmcia-cs et rmmod des modules pcmcia loadés: modprobe -v hostap_plx =>erreur >d'IRQ/IO et card not found, comme suit: > > benten:/LOG# modprobe hostap_crypt > benten:/LOG# modprobe hostap > benten:/LOG# modprobe hostap_plx/lib/modules/2.4.18-bf2.4/net/hostap_plx.o: >init_module: No such device > Hint: insmod errors can be caused by incorrect module parameters, including invalid >IO or IRQ parameters > /lib/modules/2.4.18-bf2.4/net/hostap_plx.o: insmod >/lib/modules/2.4.18-bf2.4/net/hostap_plx.o failed > /lib/modules/2.4.18-bf2.4/net/hostap_plx.o: insmod hostap_plx failed > > > 2) Je configure hostap avec hostap_cs, pas de prob. depmod. La carte PLX est >reconnue par le kernel comme une Texas Instruments PCI1410. Ensuite je fais un >modprobe de hostap_cs: il load les modules (hostap_crypt, hostap et hostap_cs) mais >me renvoie une erreur I/O et IRQ. > > Il me reste deux choses à faire: > Soit reset du bios pour désactiver le PnP (j'ai pas le password 8-/ ) mais j'ai un >doute: la SB16 et les 2 RTL-8139 marchent très bien alors que c'est aussi du PnP. > C'est fait, je force les IRQ mais ca ne change RIEN (sur la 9 et 10, f.i.) > Alex, quelle était ta procédure sous Linux (puisque OpenBSD ct un autre PLX)? > > L'alternative Die-Hard: comme décrit sur >http://hostap.epitest.fi/hostap/2002-09/1981.html et README.Prism2 , modifier les >sources de hostap_plx.c et y ajouter le chipset TI PCI-1410 et son device ID (je le >trouvz où dans lspci?) ou j'évite la fonction manfid > (quid: le type PLX9052 est-il un chipset ou une norme???). > > REM: Chose 1/2 curieuse, le chipset PCMCIA de mon laptop est un TI PCI-1211, et >dessus aucun problème pour loader hostap_cs avec la 4103 livrée dans le PLX. Bcp de >modifications avec le PCI-1410, si infos? > > LOGS, au boot: > > #lspci -vv de la carte PLX (pas d'IRQ partagé sur un autre device): > 00:11.0 CardBus bridge: Texas Instruments PCI1410 PC card Cardbus Controller (re > v 01) > Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Step > ping- SERR- FastB2B- > Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort > - <MAbort- >SERR- <PERR- > Latency: 32, cache line size 08 > Interrupt: pin A routed to IRQ 12 /*changé en IRQ 9 à présent */ > Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K] > Bus: primary=00, secondary=01, subordinate=04, sec-latency=176 > I/O window 0: 00000000-00000003 > I/O window 1: 00000000-00000003 > BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+ > 16-bit legacy interface ports at 0001 > > #cardctl ident: > Socket 0: > product info: "ZoomAir 11Mbps High", "Rate wireless Networking", "", "" > manfid: 0x0156, 0x0002 > function: 6 (network) > > dmesg après un cardctl: > Nov 7 23:35:58 benten kernel: hostap_crypt: registered algorithm 'NULL' > Nov 7 23:35:59 benten kernel: hostap_cs: hostap_cs.c 0.0.0 2002-10-12 (SSH Comm > unications Security Corp, Jouni Malinen) > Nov 7 23:35:59 benten kernel: hostap_cs: (c) Jouni Malinen <[EMAIL PROTECTED]> > Nov 7 23:35:59 benten kernel: hostap_cs: CardServices release does not match! > Nov 7 23:35:59 benten kernel: hostap_crypt: unregistered algorithm 'NULL' (deinit) > > et lsmod: > Module Size Used by Not tainted > ds 6624 1 > i82365 22608 1 > pcmcia_core 47104 0 [ds i82365] > sym53c416 6432 0 (unused) > lp 6912 0 (unused) > sb 7328 0 (unused) > sb_lib 32256 0 [sb] > uart401 6016 0 [sb_lib] > sound 52876 0 [sb_lib uart401] > soundcore 3236 4 [sb_lib sound] > isa-pnp 27432 0 [sym53c416 sb] > ipt_tos 480 0 (unused) > iptable_mangle 2112 0 (unused) > iptable_filter 1728 0 (unused) > ipt_REJECT 2816 0 (unused) > ipt_MASQUERADE 1216 0 (unused) > ipt_MARK 736 0 (unused) > ipt_LOG 3136 0 (unused) > ip_queue 5156 0 (unused) > ip_nat_irc 2368 0 (unused) > ip_nat_ftp 2944 0 (unused) > iptable_nat 12660 2 [ipt_MASQUERADE ip_nat_irc ip_nat_ftp] > ip_tables 10432 10 [ipt_tos iptable_mangle iptable_filter ipt_REJ > ECT ipt_MASQUERADE ipt_MARK ipt_LOG iptable_nat] > ip_conntrack_irc 2496 0 (unused) > ip_conntrack_ftp 3200 0 (unused) > ip_conntrack 12684 3 [ipt_MASQUERADE ip_nat_irc ip_nat_ftp iptable_ > nat ip_conntrack_irc ip_conntrack_ftp] > parport_pc 25704 1 > parport 21728 1 [lp parport_pc] > -- Vincent Jamart DBA/UNIX System Engineer phone: +32-495/21.22.58 +352-91/88.00.73 mail: [EMAIL PROTECTED] GnuPG 1D62 07D4 F8E8 746B E043 D04C A77C 64C0 56CC CC26 --------------------------------- "Proprietary data is the root of tyranny" -- Britt Blaser
msg07306/pgp00000.pgp
Description: PGP signature