Please pardon the top post, it is done to help my local compatriots read more easily.
Andy, our MPC85xx_OPENPIC_IRQ_OFFSET is 80, but the call to openpic_init(MPC85xx_OPENPIC_IRQ_OFFSET) occurs after the two calls to openpic_set_sources. This leads me to believe that the mapping goes Internal irqs are 00..31 based on first openpic_set_sources(0, 32, ..) External irqs are 48..60 based on second openpic_set_sources(48, 12, ...) Then we have the openpic_init(80) call. So, I though the external IRQ0 was mapped to 48. But is it really mapped to 80 + 32 or 112 instead. If that is the case, there is another problem. The new problem is that if I set the irq to 112, when it is insmodded, I get an error from open_pic.c of the form: Open_pic.c:720 invalid irq 112 This seems to be coming from the macro at line 144 in open_pic.c #define check_arg_irq(irq) \ if (irq < open_pic_irq_offset || irq >= NumSources+open_pic_irq_offset \ || ISR[irq - open_pic_irq_offset] == 0) { \ printk("open_pic.c:%d: invalid irq %d\n", __LINE__, irq); \ dump_stack(); } Charles -----Original Message----- From: Andy Fleming [mailto:[EMAIL PROTECTED] Sent: Monday, April 30, 2007 5:23 PM To: Charles Krinke Cc: Sergei Shtylyov; Randy Brown; Chris Carlson; Kevin Smith; linuxppc-embedded@ozlabs.org Subject: Re: How do external irq's get mapped? On Apr 30, 2007, at 09:32, Charles Krinke wrote: > > > At this point, I would just like to confirm I am thinking clearly and > now understand the IRQ mapping. We are constrained to finish this > project with the kernel we started with, linux-2.6.17.11, so this > discussion is centered around that code base. This is my understanding > based on last week's e-mails and my research. > > 1. In arch/ppc/platforms/85xx/mpc85xx_cds_common.c is the > mpc85xx_cds_openpic_initsenses[] whose first 4 members are set to > IRQ_SENSE_LEVEL or'ed with IRQ_POLARITY_NEGATIVE. This means the first > four external interrupts are enabled and neg polarity. I can use these > entries as is and change the others from 0x0 as I need more of the > external interrupt pins. > > Just for reference, here are a few lines from mpc85xx_cds_init_IRQ > > mpc85xx_cds_init_IRQ(void) > { > openpic_set_sources(0, 32, OpenPIC_Addr + 0x10200); > /* Map PIC IRQs 0-11 */ > openpic_set_sources(48, 12, OpenPIC_Addr + 0x10000); This line is almost more important: openpic_init(MPC85xx_OPENPIC_IRQ_OFFSET); You need to find out what that is defined to be. My tree says it's defined as CPM_IRQ_OFFSET + NR_CPM_INTS (or 0, if CONFIG_CPM2 isn't defined). So that's the 80, if NR_8259_INTS is 16. Otherwise it's 64. So 112 could work, but if you have your config different, the numbers will move. > > 2. In this routine, the first openpic_set_source call is for the 32 > internal IRQ's and the second openpic_set_sources maps the 12 external > IRQ's beginning at 48, so that means my external IRQ mapping is: > > ExtIrQ LinuxIrqNum > 0 48 (first four are enabled) > 1 49 > 2 50 > 3 51 > 4 52 (last 8 not enabled by default) > 5 53 > 6 54 > 7 55 > 8 56 > 9 57 > 10 58 > 11 59 > > Is this correct? Depends on your configuration. But probably not. The CPM takes up some space, too. Andy _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded