On Sunday, September 25, 2016 at 4:52:54 PM UTC+5:30, Schooner wrote: > > > On 25/09/16 10:01, hector ice wrote: > > Hi all, > I am also trying to install xenomai patched kernel on my BBB for > preemption and RT Processing for my project. > I have followed the steps described here and also available on other > forums. But still I am not able to successfully develop the kernel. > > I have tried following steps.( I am using newest version of BBB rev.C) > 1. I have downloaded new 3.8 kernel ( as from webs I came to know that > xenomai is available till 3.8) > 2. I have did menuconfig, Than applied the patch of xenomai.and compiled > the kernel. > > > Normally you would patch the kernel and THEN configure it for building - > no idea what options you used. > But you should not need to build your own > > I need all the peripherals including pwm ,uart, i2c,spi to be up and running with other features so was trying to build. I agree ,Pre-built kernel is very good option. so will do on that.
> 3. When I have inserted the card with compiled kernel on BBB it gave me > 'kernel panic' and stopped booting > > --Than I did follow. > 1. I did again fresh installation. again with minimal modules selected. > But still no luck. > > Can anyone help me for this.? > > > There are pre-built kernels available as previously in this thread and as > Charles shows below > > http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#2014-05-14_GPG_error:_Optional_enable:_http:.2F.2Frepos.rcn-ee.com.2F > > They are at > http://repos.rcn-ee.com/debian/pool/main/l/linux-3.8.13-xenomai-r76/ > with headers and firmware > > I checked link. Its says .deb package. I though prebuild kernel would be the whole kernel with xenomai. Around some Gb's. By the way in short I have project where I need full RT support with Preempt in kernel level. Please don't mind as I have tried some ways searched from net. that didn't worked So If that .deb package serves the need. I am more happy to go with it. > > > On Sunday, February 14, 2016 at 10:13:08 PM UTC+5:30, Charles Steinkuehler > wrote: >> >> On 2/14/2016 10:07 AM, Aleksandr Kolomeetc wrote: >> > Hello! >> > machinekit@beaglebone:~$ sudo apt-get install >> > linux-image-xenomai.beaglebone-omap >> > Reading package lists... Done >> > Building dependency tree >> > Reading state information... Done >> > E: Unable to locate package linux-image-xenomai.beaglebone-omap >> > E: Couldn't find any package by regex >> 'linux-image-xenomai.beaglebone-omap' >> > >> > I also can't to locate this package the >> > address: http://deb.dovetail-automata.com >> > What's wrong? >> >> Kernel packages are now built by Robert C. Nelson and can be found in >> the standard BeagleBone repos: >> >> http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#Kernel_Options >> >> ...if you're running an older image, you may need to add the new >> BeagleBone repositories to your apt sources list: >> >> >> http://elinux.org/Beagleboard:BeagleBoneBlack_Debian#2014-05-14_GPG_error:_Optional_enable:_http:.2F.2Frepos.rcn-ee.com.2F >> >> >> -- >> Charles Steinkuehler >> cha...@steinkuehler.net >> > -- > website: http://www.machinekit.io blog: http://blog.machinekit.io github: > https://github.com/machinekit > --- > You received this message because you are subscribed to the Google Groups > "Machinekit" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to machinekit+...@googlegroups.com <javascript:>. > Visit this group at https://groups.google.com/group/machinekit. > For more options, visit https://groups.google.com/d/optout. > > > -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to machinekit+unsubscr...@googlegroups.com. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout.
