Lep pozdrav vsem..
Mene zanima a ima kdo od članov liste nameščene gonilnike za zydas od projekta zd1211.ath.cx ?
Sem poskušal že spraševati na njihovi ineteni listi, pa imam težave s prijavo nanjo. Zato tudi sprašujem zdaj na Lugos listi.
Osnoven problem je, da mi gonilnik zapremza računalo tako zelo, da je nemogoče tudi tipkati v konzolo, saj se znaki pojavijo na ekrano po pol minute. Problem sem malo bolje opisal v angleščini za njihovo interno listo in dodal dmesg..
Če kdo vidi kakšno napako bi bil zelo vesel namigov,
Lp,
Janes
Subject: No wireless extensions or extreme cpu usage
Hi!
First I want to say thanks for great effort to everybody.
My story is this. I've been trying to compile this driver ever since v.52
(noob:), but I had no luck till now.
Hi!
First I want to say thanks for great effort to everybody.
My story is this. I've been trying to compile this driver ever since v.52
(noob:), but I had no luck till now.
V.83 and a new slax install finaly builds the zd1221b module with no problems. I am using zd1211b cos of usb1.1 I have on my TP600. Modprobe loads it successfully and lsmod shows it loaded. And dmesg doesn't give out any suspicions there is something wrong..
But there are no interfaces.. only the local loopback.. ifconfig wlanx or
ethx up doesn't work.. unknown interface: no such device
Then I tried to build zd1211 which builds perfectly too, even autoloads,
has interfaces and I think it should connect, but the cpu usage is so high
it is imposibbly to work with computer (I have 300Mhz Thinkpad)..
I tried to search for a solution in archives, but didn't find nothing.
The zd1211 gives out dmesg errors unlike the zd1211b
Hope somebody can make any sense out.
zd1211 - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
usb 1-1: reset full speed USB device using uhci_hcd and address 2
Release Ver = 4330
zd1211:bulk out: wMaxPacketSize = 40
zd1211:bulk in: wMaxPacketSize = 40
zd1211:interrupt in: wMaxPacketSize = 40
zd1211:interrupt in: int_interval = 1
zd1211:bulk out: wMaxPacketSize = 40
EEPORM Ver = 4330
zd1211:USB Download Boot code success
zd1211:MAC address = 00:0e:2e:6c:1d:05
zd1211:AddrEntryTable = f7d4
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
zd1211:RF_Mode = 00000004
PA type: 0
AiroHa AL2230RF
zd1211:Pure B-Mode
zd1211:AllowedChannel = 000007ff
zd1211:LinkLEDn = 200
AllowedChannel = 000107ff
Region:48
zd1205: (exit) zd1205_config,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 2601
zd1205: (exit) zd1205_init,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 8570
usbcore: registered new driver zd1211
zd1205: (enter) zd1205_open,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4353
zd1205: (exit) zd1205_open,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4436
zd1205: (enter) zd1205_close,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4896
zd1211: failed rf reg_urb
zd1211:USB ST Code = -1
zd1205: (exit) zd1205_close,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4962
I should point out again, then when make $ ifconfig wlan0 up the
computer goes almost unresponsive due to high cpu usage or something..
i have to wait like half a minute only to see the characters i typed
into the console.
Good day to all,
Janes
But there are no interfaces.. only the local loopback.. ifconfig wlanx or
ethx up doesn't work.. unknown interface: no such device
Then I tried to build zd1211 which builds perfectly too, even autoloads,
has interfaces and I think it should connect, but the cpu usage is so high
it is imposibbly to work with computer (I have 300Mhz Thinkpad)..
I tried to search for a solution in archives, but didn't find nothing.
The zd1211 gives out dmesg errors unlike the zd1211b
Hope somebody can make any sense out.
zd1211 - http://zd1211.ath.cx/ - r83
Based on www.zydas.com.tw driver version 2.5.0.0
usb 1-1: reset full speed USB device using uhci_hcd and address 2
Release Ver = 4330
zd1211:bulk out: wMaxPacketSize = 40
zd1211:bulk in: wMaxPacketSize = 40
zd1211:interrupt in: wMaxPacketSize = 40
zd1211:interrupt in: int_interval = 1
zd1211:bulk out: wMaxPacketSize = 40
EEPORM Ver = 4330
zd1211:USB Download Boot code success
zd1211:MAC address = 00:0e:2e:6c:1d:05
zd1211:AddrEntryTable = f7d4
ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
zd1211:RF_Mode = 00000004
PA type: 0
AiroHa AL2230RF
zd1211:Pure B-Mode
zd1211:AllowedChannel = 000007ff
zd1211:LinkLEDn = 200
AllowedChannel = 000107ff
Region:48
zd1205: (exit) zd1205_config,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 2601
zd1205: (exit) zd1205_init,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 8570
usbcore: registered new driver zd1211
zd1205: (enter) zd1205_open,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4353
zd1205: (exit) zd1205_open,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4436
zd1205: (enter) zd1205_close,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4896
zd1211: failed rf reg_urb
zd1211:USB ST Code = -1
zd1205: (exit) zd1205_close,
/mnt/hda2/bekap/zd1211-driver-r83/src/zd1205.c line 4962
I should point out again, then when make $ ifconfig wlan0 up the
computer goes almost unresponsive due to high cpu usage or something..
i have to wait like half a minute only to see the characters i typed
into the console.
Good day to all,
Janes
_______________________________________________ lugos-list mailing list lugos-list@lugos.si http://liste2.lugos.si/cgi-bin/mailman/listinfo/lugos-list
