You can cancel this post. I wasn't sending traffic over 127.0.0.1 like i thought
On Mon, Jul 2, 2018 at 4:02 PM, Steve Stonebraker < steve.stonebra...@gmail.com> wrote: > I am unable to capture lvsadm traffic on the loopback interface. > > I am sucessfully sending traffic to my SIEM via ipvsadm. > > I was able to do this on both interfaces; ens192 and interface lo. > > I had no issues using tcpdump to view traffic being sent via ipvsadm on > interface ens192. > > My problem is that when i use tcpdump on interface lo I do not see any > ipvsadm traffic. > > > ** When I run tcpdump I don't see any udp traffic > # tcpdump -i lo -n udp port 51444 -vv > tcpdump: listening on lo, link-type EN10MB (Ethernet), capture size 262144 > bytes > > # ifconfig > ens192: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 > inet 10.0.10.136 netmask 255.255.255.0 broadcast 10.0.10.255 > > ether 00:50:56:ce:e3:dc txqueuelen 1000 (Ethernet) > RX packets 63480807660 bytes 12508576879467 (11.3 TiB) > RX errors 0 dropped 2 overruns 0 frame 0 > TX packets 19861938950 bytes 5978856268385 (5.4 TiB) > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 > > lo: flags=73<UP,LOOPBACK,RUNNING> mtu 65536 > inet 127.0.0.1 netmask 255.0.0.0 > inet6 ::1 prefixlen 128 scopeid 0x10<host> > loop txqueuelen 1 (Local Loopback) > RX packets 351855 bytes 1689650676 (1.5 GiB) > RX errors 0 dropped 0 overruns 0 frame 0 > TX packets 351855 bytes 1689650676 (1.5 GiB) > TX errors 0 dropped 0 overruns 0 carrier 0 collisions 0 > > > ** ipvsadm commands to set up round robin load balancing to three SIEM > nodes ** > > # ipvsadm -A -u 127.0.0.1:51444 -s rr -o > # ipvsadm -a -u 127.0.0.1:51444 -r 10.10.10.77:514 -m -w 1 > # ipvsadm -a -u 127.0.0.1:51444 -r 10.10.10.78:514 -m -w 1 > # ipvsadm -a -u 127.0.0.1:51444 -r 10.10.10.79:514 -m -w 1 > > # ipvsadm > IP Virtual Server version 1.2.1 (size=4096) > Prot LocalAddress:Port Scheduler Flags > -> RemoteAddress:Port Forward Weight ActiveConn InActConn > UDP localhost:51444 rr ops > -> 10.10.10.77:syslog Masq 1 0 1 > -> 10.10.10.78:syslog Masq 1 0 2 > -> 10.10.10.79:syslog Masq 1 0 2 > > _______________________________________________ Please read the documentation before posting - it's available at: http://www.linuxvirtualserver.org/ LinuxVirtualServer.org mailing list - lvs-users@LinuxVirtualServer.org Send requests to lvs-users-requ...@linuxvirtualserver.org or go to http://lists.graemef.net/mailman/listinfo/lvs-users