Same here - ES40's, DS20's, and DS10L's. Great work, Eric.
Jim
On Tue, 6 Feb 2001, Carr, Bill wrote:
> Hi Eric.
>
> Great news!!!!
>
> We have a DS20 at our disposal. We want to get your stuff working on the
> DS20. Could you tar up and send us what you have as you offered in your
> last message?
>
> Thanks,
>
> Bill and Phil.
>
>
>
> -----Original Message-----
> From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]]
> Sent: Tuesday, February 06, 2001 12:55 AM
> To: [EMAIL PROTECTED]
> Cc: LinuxBIOS; Ronald G Minnich; Jim Garlick; Jeremy Jackson; Carr,
> Bill; Ezolt, Phillip
> Subject: Yahoo!!! linuxbios Boots on alpha DS10
>
>
>
> O.k. After adding the code to properly initialize the i8259 interrupt
> controller, and the RTC, linux Boots!
>
> On the alpha with 2.4.0 I don't even need to touch the PCI bus.
>
> The only detail still waiting is how to enable writing to the flash
> chip over the TIG bus.
>
> For reference I have not needed to pull the 2MB AMD flash rom from
> my system, despite the fact I made certain it was possible.
>
> Eric
>
> ---- boot log ---------
> testboot 1
> RTC_FREQ_SELECT=0x27
> RTC_CONTROL =0x46
> RTC_INTR_FLAGS =0xd0
> RTC_VALID =0x80
> Setting RTC_FREQ to 1024 Hz (27)
> Turning on square wave RTC interrupts.
>
> Welcome to start32, the open sourced starter.
> This space will eventually hold more diagnostic information.
>
> January 2000, James Hendricks, Dale Webster, and Ron Minnich.
> Version 0.1
>
> Linux version 2.4.0.dp264.eb1.4 (eric@ds10) (gcc version egcs-2.91.66
> 19990314/Linux (egcs-1.1.2 release)) #17 Mon Feb 5 22:27:22 MST 2001
> UBE pointer: 0x000000000000bfd0
> Ok, code 0
> (rev 0)
> pcb->ksp= 0xfffffc00004bfed0
> pcb->usp= 0x0000000000000000
> pcb->ptbr= 0x0000000000000180
> pcb->pcc= 0x0000000000000000
> pcb->asn= 0x0000000000000000
> pcb->unique=0x0000000000000000
> pcb->flags= 0x0000000000000001
> pcb->res1= 0x0000000000000000
> pcb->res2= 0x0000000000000000
> hwpcb:
> pcb->ksp= 0x0000000000000000
> pcb->usp= 0x0000000000000000
> pcb->ptbr= 0x0000000000000000
> pcb->pcc= 0x0000000000000000
> pcb->asn= 0x0000000000000000
> pcb->unique=0x0000000000000000
> pcb->flags= 0x0000000000000000
> pcb->res1= 0x0000000000000000
> pcb->res2= 0x0000000000000000
> Booting GENERIC on Tsunami variation Webbrick using machine vector Webbrick
> from MILO
> Command line: console=ttyS0,9600 root=/dev/sda2 1
> memcluster 0, usage 1, start 0, end 128
> memcluster 1, usage 0, start 128, end 16384
> freeing pages 128:384
> freeing pages 709:16384
> tsunami_init_arch: CChip registers:
> tsunami_init_arch: CSR_CSC 0x42444015152664
> tsunami_init_arch: CSR_MTR 0x2f7414000130
> tsunami_init_arch: CSR_MISC 0x110000030
> tsunami_init_arch: CSR_DIM0 0x0
> tsunami_init_arch: CSR_DIM1 0x0
> tsunami_init_arch: CSR_DIR0 0x0
> tsunami_init_arch: CSR_DIR1 0x0
> tsunami_init_arch: CSR_DRIR 0x83c0000000000000
> tsunami_init_arch: CSR_TTR 0x3103
> tsunami_init_arch: CSR_TDR 0xf37ff37ff37ff37f
> tsunami_init_arch: DChip registers:
> tsunami_init_arch: CSR_DSC 0x404040404040404
> tsunami_init_arch: CSR_STR 0x2626262626262626
> tsunami_init_arch: CSR_DREV 0x101010101010101
> On node 0 totalpages: 16384
> zone(0): 16384 pages.
> zone(1): 0 pages.
> zone(2): 0 pages.
