Pozdrav vsem skup! Spet mam neki za vpraąat, sam ne se preveč smejat, če gre za res preproste stvari(mogoče pa niso) Prvo: moj modem je ena taka čeąka zadeva-CommWave 28.8 kbps PnP (ISA jasno). Zadevo naj bi nekako usposobil z isapnp oziroma najprej s pnpdump, ki naredi isapnp.conf datoteko, a očitno je neka napaka v njej, pri zagonu jo javi v vrstici 51. Prilagam dve verziji datoteke isapnp.conf (datoteki sta v v .txt obliki, ker sem ju kopiral v windows, prva je nedotaknjena, drugo-isapnp1 pa sem poskuąal urediti po spominu:) Še nekaj, v win se modem nahaja na com4, a da ga sistem sploh najde pri instalaciji na tem com portu, ga je treba prej instalirati na com 2 in com 5, če pa pol zbriąeą katerega od njih, pa noče klicat- to je čist resno... V isapnp.config bi modem bil tista kartica pod 02e8 Drugo: ali isapnp povsem instalira modem? Četrto: če vpiąem modem v mtab in fstab, odkod sporočilo 'Not in host:dir format' ? Uporabljam Red Hat 6.0 Upam , da bo kdo poznal odgovore na moja vpraąanja. Mimogrede, a kdo pozna kakąno dobro knjigo o linuxu, po moľnosti v slovenąčini, kjer bi bilo na preprost način opisano, kako začneą z linuxom. Mare PS:Zakaj so v konzoli, ko daą ukaz setfont lat2-16 pol neke turąke črke namesto naąih ąumnikov?
# $Id: pnpdump.c,v 1.18 1999/02/14 22:47:18 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information and FAQ on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR # # Trying port address 0203 # Board 1 has serial identifier 56 01 00 00 00 80 28 70 40 (DEBUG) (READPORT 0x0203) (ISOLATE PRESERVE) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING #Card 1: (serial identifier 56 01 00 00 00 80 28 70 40) #Vendor Id PCP2880, Serial Number 16777216, checksum 0x56. #Version 1.0, Vendor version 0.0 #ANSI string -->CommWave V.34PNP Data/Fax/Voice Modem<-- # Logical device id PCT2880 # Device support I/O range check register # Device supports vendor reserved register @ 0x38 # Device supports vendor reserved register @ 0x3a # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE PCP2880/16777216 (LD 0 # Multiple choice time, choose one only ! # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK)) # IRQ 3, 4, 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable Logical device decodes 16 bit IO address lines Minimum IO base address 0x02e8 Maximum IO base address 0x02e8 IO base alignment 8 bytes Number of IO addresses required: 8 (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK)) IRQ 3, 4, 5, 7, 9, 10 or 11. High true, edge sensitive interrupt (by default) (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK)) # IRQ 3, 4, 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK)) # IRQ 3, 4, 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # End dependent functions (NAME "PCP2880/16777216[0]{CommWave V.34PNP Data/Fax/Voice Modem}") (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY)
# $Id: pnpdump.c,v 1.18 1999/02/14 22:47:18 fox Exp $ # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of this file format, see isapnp.conf(5) # # For latest information and FAQ on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DNEEDSETSCHEDULER -DABORT_ONRESERR # # Trying port address 0203 # Board 1 has serial identifier 56 01 00 00 00 80 28 70 40 (DEBUG) (READPORT 0x0203) (ISOLATE PRESERVE) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING #Card 1: (serial identifier 56 01 00 00 00 80 28 70 40) #Vendor Id PCP2880, Serial Number 16777216, checksum 0x56. #Version 1.0, Vendor version 0.0 #ANSI string -->CommWave V.34PNP Data/Fax/Voice Modem<-- # Logical device id PCT2880 # Device support I/O range check register # Device supports vendor reserved register @ 0x38 # Device supports vendor reserved register @ 0x3a # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE PCP2880/16777216 (LD 0 # Multiple choice time, choose one only ! # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK)) # IRQ 3, 4, 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable Logical device decodes 16 bit IO address lines Minimum IO base address 0x02e8 Maximum IO base address 0x02e8 IO base alignment 8 bytes Number of IO addresses required: 8 (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK)) IRQ 3, 4, 5, 7, 9, 10 or 11. High true, edge sensitive interrupt (by default) (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK)) # IRQ 3, 4, 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK)) # IRQ 3, 4, 5, 7, 9, 10 or 11. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # End dependent functions (NAME "PCP2880/16777216[0]{CommWave V.34PNP Data/Fax/Voice Modem}") (ACT Y) )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY)