I just tried a clean build, but the result is the same. When I built the kernel, I used TQM860L_config and make oldconfig, then edited some values with menuconfig (processor speed 80Mhz,ext2 support).
Is there anything else that I should change? Dan ppcboot 0.7.3 (Jan 19 2001 - 11:22:19) Initializing... CPU: XPC860xxZPnnD3 at 80 MHz: 4 kB I-Cache 4 kB D-Cache FEC present Board: ### No HW ID - assuming TQM8xxL DRAM: 16 MB FLASH: 8 MB In: serial Out: serial Err: serial => bootp;setenv bootargs init=/bin/bash root=/dev/nfs rw nfsroot=$(serverip):$(r ootpath) ip=$(ipaddr):$(serverip):$(gatewayip):$(netmask):$(hostname)::off;bootm BOOTP broadcast 1 ARP broadcast 1 TFTP from server 159.75.55.94; our IP address is 159.75.55.219 Filename '/tftpboot/pImage-TQM860L'. Load address: 0x100000 Loading: ####################################################################### #### done ## Booting Linux kernel at 00100000 ... Image Name: 2.2.14 for TQM860L Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 381908 Bytes = 372 kB = 0 MB Load Address: 00000000 Entry Point: 0000000c Verifying Checksum ... OK Uncompressing Kernel Image ... OK Linux version 2.2.14 (danf at gambit.iptest.com) (gcc version 2.95.2 19991024 (rele ase)) #11 Mon Jan 22 13:39:11 GMT 2001 Boot arguments: init=/bin/bash root=/dev/nfs rw nfsroot=159.75.55.94: ip=159.75. 55.219:159.75.55.94::255.255.255.0:tqmboard::off time_init: decrementer frequency = 300000000/60 Calibrating delay loop... 79.67 BogoMIPS Memory: 15208k available (700k kernel code, 444k data, 32k init) [c0000000,c1000 000] Dentry hash table entries: 2048 (order 2, 16k) Buffer cache hash table entries: 16384 (order 4, 64k) Page cache hash table entries: 4096 (order 2, 16k) POSIX conformance testing by UNIFIX Linux NET4.0 for Linux 2.2 Based upon Swansea University Computer Society NET3.039 NET4: Unix domain sockets 1.0 for Linux NET4.0. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP TCP: Hash tables configured (ehash 16384 bhash 16384) Starting kswapd v 1.5 CPM UART driver version 0.03 ttyS00 at 0x0280 is a SMC ttyS01 at 0x0380 is a SMC ttyS02 at 0x0100 is a SCC ttyS03 at 0x0200 is a SCC pty: 256 Unix98 ptys configured Found 2x16bit 4Mbyte CFI flash device of type AMD/Fujitsu standard at 40000000 registered flash device /dev/flash0 Found 2x16bit 4Mbyte CFI flash device of type AMD/Fujitsu standard at 40400000 registered flash device /dev/flash1 eth0: CPM ENET Version 0.2 on SCC1, 00:00:f8:51:78:10 Looking up port of RPC 100003/2 on 159.75.55.94 <----- By this point the LED neighbour table overflow on the eth port is off neighbour table overflow neighbour table overflow neighbour table overflow portmap: server 159.75.55.94 not responding, timed out Root-NFS: Unable to get nfsd port number from server, using default Looking up port of RPC 100005/1 on 159.75.55.94 neighbour table overflow neighbour table overflow neighbour table overflow neighbour table overflow portmap: server 159.75.55.94 not responding, timed out Root-NFS: Unable to get mountd port number from server, using default neighbour table overflow neighbour table overflow neighbour table overflow neighbour table overflow mount: server 159.75.55.94 not responding, timed out Root-NFS: Server returned error -5 while mounting /tftpboot/tqmboard VFS: Unable to mount root fs via NFS, trying floppy. request_module[block-major-2]: Root fs not mounted VFS: Cannot open root device 02:00 Kernel panic: VFS: Unable to mount root fs on 02:00 Rebooting in 180 seconds.. ** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/
