On Mon, May 19, 2008 at 10:30 AM, Guennadi Liakhovetski <[EMAIL PROTECTED]> wrote: > On Mon, 19 May 2008, Grant Likely wrote: >> But that is Linux internal >> details; this discussion is about device tree bindings. >> >> Note that I did say that drivers can define additional properties for >> supporting chip select changes as needed. I'm just not attempting to >> encode them into the formal binding. There is simply just too many >> different ways to manipulate chip select signals and so I don't feel >> confident trying to define a *common* binding at this moment in time. > > Yes, I understand, that physically there can be many ways SPI chipselects > can be controlled. But I thought there could be a generic way to cover > them all by defining a separate entry on your SPI bus. Like > > + SPI example for an MPC5200 SPI bus: > + [EMAIL PROTECTED] { > + #address-cells = <1>; > + #size-cells = <0>; > + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; > + reg = <0xf00 0x20>; > + interrupts = <2 13 0 2 14 0>; > + interrupt-parent = <&mpc5200_pic>; > + [EMAIL PROTECTED] { > + compatible = "oem,cs-type"; > + }; > + > + [EMAIL PROTECTED] { > + compatible = "micrel,ks8995m"; > + linux,modalias = "ks8995"; > + max-speed = <1000000>; > + reg = <0>; > + cs-parent = <&/.../[EMAIL PROTECTED]/[EMAIL > PROTECTED]>; > + }; > ... > + }; > > Then whatever method is used to actually switch the CS, a driver should be > registered to handle [EMAIL PROTECTED], providing the required calls. > Without such a driver [EMAIL PROTECTED] will not probe successfully. > Wouldn't this cover all possible cases? One could even consider actually > putting SPI devices on SPI chipselect busses, but that won't look very > elegant:-)
Hurrmmmm... I'm not so fond of this approach. cs-parent doesn't seem to make much sense to me. It might be better to have a cs-handler property on the SPI bus node instead of on the SPI slave nodes, but even then it leaves a number of questions about what it really means. In some cases it would be overkill. For example, if the SPI node simply had multiple GPIO lines then an extra cs-parent node wouldn't be needed at all. Then there are the complex arrangements. When setting CS requires inserting a special 'set cs' SPI message at the right time. Or worse; when setting CS requires /modifying/ the sent SPI message. Essentially, the binding would need to describe the ability to completely intercept and rewrite all SPI messages going through the CS scheme. I'm not saying it's not possible to do, but I am saying that I'd like to have a better feel for all the use cases before it is defined. I'm not convinced that adding a cs-parent phandle will do that appropriately. That being said, my gut feel is that the solution will be to support spi-bridge nodes that handle the complex CS configuration settings; the spi-bridge would be a child of the spi-master and the parent of the spi devices; and simple CS settings being handled with regular old GPIO bindings. (Much like the last suggestion you make; except that I think that it *does* looks elegant.) :-) example; here's an SPI bus that has 2 GPIOs for two bus CS lines and an SPI bridge that uses both CSes; one address for accessing the bridge's CS register and one CS to access the downstream devices. + SPI example for an MPC5200 SPI bus: + [EMAIL PROTECTED] { + #address-cells = <1>; + #size-cells = <0>; + compatible = "fsl,mpc5200b-spi","fsl,mpc5200-spi"; + reg = <0xf00 0x20>; + interrupts = <2 13 0 2 14 0>; + interrupt-parent = <&mpc5200_pic>; + gpios = <&gpio1 0 0 &gpio1 1 0>; + [EMAIL PROTECTED] { + compatible = "oem,spi-bridge-type"; + reg = < 0 1 >; // note: 2 SPI CS addresses; first one to access bridge registers + + [EMAIL PROTECTED] { + compatible = "micrel,ks8995m"; + linux,modalias = "ks8995"; + max-speed = <1000000>; + reg = <0>; + }; ... // and more SPI child nodes here... + }; + }; But even this doesn't reflect the hardware layout well. What if the SS lines are on SPI GPIO expanders on the same bus? Then does it make sense for them to be layed out as spi bridges? Cheers, g. -- Grant Likely, B.Sc., P.Eng. Secret Lab Technologies Ltd. _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-dev