If the plug is not polarized then there is no hot or neutral.
One wire IS hot (swings from -120v to +120v relative to GND).
And one wire IS neutral (stays at 0v relative to GND).
Relative to each other, it's the same 120vac either direction, or
rather, there is no such thing as a direction.
But if the plug is not polarized then you have to treat both wires as
equally hot, since every time it's plugged in either side could be the
hot side that time, at random.
Switches come in all kinds of arrangements, so the only way to know how
to wire this particular switch is to test it with a continuity tester
and observe what connections it makes in each position, or consult it's
datasheet. Sometimes there is a diagram of the connections drawn right
on the body, otherwise google it's model number or find the datasheet
from the website where you got it or perhaps it's packaging.
A rocker with 3 pins and 2 positions (you didn't say how many positions
btw so I'm assuming) is fairly likely to be a center-common SPDT on-on,
hopefully non-shorting (break-before-make). Meaning the center pin is
connected to either one side or the other at any given time. When you're
turning one pin off, you're also turning the other pin on at the same
time. In this case since yoiu only care about turning something on/off,
you would just use the common pin and either one of the others. You just
run your hot wire from the wall to the center pin and connect the load
to either of the other pins, either one, doesn't matter, but only one,
and leave the other pin unconnected. (might want to cover it with
heat-shrink)
Except that is just one common configuration and might not be right for
your switch.
Really the switch could be totally different. It might have 3 positions
and be on-off-on, or the common pin might not be the center pin, or it
could be a lighted switch where only 2 pins are for switching and the
3rd pin is to power the light, and that light may also possibly not take
the same voltage as what's passing through the main pins.
Even a lighted switch where at least one of the pins is definitely
special and different, still doesn't necessarily have a right way to
wire it, since it's still up to you to decide when you want the light to
be on. Usually you want the light to reflect the power state, on when
the device is turned on. Or maybe you want the light to be a pilot light
that is on at all times so that you can find it in the dark, or so that
it indicates when power is available to the device rather than
indicating when the device is turned on.
There is unlikely to be a particular pin for GND. It's possible if the
switch has a metal body, or for example light switches in walls, or if
it has a light it might have a specific gnd pin, but generally there is
no such thing as a gnd pin on a switch, they are just contacts which you
connect to whatever your application requires. The closest thing to a
right or wrong is a general rule that for a mains power switch would be
to switch the hot side rather than the neutral side, simply so that when
it's in the off position, the least amount of things are hot.
But since you have a non-polarized plug, both wires are equally likely
to be hot at any given time, and so you just pick either one for the
switch, and treat the entire inside of the box as hot, and make sure the
whole box is well sealed and insulated, and users are well protected
from the internals. Or better, get rid of the non-polarized plug and use
a polarized one, and then you have an actual hot side to treat as the
hot side.
--
bkw
On 12/5/22 21:52, Spencer wrote:
Hello
Got a wiring question.
I built a simple 18VDC PS from JameCo and I put it in a project box.
I've added two pots for adjusting power, banana plugs for external
power, two mini voltmeters and will add a USB port for 5VDC. All this
works but now I want to add a AC rocker. The above was simple except
for the meticulous care that's needed to drill into a metal box. Now the
next item I want to add is an AC rocker switch but I'm a bit unsure how.
It's a 3 terminal AC rocker, and my understanding is the bronze terminal
is ground, the center is the power source, and the 3rd one is
accessory/load. What confuses me is the proper way to wire it. If the
plug was polarized I wouldn't be confused. I've attached a photo of the
back of the PS which shows the two power supply wires (one with writing
and the other none). The videos I've seen doesn't explain which is
power/live and which is ground using this type of wire. The plug isn't
polarized so it's not easy for me to determine + from -. I put a meter
to the wires inside the PS and it shows 119 and if I switch the probes
it still shows 119. What I was expecting was to see -119 when the probes
were wrong and this would've told me which is + and - but it didn't. So
which wire goes to the power source terminal and which wire goes to the
ground terminal? Do I simply wire it by wiring together the wires with
writing and the wires without writing? I hope I've made sense.
Thanks
--
bkw