Hi I have a ASUS CUSI-FX board which i would like to build linuxbios for.
If have replaced the onboard flash chip with a plcc socket i just have to
connect the a18 line to the super io chip
The board has a ITE8705 super io chip is this supported or will i have to
add support myself, I do have the data sheet so that shouldn't be that hard.
Where should i place my code in the source tree.
Also the IRQ routing stuff frighterns the hell out of me, could some one
please give me a little help with it.
Russell
output from lspci -vvv
00:00.0 Host bridge: Silicon Integrated Systems [SiS] 630 Host (rev 21)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort+ >SERR- <PERR-
Latency: 32 set
Region 0: Memory at ec000000 (32-bit, non-prefetchable) [size=64M]
Capabilities: [c0] AGP version 2.0
Status: RQ=31 SBA+ 64bit- FW- Rate=421
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
00:00.1 IDE interface: Silicon Integrated Systems [SiS] 5513 [IDE] (rev d0)
(prog-if 80 [Master])
Subsystem: Asustek Computer, Inc.: Unknown device 8035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 128 set
Region 4: I/O ports at d800 [size=16]
00:01.0 ISA bridge: Silicon Integrated Systems [SiS] 85C503/5513
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 set
00:01.1 Ethernet controller: Silicon Integrated Systems [SiS] SiS900 10/100
Ethernet (rev 83)
Subsystem: Asustek Computer, Inc.: Unknown device 8035
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 52 min, 11 max, 32 set
Interrupt: pin C routed to IRQ 10
Region 0: I/O ports at d400 [size=256]
Region 1: Memory at eb800000 (32-bit, non-prefetchable) [size=4K]
Expansion ROM at <unassigned> [disabled] [size=128K]
Capabilities: [40] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME+
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:02.0 PCI bridge: Silicon Integrated Systems [SiS] 5591/5592 AGP (prog-if
00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 0 set
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: e9800000-e9ffffff
Prefetchable memory behind bridge: f0000000-feafffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
Subsystem: Asustek Computer, Inc.: Unknown device 8035
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Latency: 2 min, 24 max, 32 set
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 9800 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: Silicon Integrated Systems [SiS]: Unknown
device 6300 (rev 21) (prog-if 00 [VGA])
Subsystem: Asustek Computer, Inc.: Unknown device 8035
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 11
BIST result: 00
Region 0: Memory at f0000000 (32-bit, prefetchable) [size=128M]
Region 1: Memory at e9800000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at a800 [size=128]
Capabilities: [40] Power Management version 1
Flags: PMEClk- AuxPwr- DSI- D1+ D2+ PME-
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] AGP version 2.0
Status: RQ=15 SBA+ 64bit- FW- Rate=421
Command: RQ=0 SBA- AGP- 64bit- FW- Rate=
