On Thu, Nov 29, 2007 at 06:35:55PM +0300, Andrei Dolnikov wrote:
Hi Andrei. I have a few comments below.
> This patch adds new functionality to MV64x60 boot code. The changes are
> required
> to access DevCS windows registers and set PCI bus and devfn numbers for
> MV644x60
> PCI/PCI-X interfaces.
>
> Signed-off-by: Andrei Dolnikov <[EMAIL PROTECTED]>
>
> ---
> mv64x60.c | 74
> ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
> mv64x60.h | 10 ++++++++
> 2 files changed, 84 insertions(+)
>
> diff --git a/arch/powerpc/boot/mv64x60.c b/arch/powerpc/boot/mv64x60.c
> index d207a0b..787a124 100644
> --- a/arch/powerpc/boot/mv64x60.c
> +++ b/arch/powerpc/boot/mv64x60.c
> @@ -32,6 +32,16 @@
> #define MV64x60_CPU2MEM_3_BASE 0x0218
> #define MV64x60_CPU2MEM_3_SIZE 0x0220
>
> +#define MV64x60_DEV2MEM_WINDOWS 4
> +#define MV64x60_DEV2MEM_0_BASE 0x0028
> +#define MV64x60_DEV2MEM_0_SIZE 0x0030
> +#define MV64x60_DEV2MEM_1_BASE 0x0228
> +#define MV64x60_DEV2MEM_1_SIZE 0x0230
> +#define MV64x60_DEV2MEM_2_BASE 0x0248
> +#define MV64x60_DEV2MEM_2_SIZE 0x0250
> +#define MV64x60_DEV2MEM_3_BASE 0x0038
> +#define MV64x60_DEV2MEM_3_SIZE 0x0040
> +
These aren't device->memory windows, they're CPU->device windows so
they should be named MV64x60_CPU2DEV_xxx to be consistent with the
previously established naming convention.
> #define MV64x60_ENET2MEM_BAR_ENABLE 0x2290
> #define MV64x60_ENET2MEM_0_BASE 0x2200
> #define MV64x60_ENET2MEM_0_SIZE 0x2204
> @@ -219,6 +229,25 @@ static struct mv64x60_mem_win
> mv64x60_cpu2mem[MV64x60_CPU2MEM_WINDOWS] = {
> },
> };
>
> +static struct mv64x60_mem_win mv64x60_devcs[MV64x60_DEV2MEM_WINDOWS] = {
Why not call this mv64x60_cpu2dev[]?
<snip>
> @@ -586,6 +645,21 @@ u32 mv64x60_get_mem_size(u8 *bridge_base)
> return mem;
> }
>
> +/* Read a size of DEV_CS window */
> +u32 mv64x60_get_devcs_size(u8 *bridge_base, u32 devcs)
u32 mv64x60_get_cpu2dev_size(...)
<snip>
> diff --git a/arch/powerpc/boot/mv64x60.h b/arch/powerpc/boot/mv64x60.h
> index d0b29a7..a633d2e 100644
> --- a/arch/powerpc/boot/mv64x60.h
> +++ b/arch/powerpc/boot/mv64x60.h
> @@ -12,6 +12,14 @@
>
> #define MV64x60_CPU_BAR_ENABLE 0x0278
>
> +#define MV64x60_PCI0_MODE 0x0d00
> +#define MV64x60_PCI1_MODE 0x0d80
> +#define MV64x60_PCI0_P2P_CONF 0x1d14
> +#define MV64x60_PCI1_P2P_CONF 0x1d94
> +
> +#define MV64x60_PCI_MODE_MASK 0x00000030
> +#define MV64x60_PCI_CONVENTIONAL_MODE 0x00000000
> +
AFAICS these macros are only used in mv64x60.c so just put them there.
They only need to go in mv64x60.h if they're used in more than one .c
file.
Mark
_______________________________________________
Linuxppc-dev mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-dev