> Kernel command line: console=ttyS0,9600 root=/dev/sda2 1
> Using epoch = 1900
> RTC_FREQ_SELECT = 0x26
> Linux version 2.4.0.dp264.eb1.4 (eric@ds10) (gcc version egcs-2.91.66
> 19990314/Linux (egcs-1.1.2 release)) #17 Mon Feb 5 22:27:22 MST 2001
> UBE pointer: 0x000000000000bfd0
> Ok, code 0
> (rev 0)
> pcb->ksp= 0xfffffc00004bfed0
> pcb->usp= 0x0000000000000000
> pcb->ptbr= 0x0000000000000180
> pcb->pcc= 0x0000000000000000
> pcb->asn= 0x0000000000000000
> pcb->unique=0x0000000000000000
> pcb->flags= 0x0000000000000001
> pcb->res1= 0x0000000000000000
> pcb->res2= 0x0000000000000000
> hwpcb:
> pcb->ksp= 0x0000000000000000
> pcb->usp= 0x0000000000000000
> pcb->ptbr= 0x0000000000000000
> pcb->pcc= 0x0000000000000000
> pcb->asn= 0x0000000000000000
> pcb->unique=0x0000000000000000
> pcb->flags= 0x0000000000000000
> pcb->res1= 0x0000000000000000
> pcb->res2= 0x0000000000000000
> Booting GENERIC on Tsunami variation Webbrick using machine vector Webbrick
> from MILO
> Command line: console=ttyS0,9600 root=/dev/sda2 1
> memcluster 0, usage 1, start 0, end 128
> memcluster 1, usage 0, start 128, end 16384
> freeing pages 128:384
> freeing pages 709:16384
> tsunami_init_arch: CChip registers:
> tsunami_init_arch: CSR_CSC 0x42444015152664
> tsunami_init_arch: CSR_MTR 0x2f7414000130
> tsunami_init_arch: CSR_MISC 0x110000030
> tsunami_init_arch: CSR_DIM0 0x0
> tsunami_init_arch: CSR_DIM1 0x0
> tsunami_init_arch: CSR_DIR0 0x0
> tsunami_init_arch: CSR_DIR1 0x0
> tsunami_init_arch: CSR_DRIR 0x83c0000000000000
> tsunami_init_arch: CSR_TTR 0x3103
> tsunami_init_arch: CSR_TDR 0xf37ff37ff37ff37f
> tsunami_init_arch: DChip registers:
> tsunami_init_arch: CSR_DSC 0x404040404040404
> tsunami_init_arch: CSR_STR 0x2626262626262626
> tsunami_init_arch: CSR_DREV 0x101010101010101
> On node 0 totalpages: 16384
> zone(0): 16384 pages.
> zone(1): 0 pages.
> zone(2): 0 pages.
> Kernel command line: console=ttyS0,9600 root=/dev/sda2 1
> Using epoch = 1900
> RTC_FREQ_SELECT = 0x26
> Calibrating delay loop... 919.28 BogoMIPS
> Memory: 125104k/131072k available (1481k kernel code, 4944k reserved, 473k
> data, 168k init)
> Dentry-cache hash table entries: 16384 (order: 5, 262144 bytes)
> Buffer-cache hash table entries: 8192 (order: 3, 65536 bytes)
> Page-cache hash table entries: 16384 (order: 4, 131072 bytes)
> Inode-cache hash table entries: 8192 (order: 4, 131072 bytes)
> POSIX conformance testing by UNIFIX
> got res[8000:80ff] for resource 0 of PCI device 1077:1020
> got res[8400:847f] for resource 0 of PCI device 1011:0019
> got res[8480:84ff] for resource 0 of PCI device 1011:0019
> got res[8800:880f] for resource 0 of PCI device 10b9:5229
> got res[8810:881f] for resource 2 of PCI device 10b9:5229
> got res[8820:882f] for resource 4 of PCI device 10b9:5229
> got res[8830:8833] for resource 1 of PCI device 10b9:5229
> got res[8834:8837] for resource 3 of PCI device 10b9:5229
> got res[9000000:97fffff] for resource 1 of PCI device 104c:3d07
> got res[9800000:9ffffff] for resource 2 of PCI device 104c:3d07
> got res[a000000:a03ffff] for resource 6 of PCI device 1011:0019
> got res[a040000:a07ffff] for resource 6 of PCI device 1011:0019
> got res[a080000:a09ffff] for resource 0 of PCI device 104c:3d07
> got res[a0a0000:a0affff] for resource 6 of PCI device 1077:1020
> got res[a0b0000:a0bffff] for resource 6 of PCI device 104c:3d07
> got res[a0c0000:a0c0fff] for resource 0 of PCI device 10b9:5237
> got res[a0c1000:a0c1fff] for resource 1 of PCI device 1077:1020
