Hi Jan, I used EDK 9.1 and I have the opb_emac ethernet controller. I selected Xilinx 10/100 opb emac support in linux 2.6 configuration (device drivers/ Network device support/ Ethernet (10 or 100Mbit) ). Concerning sysace, you have downloaded linux 2.6 from denx or xilinx tree? I will try creating xsa nodes . Hope that it will work. Thanks Xavier
Jan Müller wrote: > > Hi, > > This is interesting... > > I have the sysace working but the ethernet not. > > Just an idea: > For the sysace driver in the 2.6 kernel the old device file > entries don't work anymore. > > Do you have the correct device nodes in /dev? You can create those > nodes with the following commands: > > # mknod -m 660 xsa b 254 0 > # mknod -m 660 xsa1 b 254 1 > # mknod -m 660 xsa2 b 254 2 > # mknod -m 660 xsa3 b 254 3 > > > Concerning the ethernet...: ;-) > Which IP Type do you have for the Ethernet_MAC? Mine is > xps_ethernetlite but I can't find a linux driver which seems to > work with this one. > > regards, > Jan > > > On Mon, Dec 15, 2008 at 01:12:18 -0800, xavier.vvv wrote: >> >> Hi, >> I have installed linux 2.6 on the xupv2p board. I have uart, ethernet, >> but >> sysace device is not working. >> I have seen in this forum that other persons have the problem. >> Could you tell me if you have sysace driver working? >> Also I want to install xenomai, but the problem is that linux from denx >> tree >> does not support opb_emac ethernet >> driver. I need Ethernet because I use nfs to access the root file system. >> So another question is: >> when you installed xenomai, where was the rfs? and did you used Ethernet >> driver? >> >> Thanks >> >> >> Joachim Meyer wrote: >> > >> > Hi >> > >> > I installed (with some help of this mailinglist) a Linux (Kernel 2.6.23 >> > from xilinx) on a ppc405 of a Virtex 2 PRO on a XUPV2P. Then I >> installed >> > Xenomai. Now I want to control some devices from the Board, so I >> thought >> > first I try to turn the LEDs on and of. I enabled the LEDs in my Design >> > without interrupt and also compiled the Kernel with Xilinx OPG GPIO >> > support. But I don't know realy how to go on. I found only 2 pages in >> the >> > internet which gave me a bit of information, but nothing helped me. >> > Can Anyone explain me what I have to do, or send me a link to a page >> where >> > it is explained? >> > >> > The 2 pages I found: >> > -------------------------- >> > http://osdir.com/ml/linux.uclinux.microblaze/2005-08/msg00120.html >> > http://www.tango-controls.org/Members/jbutanowicz/tango-on-ml403 >> > >> > The output of the kernel while booting: >> > ------------------------------------------------- >> > Linux version 2.6.23xlnx (me...@tiv007) (gcc version 3.4.5) #1 Thu Jul >> 17 >> > 12:10:27 CEST 2008 >> > Xilinx Generic PowerPC board support package (Xilinx XUPV2P) (Virtex-II >> > Pro) >> > Zone PFN ranges: >> > DMA 0 -> 65536 >> > Normal 65536 -> 65536 >> > Movable zone start PFN for each node >> > early_node_map[1] active PFN ranges >> > 0: 0 -> 65536 >> > Built 1 zonelists in Zone order. Total pages: 65024 >> > Kernel command line: console=ttyUL0 root=/dev/xsa2 rw >> > Xilinx INTC #0 at 0x41200000 mapped to 0xFDFFF000 >> > PID hash table entries: 1024 (order: 10, 4096 bytes) >> > Console: colour dummy device 80x25 >> > Console: Xilinx UART Lite >> > Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) >> > Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) >> > Memory: 257664k available (1580k kernel code, 500k data, 96k init, 0k >> > highmem) >> > Mount-cache hash table entries: 512 >> > NET: Registered protocol family 16 >> > Registering device uartlite:0 >> > Registering device xsysace:0 >> > Registering device xilinx_emac:0 >> > NET: Registered protocol family 2 >> > IP route cache hash table entries: 2048 (order: 1, 8192 bytes) >> > TCP established hash table entries: 8192 (order: 4, 65536 bytes) >> > TCP bind hash table entries: 8192 (order: 3, 32768 bytes) >> > TCP: Hash tables configured (established 8192 bind 8192) >> > TCP reno registered >> > io scheduler noop registered >> > io scheduler anticipatory registered (default) >> > io scheduler deadline registered >> > io scheduler cfq registered >> > uartlite.0: ttyUL0 at MMIO 0x40600003 (irq = 3) is a uartlite >> > console [ttyUL0] enabled >> > RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize >> > System ACE at 0x41800000 mapped to 0xD1020000, irq=1, 500472KB >> > xsa: xsa1 xsa2 >> > tun: Universal TUN/TAP device driver, 1.6 >> > tun: (C) 1999-2004 Max Krasnyansky <m...