hi ,this message was sent by atul .. but he accidentally sent it to the admin (moi) So I'am sharing this with the list .. regards Sandesh ----- Original Message ----- From: Atul Chitnis <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Cc: <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> Sent: Sunday, February 06, 2000 11:13 PM Subject: Re: MODEM IN LINUX > Check out http:/www.exocore.com/linux for details on the printing [roblem > and lots of other solutions. > > your modem does not recognise indian dialtones - add "X1" to your modem > initialisation string. > > AC > > -------------------------------------------------------- > Atul Chitnis | [EMAIL PROTECTED] (PGP:6011BCB8) > Exocore Consulting | http://www.exocore.com > Bangalore, India | +91(80)3440397 Fax +91(80)3341137 > -------------------------------------------------------- > > On Sun, 6 Feb 2000, VIJAYAKUMAR M wrote: > > > I am new to linux. I have installed RedHat Linux 6.1 on my PC having two > > HDD. Primary master is set for Windows98. Secondary for Linux. I have > > two problems. > > 1. I am not able to configure my HP DJ200 Inkjet printer in RedHat Linux > > 6.1 whereas Printer Port was autodetected in RedHat Linux 6. > > > > 2.I have a GVC 33.6 Kbps External modem. I am unable to dial up for > > connecting to internet using > > my GVC 33.6 modem. I would like to add some deatils which I feel would > > help you find a solution to this. > > In the setup of kppp, the settings under device tab goes like this. > > Modem Device /dev/ttys1 > > Flow Cotrol CRTSCTS > > Line Termination CR/LF > > Connection Speed 115200 > > Modem Time Out 60 Seconds > > > > On querying the modem the following results are obtained. > > > > ATI 33600 > > ATI 1 255 > > ATI 2 OK > > ATI 3 V2.200-V34_ACF_DS1 > > ATI 4 111151012000 r3000111170000000 > > ATI 5 022 > > ATI 6 RCV336DPFSP Rev 44BC > > ATI 7 255 > > > > The settings under modem tab is given below > > > > Busy wait 10 seconds > > Modem Volume set at Mid level. > > > > > > Modem commands. > > > > Pre Init Delay (sec/100) 51 > > Initialization String ATZ > > Post Init Delay (sec/100) 52 > > Init Response OK > > Dial String ATDT > > Connect Response CONNECT > > Busy Response BUSY > > No Carrier Response NO CARRIER > > No Dial Tone Response NO DIALTONE > > Hangup String ATH > > Hang Up Response OK > > Answer Respnse ATA > > Ring Response RING > > Answer Response CONNECT > > Escape String +++ > > Escape Response OK > > Guard Time 50 > > Volume Off/Low/High M0L0 M1L1 M1L4 > > > > The LoginScript window was open when dialing. The modem is initialised, > > Volume set and the command ATDT4404444 appears in the Login Script > > window. The Dial Tone could be heard from Modem. But there after Modem > > fails to Dial and NO DIALTONE appears in the Login Script Window. This > > is the case even if I try with Pulse Dialing. Please suggest. > > > > Thankyou > > > > VIJAYAKUMAR M > > > > To subscribe / unsubscribe goto the site www.ilug-bom.org ., click on the mailing list button and fill the appropriate information and submit. For any other queries contact the ML maintener