> got res[a0c2000:a0c23ff] for resource 1 of PCI device 1011:0019
> got res[a0c3000:a0c33ff] for resource 1 of PCI device 1011:0019
> PCI enable device: (PCI device 10b9:5237)
> cmd reg 0x6
> PCI enable device: (PCI device 10b9:1533)
> cmd reg 0xf
> PCI enable device: (PCI device 1011:0019)
> cmd reg 0x7
> PCI enable device: (PCI device 1011:0019)
> cmd reg 0x7
> PCI enable device: (PCI device 10b9:5229)
> cmd reg 0x5
> PCI enable device: (PCI device 1077:1020)
> cmd reg 0x7
> PCI enable device: (PCI device 104c:3d07)
> cmd reg 0x7
> Linux NET4.0 for Linux 2.4
> Based upon Swansea University Computer Society NET3.039
> Starting kswapd v1.8
> pty: 256 Unix98 ptys configured
> Uniform Multi-Platform E-IDE driver Revision: 6.31
> ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
> hda: QUANTUM FIREBALL EX6.4A, ATA DISK drive
> hdd: COMPAQ CDR-8435, ATAPI CDROM drive
> ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
> ide1: unexpected interrupt, status=0xff, count=1
> ide1 at 0x170-0x177,0x376 on irq 15
> hda: 12594960 sectors (6449 MB) w/418KiB Cache, CHS=13328/15/63
> Partition check:
> hda: [PTBL] [784/255/63] hda1 hda2 hda3
> Floppy drive(s): fd0 is 2.88M
> floppy0: no floppy controllers found
> Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI
> enabled
> ttyS00 at 0x03f8 (irq = 4) is a 16550A
> Linux Tulip driver version 0.9.13 (January 2, 2001)
> eth0: Digital DS21143 Tulip rev 65 at 0x8400, 08:00:2B:86:57:E3, IRQ 29.
> eth0: EEPROM default media type Autosense.
> eth0: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)
> block.
> eth0: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2)
> block.
> eth0: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4)
> block.
> eth0: Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (4)
> block.
> eth1: Digital DS21143 Tulip rev 65 at 0x8480, 08:00:2B:86:57:23, IRQ 30.
> eth1: EEPROM default media type Autosense.
> eth1: Index #0 - Media 10baseT (#0) described by a 21142 Serial PHY (2)
> block.
> eth1: Index #1 - Media 10baseT-FD (#4) described by a 21142 Serial PHY (2)
> block.
> eth1: Index #2 - Media 100baseTx (#3) described by a 21143 SYM PHY (4)
> block.
> eth1: Index #3 - Media 100baseTx-FD (#5) described by a 21143 SYM PHY (4)
> block.
> SCSI subsystem driver Revision: 1.00
> qlogicisp : new isp1020 revision ID (5)
> scsi0 : QLogic ISP1020 SCSI on PCI bus 00 device 70 irq 35 I/O base 0x8000
> Vendor: DEC Model: RZ2DA-KA (C) DEC Rev: N1H1
> Type: Direct-Access ANSI SCSI revision: 02
> scsi1 : SCSI host adapter emulation for IDE ATAPI devices
> Vendor: COMPAQ Model: CDR-8435 Rev: 0013
> Type: CD-ROM ANSI SCSI revision: 02
> Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
> SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB)
> sda: sda1 sda2 sda3
> Detected scsi CD-ROM sr0 at scsi1, channel 0, id 0, lun 0
> sr0: scsi3-mmc drive: 32x/32x cd/rw xa/form2 cdda tray
> Uniform CD-ROM driver Revision: 3.12
> flash chip on the Tsunami TIG bus: Found no CFI device at location zero
> mtd: did not recognize jedec chip
> mtd: Giving out device 0 to flash chip on the Tsunami TIG bus
> NET4: Linux TCP/IP 1.0 for NET4.0
> IP Protocols: ICMP, UDP, TCP
> IP: routing cache hash table of 1024 buckets, 16Kbytes
> TCP: Hash tables configured (established 8192 bind 8192)
> NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing unused kernel memory: 168k freed
> INIT: version 2.77 booting
> Welcome to Red Hat Linux
> Press 'I' to enter interactive startup.
>
