Thomas, I had not an entry for Hip7 such that you send me! Thak you very much for your help. I'm going to chek my SDRAM initialization because, now, I see corrupted stamps, like these:
## Booting image at 00100000 ... Image Name: 2.2.4 Kernel for PQ2FADS Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 571353 Bytes = 558 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK Memory BAT mapping: BAT2=32Mb, BAT3=0Mb, residual: 0Mb ?Linux version 2.4.24 (gai otto at gexs22) (gcc version 3.3.2) #5 Tue Mar 9 17:00:09 CET 2004 ?ADS setup arch ?O n node 0 totalpages: 8192 ?zone(0): 8192 pages. ?zone(1): 0 pages. ?zone(2): 0 page s. ?Kernel command line: root=/dev/nfs rw nfsroot=172.16.246.111:/home/gaiotto/fa dsroot nobats ip=172.16.119.3 ????$ ?ADS init IRQ. NR_IR????? Regards, Stefano Thomas Sch?fer <tschaefer at giga-stream.de> on 09/03/2004 14:24:39 Please respond to <tschaefer at giga-stream.de> To: "Stefano Gaiotto" <Stefano.Gaiotto at marconi.com> cc: <linuxppc-embedded at lists.linuxppc.org> Subject: AW: Linux 2.4.24 on PQ2FADS Hi Stefano, just a wild guess: check the cpu_specs[] array in your arch/ppc/kernel/cputable.c file. It should contain something like this entry for your 8275 CPU: { /* 82xx (Hip7 603e cores) */ 0xffff0000, 0x80820000, "82xx (Hip7)", CPU_FTR_SPLIT_ID_CACHE | CPU_FTR_CAN_DOZE | CPU_FTR_USE_TB | CPU_FTR_CAN_NAP, COMMON_PPC, 32, 32, __setup_cpu_603 } The CPU ID (0x80820000 in this case) must match your 8275 CPU ID. Otherwise, generic PPC will be assumed which leads to strange behaviour as soon as the MMU will be enabled by the kernel. second guess: Because of the random errors you described I would check the SDRAM settings of the board: - check ALL settings of the memory controller against the settings described in the data sheet of your SDRAM. - check memory controller initialization sequence against the sequence described in the data sheet of the SDRAM and the memory controller of the CPU - if both are correct: check signal integrity on your board hope this helps. Best regards, Thomas Schaefer > -----Urspr?ngliche Nachricht----- > Von: owner-linuxppc-embedded at lists.linuxppc.org > [mailto:owner-linuxppc-embedded at lists.linuxppc.org]Im Auftrag von > Stefano Gaiotto > Gesendet: Dienstag, 9. M?rz 2004 13:53 > An: linuxppc-embedded at lists.linuxppc.org > Betreff: Linux 2.4.24 on PQ2FADS > > > > Dear colleagues, > > I'm trying to have Linux 2.4.24 working on my evaluation board PQ2FADS-VR > with ppc8275, but I'm suffering of a lot of instability problems. > The Boot-loader I use is Uboot-1.0.0 witch initialise correctly the board > at speed 66,133,199 and correctly fills bd_info struct. > But when I issue the command "=> bootm 100000" I observe every time a > different behaviour: sometimes I don't see anything, sometimes the board > stops in "Calibrating delay loop", sometimes after having written > the line: > > Memory: 30936k available (984k kernel code, 344k data, 52k init, 0k > highmem) > > Or the line > > POSIX conformance testing by UNIFIX > > Only occasionally it reaches the init program (stopping here). > > The same behaviour I observed with the images delivered by the Arabella > distribution! > > Do you have any suggestion? MMU? Cache? Hardware? > > Thanks in advance for your advice. > > With best regards, > > Stefano > > ** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/