Hi Herve, thanks for your patch!
On Tue, Sep 12, 2023 at 12:15 PM Herve Codina <herve.cod...@bootlin.com> wrote: > The Lantiq PEF2256 is a framer and line interface component designed to > fulfill all required interfacing between an analog E1/T1/J1 line and the > digital PCM system highway/H.100 bus. > > This kind of component can be found in old telecommunication system. > It was used to digital transmission of many simultaneous telephone calls > by time-division multiplexing. Also using HDLC protocol, WAN networks > can be reached through the framer. > > This pinmux support handles the pin muxing part (pins RP(A..D) and pins > XP(A..D)) of the PEF2256. > > Signed-off-by: Herve Codina <herve.cod...@bootlin.com> > Reviewed-by: Christophe Leroy <christophe.le...@csgroup.eu> > Signed-off-by: Christophe Leroy <christophe.le...@csgroup.eu> Nice to see this as a proper pin control driver! > drivers/pinctrl/pinctrl-pef2256-regs.h | 65 ++++++ > drivers/pinctrl/pinctrl-pef2256.c | 308 +++++++++++++++++++++++++ Do you really need a separate header just for some registers? But it's a matter of taste so I'm not gonna complain if you want it this way. > +config PINCTRL_PEF2256 > + tristate "Lantiq PEF2256 (FALC56) pin controller driver" > + depends on OF && FRAMER_PEF2256 > + select PINMUX select PINCONF > + select GENERIC_PINCONF This brings it in implicitly but I prefer that you just select it. > +/* SPDX-License-Identifier: GPL-2.0 */ > +/* I think SPDX mandates that you start the tag with C99 comments // SPDX-License-Identifier: GPL-2.0-only > + /* We map 1 group <-> 1 pin */ Also known as "the qualcomm trick", but hey: it's fine. > +static int pef2256_register_pinctrl(struct pef2256_pinctrl *pef2256) > +{ > + struct pinctrl_dev *pctrl; > + > + pef2256->pctrl_desc.name = dev_name(pef2256->dev); > + pef2256->pctrl_desc.owner = THIS_MODULE; > + pef2256->pctrl_desc.pctlops = &pef2256_pctlops; > + pef2256->pctrl_desc.pmxops = &pef2256_pmxops; > + if (pef2256->version == PEF2256_VERSION_1_2) { > + pef2256->pctrl_desc.pins = pef2256_v12_pins; > + pef2256->pctrl_desc.npins = ARRAY_SIZE(pef2256_v12_pins); > + pef2256->functions = pef2256_v12_functions; > + pef2256->nfunctions = ARRAY_SIZE(pef2256_v12_functions); > + } else { > + pef2256->pctrl_desc.pins = pef2256_v2x_pins; > + pef2256->pctrl_desc.npins = ARRAY_SIZE(pef2256_v2x_pins); > + pef2256->functions = pef2256_v2x_functions; > + pef2256->nfunctions = ARRAY_SIZE(pef2256_v2x_functions); > + } > + > + pctrl = devm_pinctrl_register(pef2256->dev, &pef2256->pctrl_desc, > pef2256); > + if (IS_ERR(pctrl)) { > + dev_err(pef2256->dev, "pinctrl driver registration failed\n"); > + return PTR_ERR(pctrl); > + } > + > + return 0; You could use return dev_err_probe(...); > + pef2256_reset_pinmux(pef2256_pinctrl); > + ret = pef2256_register_pinctrl(pef2256_pinctrl); > + if (ret) > + return ret; Or you could use it down here. With or without these changes (because they are nitpicks) Reviewed-by: Linus Walleij <linus.wall...@linaro.org> Yours, Linus Walleij