Hi, Idle routines on pseries were rearranged so that cpuidle can do an optimized idle state selection. However, until cpuidle takes over during boot, the idle loop spins for a short while. This actually affected bootup time since spinning idle sibling threads slows down master cpu that executes bootup code.
The following patch enables pseries system to yield to hypervisor and stop spinning by calling cede_processor() until cpuidle can take over and do optimal idle state selection. Bootup time can be reduced to half on small guest where most of the time is spend before device init. Thanks Ben for the review and suggestions. --Vaidy powerpc: Default arch idle could cede processor on pseries When adding cpuidle support to pSeries, we introduced two regressions: - The new cpuidle backend driver only works under hypervisors supporting the "SLPLAR" option, which isn't the case of the old POWER4 hypervisor and the HV "light" used on js2x blades - The cpuidle driver registers fairly late, meaning that for a significant portion of the boot process, we end up having all threads spinning. This slows down the boot process and increases the overall resource usage if the hypervisor has shared processors. This fixes it by implementing a "default" idle that will cede to the hypervisor when possible, in a very simple way without all the bells and whisles of cpuidle. Reported-by: Paul Mackerras <pau...@samba.org> Signed-off-by: Vaidyanathan Srinivasan <sva...@linux.vnet.ibm.com> Acked-by: Deepthi Dharwar <deep...@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <b...@kernel.crashing.org> diff --git a/arch/powerpc/platforms/pseries/setup.c b/arch/powerpc/platforms/pseries/setup.c index c11c823..54b998f 100644 --- a/arch/powerpc/platforms/pseries/setup.c +++ b/arch/powerpc/platforms/pseries/setup.c @@ -354,7 +354,7 @@ static int alloc_dispatch_log_kmem_cache(void) } early_initcall(alloc_dispatch_log_kmem_cache); -static void pSeries_idle(void) +static void pseries_lpar_idle(void) { /* This would call on the cpuidle framework, and the back-end pseries * driver to go to idle states @@ -362,10 +362,22 @@ static void pSeries_idle(void) if (cpuidle_idle_call()) { /* On error, execute default handler * to go into low thread priority and possibly - * low power mode. + * low power mode by cedeing processor to hypervisor */ - HMT_low(); - HMT_very_low(); + + /* Indicate to hypervisor that we are idle. */ + get_lppaca()->idle = 1; + + /* + * Yield the processor to the hypervisor. We return if + * an external interrupt occurs (which are driven prior + * to returning here) or if a prod occurs from another + * processor. When returning here, external interrupts + * are enabled. + */ + cede_processor(); + + get_lppaca()->idle = 0; } } @@ -456,15 +468,14 @@ static void __init pSeries_setup_arch(void) pSeries_nvram_init(); - if (firmware_has_feature(FW_FEATURE_SPLPAR)) { + if (firmware_has_feature(FW_FEATURE_LPAR)) { vpa_init(boot_cpuid); - ppc_md.power_save = pSeries_idle; - } - - if (firmware_has_feature(FW_FEATURE_LPAR)) + ppc_md.power_save = pseries_lpar_idle; ppc_md.enable_pmcs = pseries_lpar_enable_pmcs; - else + } else { + /* No special idle routine */ ppc_md.enable_pmcs = power4_enable_pmcs; + } ppc_md.pcibios_root_bridge_prepare = pseries_root_bridge_prepare; _______________________________________________ Linuxppc-dev mailing list Linuxppc-dev@lists.ozlabs.org https://lists.ozlabs.org/listinfo/linuxppc-dev