Bueno sigo con lo mismo ....y no la puedo ahcer andar ... repasemos
las configuracion a ver si viene por ahi el problema..
la idea es hacer ad.hoc entre 2 maquinas
A: con la placa Broadcom esta en cuestion
B: Con la placa Encore del otro thread qeu ya qeudo lista.
#####################
en B tenemos:
[EMAIL PROTECTED]:~$ifconfig wlan0
wlan0 Link encap:Ethernet HWaddr 00:40:F4:F2:82:20
inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0
inet6 addr: fe80::240:f4ff:fef2:8220/64 Scope:Link
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interrupt:12 Memory:dc010000-dc020000
[EMAIL PROTECTED]:~$iwconfig wlan0
Warning: Driver for device wlan0 recommend version 18 of Wireless Extension,
but has been compiled with version 17, therefore some driver features
may not be available...
wlan0 IEEE 802.11FH ESSID:"red" Nickname:"server_ara"
Mode:Ad-Hoc Frequency:2.412 GHz Cell: Not-Associated
Bit Rate=1 Mb/s Sensitivity=-200 dBm
RTS thr=2346 B Fragment thr=2346 B
Encryption key:off
Power Management:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[EMAIL PROTECTED]:~$iwlist wlan0 scan
Warning: Driver for device wlan0 recommend version 18 of Wireless Extension,
but has been compiled with version 17, therefore some driver features
may not be available...
wlan0 Scan completed :
Cell 01 - Address: EE:B3:B7:D7:01:B8
ESSID:"red"
Protocol:IEEE 802.11g
Mode:Ad-Hoc
Frequency:2.412 GHz (Channel 1)
Quality:0/100 Signal level:-30 dBm Noise level:-256 dBm
Encryption key:off
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 6 Mb/s
9 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Extra:bcn_int=100
Extra:atim=0
##################
Esto me hace pensar qeu las cosas en B estan bien... sera?
Las cosas en A estan:
dmesg reporta:
ieee80211_crypt: unregistered algorithm 'NULL'
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.7
ieee80211: Copyright (C) 2004-2005 Intel Corporation <[EMAIL PROTECTED]>
bcm43xx driver
ACPI: PCI Interrupt 0000:02:02.0[A] -> Link [C0F5] -> GSI 11 (level,
low) -> IRQ 11
bcm43xx: Chip ID 0x4318, rev 0x2
bcm43xx: Number of cores: 4
bcm43xx: Core 0: ID 0x800, rev 0xd, vendor 0x4243, enabled
bcm43xx: Core 1: ID 0x812, rev 0x9, vendor 0x4243, disabled
bcm43xx: Core 2: ID 0x804, rev 0xc, vendor 0x4243, enabled
bcm43xx: Core 3: ID 0x80d, rev 0x7, vendor 0x4243, enabled
bcm43xx: PHY connected
bcm43xx: Detected PHY: Version: 3, Type 2, Revision 7
bcm43xx: Detected Radio: ID: 8205017f (Manuf: 17f Ver: 2050 Rev: 8)
bcm43xx: Radio turned off
bcm43xx: Radio turned off
bcm43xx: PHY connected
bcm43xx: Radio turned on
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
bcm43xx: Chip initialized
bcm43xx: DMA initialized
bcm43xx: 80211 cores initialized
bcm43xx: Keys cleared
ADDRCONF(NETDEV_UP): eth2: link is not ready
bcm43xx: ASSERTION FAILED (radio_attenuation < 10) at:
drivers/net/wireless/bcm43xx/bcm43xx_phy.c:1485:bcm43xx_find_lopair()
root:~$ifconfig eth2
eth2 Link encap:Ethernet HWaddr 00:14:A5:15:CA:55
inet addr:192.168.0.2 Bcast:192.168.0.255 Mask:255.255.255.0
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:154 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:6636 (6.4 KiB)
Interrupt:11
root:~$iwconfig eth2
eth2 IEEE 802.11b/g ESSID:"red" Nickname:"Broadcom 4318"
Mode:Ad-Hoc Frequency=2.412 GHz Cell: Invalid
Bit Rate=11 Mb/s Tx-Power=18 dBm
RTS thr:off Fragment thr:off
Encryption key:off
Link Quality:0 Signal level:0 Noise level:0
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
root:~$iwlist eth2 scan
eth2 No scan results
#############
Algo no esta del todo bien (los firmware y todo eso estan ). No se
porque me tira en primera medida "Cell: Invalid"
alguien me podria tirar un poquito de luz sobre este asunto? gracias.
SAludos
PD: buscando y buscando por ahi, encontre una peticion online a la
gente de broadcom para que libere ese driver... desde ya que la firme
...
http://www.petitiononline.com/BCM4301/petition.html
2006/8/11, Ulises Cerviño Beresi <[EMAIL PROTECTED]>:
Probe la guía por puro gusto y funcionó de maravillas. Lo mejor de todo es
que yo tengo una de esas placas que dan problemas, bcm4318 AirForce, y no
hubo dramas.
> http://www.ubuntuforums.org/showthread.php?t=185174
>
Ah! Los drivers publicados en esa guía funcionan sin problemas.
Saludos,
--
Cerviño Ulises
--
-----
Angel Arancibia
GNU/Linux User Registered #358969
http://counter.li.org/
ICQ: 327093745
MSN: [EMAIL PROTECTED]
-------------------------------
"Computer science is no more about computers than astronomy is about
telescopes." - Edsger W. Dijkstra
"There are only 10 types of people in the world: Those who understand
binary, and those who don't"
_______________________________________________
Lugro mailing list
[email protected]
http://www.lugro.org.ar/mailman/listinfo/lugro
