On Wed, 2018-08-08 at 06:28 +0000, Bharat Bhushan wrote: > > -----Original Message----- > > From: Scott Wood [mailto:o...@buserror.net] > > Sent: Wednesday, August 8, 2018 11:26 AM > > To: Bharat Bhushan <bharat.bhus...@nxp.com>; > > b...@kernel.crashing.org; pau...@samba.org; m...@ellerman.id.au; > > ga...@kernel.crashing.org; mark.rutl...@arm.com; > > kstew...@linuxfoundation.org; gre...@linuxfoundation.org; > > devicet...@vger.kernel.org; linuxppc-dev@lists.ozlabs.org; linux- > > ker...@vger.kernel.org > > Cc: r...@kernel.org; keesc...@chromium.org; tyr...@linux.vnet.ibm.com; > > j...@perches.com > > Subject: Re: [RFC 5/5] powerpc/fsl: Add supported-irq-ranges for P2020 > > > > On Wed, 2018-08-08 at 03:44 +0000, Bharat Bhushan wrote: > > > > -----Original Message----- > > > > From: Scott Wood [mailto:o...@buserror.net] > > > > Sent: Wednesday, August 8, 2018 2:44 AM > > > > To: Bharat Bhushan <bharat.bhus...@nxp.com>; > > > > b...@kernel.crashing.org; pau...@samba.org; m...@ellerman.id.au; > > > > ga...@kernel.crashing.org; mark.rutl...@arm.com; > > > > kstew...@linuxfoundation.org; gre...@linuxfoundation.org; > > > > devicet...@vger.kernel.org; linuxppc-dev@lists.ozlabs.org; linux- > > > > ker...@vger.kernel.org > > > > Cc: r...@kernel.org; keesc...@chromium.org; > > > > tyr...@linux.vnet.ibm.com; j...@perches.com > > > > Subject: Re: [RFC 5/5] powerpc/fsl: Add supported-irq-ranges for > > > > P2020 > > > > > > > > On Fri, 2018-07-27 at 15:18 +0530, Bharat Bhushan wrote: > > > > > MPIC on NXP (Freescale) P2020 supports following irq > > > > > ranges: > > > > > > 0 - 11 (External interrupt) > > > > > > 16 - 79 (Internal interrupt) > > > > > > 176 - 183 (Messaging interrupt) > > > > > > 224 - 231 (Shared message signaled interrupt) > > > > > > > > Why don't you convert to the 4-cell interrupt specifiers that make > > > > dealing with these ranges less error-prone? > > > > > > Ok , will do if we agree to have this series as per comment on other > > > patch. > > > > If you're concerned with errors, this would be a good things to do > > regardless. > > Actually, it seems that p2020si-post.dtsi already uses 4-cell interrupts. > > > > What is motivating this patchset? Is there something wrong in the > > existing > > dts files? > > There is no error in device tree. Main motivation is to improve code for > following reasons: > - While code study it was found that if a reserved irq-number used then > there are no check in driver. irq will be configured as correct and > interrupt will never fire.
Again, a wrong interrupt number won't fire, whether an interrupt by that number exists or not. I wouldn't mind a sanity check in the driver if the programming model made it properly discoverable, but I don't think it's worth messing with device trees just for this (and even less so given that there don't seem to be new chips coming out that this would be relevant for). > > > One other confusing observation I have is that "irq_count" from > > > platform code is given precedence over "last-interrupt-source" in > > > device- > > > > tree. > > > Should not device-tree should have precedence otherwise there is no > > > point using " last-interrupt-source" if platform code passes > > > "irq_count" in mpic_alloc(). > > > > Maybe, though I don't think it matters much given that last-interrupt- > > source > > was only added to avoid having to pass irq_count in platform code. > > Thanks for clarifying; > > My understanding was that "last-interrupt-source" added to ensure that we > can over-ride value passed from platform code. In that case we do not need > to change code and can control from device tree. The changelog says, "To avoid needing to write custom board-specific code to detect that scenario, allow it to be easily overridden in the device-tree," where "it" means the value provided by hardware. The goal was to pass in 256 without board code in the kernel, not to override the 256. -Scott