My wireless card can find all of the networks in the surrounding area
including mine. I tried looking for the drivers for the wireless card
but I can't install them. My Hardware drivers says I don't have any
drivers installed in my computer.


de...@derek-laptop:~$ nm-tool

NetworkManager Tool

State: disconnected

- Device: eth0
-----------------------------------------------------------------
  Type:              Wired
  Driver:            8139too
  State:             unavailable
  Default:           no
  HW Address:        00:08:0D:BF:07:60

  Capabilities:
    Carrier Detect:  yes
    Speed:           10 Mb/s

  Wired Properties
    Carrier:         off


- Device: eth1
-----------------------------------------------------------------
  Type:              802.11 WiFi
  Driver:            orinoco_cs
  State:             disconnected
  Default:           no
  HW Address:        00:02:2D:7D:1D:55

  Capabilities:

  Wireless Properties
    WEP Encryption:  yes
    WPA Encryption:  yes

  Wireless Access Points
    Skynet:          Infra, 30:46:9A:52:76:B4, Freq 2437 MHz, Rate 54
Mb/s, Strength 100 WPA WPA2
    5UN46:           Infra, 00:1F:90:BE:D1:F4, Freq 2462 MHz, Rate 11
Mb/s, Strength 31 WEP
    linksys_SES_57828: Infra, 00:1D:7E:C7:9C:76, Freq 2437 MHz, Rate
54 Mb/s, Strength 37 WPA
    Skynet:          Infra, 30:46:9A:52:76:B4, Freq 2462 MHz, Rate 54
Mb/s, Strength 100 WPA WPA2
    NoMoreVerizon!:  Infra, 00:19:E3:FA:37:87, Freq 2412 MHz, Rate 11
Mb/s, Strength 35 WPA WPA2
    BBBSA:           Infra, 02:00:DC:72:EC:5A, Freq 2412 MHz, Rate 11
Mb/s, Strength 41 WEP
    BrownEyedGirl:   Infra, 00:1F:90:AD:7A:32, Freq 2452 MHz, Rate 54
Mb/s, Strength 62 WEP
    OFKX3:           Infra, 00:26:62:64:C8:B9, Freq 2437 MHz, Rate 54
Mb/s, Strength 82 WEP
    I Hate Linksys!: Infra, 00:1D:7E:91:07:5D, Freq 2437 MHz, Rate 54
Mb/s, Strength 31 WPA
    CATIC:           Infra, 00:22:3F:7D:3D:3C, Freq 2412 MHz, Rate 54
Mb/s, Strength 62 WPA


de...@derek-laptop:~$ lshw -C network
WARNING: you should run this program as super-user.
  *-network
       description: Ethernet interface
       product: RTL-8139/8139C/8139C+
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: a
       bus info: p...@0000:00:0a.0
       logical name: eth0
       version: 10
       serial: 00:08:0d:bf:07:60
       width: 32 bits
       clock: 33MHz
       capabilities: bus_master cap_list ethernet physical
       configuration: broadcast=yes driver=8139too
driverversion=0.9.28 latency=64 maxlatency=64 mingnt=32 multicast=yes
       resources: irq:11 ioport:ed00(size=256) memory:f7efff00-
f7efffff
  *-network
       description: Wireless interface
       physical id: 1
       logical name: eth1
       serial: 00:02:2d:7d:1d:55
       capabilities: ethernet physical wireless
       configuration: broadcast=yes driver=orinoco driverversion=0.15
firmware=Lucent/Agere 9.48 multicast=yes wireless=IEEE 802.11b
de...@derek-laptop:~$
de...@derek-laptop:~$ lshw -C network
WARNING: you should run this program as super-user.
PCI (sysfs)
  *-network
       description: Ethernet interface
       product: RTL-8139/8139C/8139C+
       vendor: Realtek Semiconductor Co., Ltd.
       physical id: a
       bus info: p...@0000:00:0a.0
       logical name: eth0
       version: 10
       serial: 00:08:0d:bf:07:60
       width: 32 bits
       clock: 33MHz
       capabilities: bus_master cap_list ethernet physical
       configuration: broadcast=yes driver=8139too
driverversion=0.9.28 latency=64 maxlatency=64 mingnt=32 multicast=yes
       resources: irq:11 ioport:ed00(size=256) memory:f7efff00-
f7efffff
  *-network
       description: Wireless interface
       physical id: 1
       logical name: eth1
       serial: 00:02:2d:7d:1d:55
       capabilities: ethernet physical wireless
       configuration: broadcast=yes driver=orinoco driverversion=0.15
firmware=Lucent/Agere 9.48 multicast=yes wireless=IEEE 802.11b



I believe my wireless card is a Realtek RTL 8139 (And yes, my wireless
network IS Skynet)

-- 
You received this message because you are subscribed to the Linux Users Group.
To post a message, send email to [email protected]
To unsubscribe, send email to [email protected]
For more options, visit our group at 
http://groups.google.com/group/linuxusersgroup

Reply via email to