@qualcomm.com> >> > xilinx_emac xilinx_emac.0: MAC address is now 2: 0: 0: 0: 0: 0 >> > XEmac: using fifo mode. >> > XEmac: Detected PHY at address 0, ManufID 0x0013, Rev. 0x78e2. >> > eth0: Dropping NETIF_F_SG since no checksum feature. >> > eth0: Xilinx 10/100 EMAC at 0x80400000 mapped to 0xD1040000, irq=2 >> > eth0: XEmac id 1.1a, block id 32, type 1 >> > mice: PS/2 mouse device common for all mice >> > TCP cubic registered >> > NET: Registered protocol family 1 >> > NET: Registered protocol family 17 >> > kjournald starting. Commit interval 5 seconds >> > EXT3-fs warning: maximal mount count reached, running e2fsck is >> > recommended >> > EXT3 FS on xsa2, internal journal >> > EXT3-fs: recovery complete. >> > EXT3-fs: mounted filesystem with ordered data mode. >> > VFS: Mounted root (ext3 filesystem). >> > Freeing unused kernel memory: 96k init >> > INIT: version 2.85 booting >> > Welcome to DENX Embedded Linux Environment >> > Press 'I' to enter interactive startup. >> > Building the cache [ OK ] >> > storage network audio done[ OK ] >> > Cannot access the Hardware Clock via any known method. >> > Use the --debug option to see the details of our search for an access >> > method. >> > Setting clock : Thu Jan 1 00:00:20 UTC 1970 [ OK ] >> > Setting hostname localhost: [ OK ] >> > Checking filesystems >> > Checking all file systems. >> > [ OK ] >> > Mounting local filesystems: [ OK ] >> > Enabling swap space: [ OK ] >> > INIT: Entering runlevel: 3 >> > Entering non-interactive startup >> > Bringing up loopback interface: [ OK ] >> > Starting system logger: [ OK ] >> > Starting kernel logger: [ OK ] >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > XSysAce: Queue is plugged >> > Starting portmap: [ OK ] >> > Mounting NFS filesystems: XSysAce: Queue is plugged >> > [ OK ] >> > XSysAce: Queue is plugged >> > Mounting other filesystems: [ OK ] >> > >> > DENX ELDK version 4.1 build 2007-01-19 >> > Linux 2.6.23xlnx on a ppc >> > >> > localhost login: >> > >> > >> > >> > >> > >> > Thanks and Greez >> > Joachim >> > >> _________________________________________________________________________ >> > In 5 Schritten zur eigenen Homepage. Jetzt Domain sichern und >> gestalten! >> > Nur 3,99 EUR/Monat! http://www.maildomain.web.de/?mc=021114 >> > >> > _______________________________________________ >> > Linuxppc-embedded mailing list >> > Linuxppc-embedded@ozlabs.org >> > https://ozlabs.org/mailman/listinfo/linuxppc-embedded >> > >> > >> >> -- >> View this message in context: >> http://www.nabble.com/use-xilinx-gpio-from-linux-on-a-ppc405-tp18507061p21010485.html >> Sent from the linuxppc-embedded mailing list archive at Nabble.com. >> >> _______________________________________________ >> Linuxppc-embedded mailing list >> Linuxppc-embedded@ozlabs.org >> https://ozlabs.org/mailman/listinfo/linuxppc-embedded > _______________________________________________ > Linuxppc-embedded mailing list > Linuxppc-embedded@ozlabs.org > https://ozlabs.org/mailman/listinfo/linuxppc-embedded > > -- View this message in context: http://www.nabble.com/use-xilinx-gpio-from-linux-on-a-ppc405-tp18507061p21012378.html Sent from the linuxppc-embedded mailing list archive at Nabble.com. _______________________________________________ Linuxppc-embedded mailing list Linuxppc-embedded@ozlabs.org https://ozlabs.org/mailman/listinfo/linuxppc-embedded