> I seem to have a problem when trying to use a lzma pre-compressed payload > in > buildrom in combination with an etherboot (or filo) payload. Things work > fine > with a kernel or LAB payload. > > I've attached the LinuxBIOS Config.lb I used, and the boot output for > etherboot. I recall having similar problems with a filo payload. > > If I disable CONFIG_COMPRESSED_PAYLOAD_LZMA and > CONFIG_PRECOMPRESSED_PAYLOAD > in Config.lb and disable the LZMA compression in buildrom's kconfig the > Etherboot payload works just fine.
I just tried it with serengeti_cheetah, and it worked for me with just a fallback image. I've attached my Config and bootlog. I noticed that you have CONFIG_COMPRESSED_PAYLOAD_LZMA and CONFIG_PRECOMPRESSED_PAYLOAD set in your Failover image, even though there is no official payload. I couldn't see anything else, but I hope this helps. Myles
Config.filoLZMA.lb
Description: Binary data
LinuxBIOS-2.0.0_serengenti_cheetah_Fallback Thu Nov 15 13:03:09 MST 2007
starting...
*sysinfo range: [000cf000,000cf730)
bsp_apicid=00
01 nodes initialized.
core0 started:
started ap apicid:
SBLink=00
NC node|link=00
Ram1.00
Ram2.00
Registered
200Mhz
RAM: 0x00040000 KB
Ram3
Initializing memory: done
set DQS timing:RcvrEn:Pass1: 00 done
set DQS timing:DQSPos: 00 done
set DQS timing:RcvrEn:Pass2: 00 done
Total DQS Training : tsc [00]=000000000192427d
Total DQS Training : tsc [01]=0000000001c17da8
Total DQS Training : tsc [02]=00000000020e4f48
Total DQS Training : tsc [03]=000000000243c3a8
Ram4
v_esp=000cefc8
testx = 5a5a5a5a
Copying data from cache to RAM -- switching to use RAM as stack... Done
testx = 5a5a5a5a
Disabling cache as ram now
Clearing initial memory region: Done
Copying LinuxBIOS to RAM.
src=fffe6000
dst=00100000
linxbios_ram.nrv2b length = 0000f4de
linxbios_ram.bin length = 00026f4c
Jumping to LinuxBIOS.
LinuxBIOS-2.0.0_serengenti_cheetah_Fallback Thu Nov 15 13:03:09 MST 2007
booting...
Enumerating buses...
APIC_CLUSTER: 0 enabled
PCI_DOMAIN: 0000 enabled
PCI: 00:18.3 siblings=0
Found Rev E or Rev F later single core
CPU: APIC: 00 enabled
PCI: pci_scan_bus for bus 00
PCI: 00:18.0 [1022/1100] enabled
PCI: 00:18.1 [1022/1101] enabled
PCI: 00:18.2 [1022/1102] enabled
PCI: 00:18.3 [1022/1103] enabled
----------8<-------Snip----->8---------
Adjust rom_table_end from 0x000f2400 to 0x00100000
Wrote linuxbios table at: 00000530 - 00000dfc checksum 801f
Welcome to elfboot, the open sourced starter.
January 2002, Eric Biederman.
Version 1.3
rom_stream: 0xfff00000 - 0xfffe5fff
Uncompressing to RAM 0x01000000 olen = 0x0000eb68 done.
Found ELF candidate at offset 0
header_offset is 0
Try to load at offset 0x0
New segment addr 0x100000 size 0x2d580 offset 0xc0 filesize 0xe868
(cleaned up) New segment addr 0x100000 size 0x2d580 offset 0xc0 filesize 0xe868
New segment addr 0x12d580 size 0x48 offset 0xe940 filesize 0x48
(cleaned up) New segment addr 0x12d580 size 0x48 offset 0xe940 filesize 0x48
Dropping non PT_LOAD segment
Dropping non PT_LOAD segment
Loading Segment: addr: 0x000000000ff24000 memsz: 0x000000000002d580 filesz:
0x000000000000e868
Clearing Segment: addr: 0x000000000ff32868 memsz: 0x000000000001ed18
Loading Segment: addr: 0x000000000ff51580 memsz: 0x0000000000000048 filesz:
0x0000000000000048
Jumping to boot code at 0x10a2b0
FILO version 0.5 ([EMAIL PROTECTED]) Thu Nov 1 08:23:45 MST 2007
menu: hda1:/boot/filo/menu.lst
hda: LBA48 4295MB: Advanced Micro Devices HDD Device.
Mounted fat
File not found
Press any key to continue.
Press any key to continue.
Press any key to continue.
-- linuxbios mailing list [email protected] http://www.linuxbios.org/mailman/listinfo/linuxbios
