The '$ modprobe -l lustre*' did not show any module on a patchless client. modprobe -v returns 'FATAL: Module lustre not found'.
How do I install a patchless client? I have tried lustre-client-modules and lustre-client-ver rpm packages in both sequences. Am I missing anything? Thanks, CS. On Tue, Jun 16, 2009 at 2:28 PM, Cliff White <cliff.wh...@sun.com> wrote: > Carlos Santana wrote: > >> The lctlt ping and 'net up' failed with the following messages: >> --- --- >> [r...@localhost ~]# lctl ping 10.0.0.42 >> opening /dev/lnet failed: No such device >> hint: the kernel modules may not be loaded >> failed to ping 10.0.0...@tcp: No such device >> >> [r...@localhost ~]# lctl network up >> opening /dev/lnet failed: No such device >> hint: the kernel modules may not be loaded >> LNET configure error 19: No such device >> > > Make sure modules are unloaded, then try modprobe -v. > Looks like you have lnet mis-configured, if your module options are wrong, > you will see an error during the modprobe. > cliffw > > --- --- >> >> I tried lustre_rmmod and depmod commands and it did not return any error >> messages. Any further clues? Reinstall patchless client again? >> >> - >> CS. >> >> >> On Tue, Jun 16, 2009 at 1:32 PM, Cliff White <cliff.wh...@sun.com<mailto: >> cliff.wh...@sun.com>> wrote: >> >> Carlos Santana wrote: >> >> I was able to run lustre_rmmod and depmod successfully. The >> '$lctl list_nids' returned the server ip address and interface >> (tcp0). >> >> I tried to mount the file system on a remote client, but it >> failed with the following message. >> --- --- >> [r...@localhost ~]# mount -t lustre 10.0.0...@tcp0:/lustre >> /mnt/lustre >> mount.lustre: mount 10.0.0...@tcp0:/lustre at /mnt/lustre >> failed: No such device >> Are the lustre modules loaded? >> Check /etc/modprobe.conf and /proc/filesystems >> Note 'alias lustre llite' should be removed from modprobe.conf >> --- --- >> >> However, the mounting is successful on a single node >> configuration - with client on the same machine as MDS and OST. >> Any clues? Where to look for logs and debug messages? >> >> >> Syslog || /var/log/messages is the normal place. >> >> You can use 'lctl ping' to verify that the client can reach the server. >> Usually in these cases, it's a network/name misconfiguration. >> >> Run 'tunefs.lustre --print' on your servers, and verify that mgsnode= >> is correct. >> >> cliffw >> >> >> Thanks, >> CS. >> >> >> >> >> >> On Tue, Jun 16, 2009 at 12:16 PM, Cliff White >> <cliff.wh...@sun.com <mailto:cliff.wh...@sun.com> >> <mailto:cliff.wh...@sun.com <mailto:cliff.wh...@sun.com>>> wrote: >> >> Carlos Santana wrote: >> >> Thanks Kevin.. >> >> Please read: >> >> http://manual.lustre.org/manual/LustreManual16_HTML/ConfiguringLustre.html#50401328_pgfId-1289529 >> >> Those instructions are identical for 1.6 and 1.8. >> >> For current lustre, only two commands are used for >> configuration. >> mkfs.lustre and mount. >> >> >> Usually when lustre_rmmod returns that error, you run it a >> second >> time, and it will clear things. Unless you have live mounts or >> network connections. >> >> cliffw >> >> >> I am referring to 1.8 manual, but I was also referring to >> HowTo >> page on wiki which seems to be for 1.6. The HowTo page >> >> http://wiki.lustre.org/index.php/Lustre_Howto#Using_Supplied_Configuration_Tools >> mentions abt lmc, lconf, and lctl. >> >> The modules are installed in the right place. The '$ >> lustre_rmmod' resulted in following o/p: >> [r...@localhost 2.6.18-92.1.17.el5_lustre.1.8.0smp]# >> lustre_rmmod >> ERROR: Module obdfilter is in use >> ERROR: Module ost is in use >> ERROR: Module mds is in use >> ERROR: Module fsfilt_ldiskfs is in use >> ERROR: Module mgs is in use >> ERROR: Module mgc is in use by mgs >> ERROR: Module ldiskfs is in use by fsfilt_ldiskfs >> ERROR: Module lov is in use >> ERROR: Module lquota is in use by obdfilter,mds >> ERROR: Module osc is in use >> ERROR: Module ksocklnd is in use >> ERROR: Module ptlrpc is in use by >> obdfilter,ost,mds,mgs,mgc,lov,lquota,osc >> ERROR: Module obdclass is in use by >> >> obdfilter,ost,mds,fsfilt_ldiskfs,mgs,mgc,lov,lquota,osc,ptlrpc >> ERROR: Module lnet is in use by ksocklnd,ptlrpc,obdclass >> ERROR: Module lvfs is in use by >> >> obdfilter,ost,mds,fsfilt_ldiskfs,mgs,mgc,lov,lquota,osc,ptlrpc,obdclass >> ERROR: Module libcfs is in use by >> >> obdfilter,ost,mds,fsfilt_ldiskfs,mgs,mgc,lov,lquota,osc,ksocklnd,ptlrpc,obdclass,lnet,lvfs >> >> Do I need to shutdown these services? How can I do that? >> >> Thanks, >> CS. >> >> >> On Tue, Jun 16, 2009 at 11:36 AM, Kevin Van Maren >> <kevin.vanma...@sun.com <mailto:kevin.vanma...@sun.com> >> <mailto:kevin.vanma...@sun.com <mailto:kevin.vanma...@sun.com>> >> <mailto:kevin.vanma...@sun.com >> <mailto:kevin.vanma...@sun.com> <mailto:kevin.vanma...@sun.com >> <mailto:kevin.vanma...@sun.com>>>> >> >> wrote: >> >> I think lconf and lmc went away with Lustre 1.6. Are you >> sure you >> are looking at the 1.8 manual, and not directions for >> 1.4? >> >> /usr/sbin/lctl should be in the lustre-<version> RPM. >> Do a: >> # rpm -q -l >> lustre-1.8.0-2.6.18_92.1.17.el5_lustre.1.8.0smp >> >> >> Do make sure the modules are installed in the right >> place: >> # cd /lib/modules/`uname -r` >> # find . | grep lustre.ko >> >> If it shows up, then do: >> # lustre_rmmod >> # depmod >> and try again. >> >> Otherwise, figure out where your modules are installed: >> # uname -r >> # cd /lib/modules >> # find . | grep lustre.ko >> >> >> You can also double-check the NID. On the MSD server, do >> # lctl list_nids >> >> Should show 10.0.0...@tcp0 >> >> Kevin >> >> >> >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Lustre-discuss mailing list >> Lustre-discuss@lists.lustre.org >> <mailto:Lustre-discuss@lists.lustre.org> >> http://lists.lustre.org/mailman/listinfo/lustre-discuss >> >> >> >> >> ------------------------------------------------------------------------ >> >> _______________________________________________ >> Lustre-discuss mailing list >> Lustre-discuss@lists.lustre.org >> http://lists.lustre.org/mailman/listinfo/lustre-discuss >> > >
_______________________________________________ Lustre-discuss mailing list Lustre-discuss@lists.lustre.org http://lists.lustre.org/mailman/listinfo/lustre-discuss