Read the gist that Michael did for the DE0
Specifically here
https://gist.github.com/mhaberler/89a813dc70688e35d8848e8e467a1337
where you will see exactly the same error message you report,
because the MAC address is not set.
There is a link to it in the blogs.
You have to set the NIC MAC address etc and then restart
On 06/02/2018 23:54, mugginsac wrote:
I finally got the USB console working under
stretch.
I didn't have the dtb file that it was looking
(socfpga_cyclone5_de10_nano.dtb) for in the
boot/dtbs/4.9.68-socfpga-r3/ directory.
After I fixed that it is either loading the kernel or trying
to load the kernel. It is getting a crc error and then
starting over to try and load the kernel.
Any help interpreting what it is telling me would be greatly
appreciated. The log is below:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2018.02.06 15:47:15
=~=~=~=~=~=~=~=~=~=~=~=
U-Boot SPL 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14)
drivers/ddr/altera/sequencer.c: Preparing to start memory
calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
Trying to boot from MMC1
U-Boot 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14 -0800)
CPU: Altera SoCFPGA Platform
FPGA: Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT: SD/MMC Internal Transceiver (3.0V)
Watchdog enabled
I2C: ready
DRAM: 1 GiB
MMC: dwmmc0@ff704000: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Terasic DE10-Nano
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Hit any key to stop autoboot: 2 1 0
switch to partitions #0, OK
mmc0 is current device
Scanning mmc 0:2...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
179 bytes read in 21 ms (7.8 KiB/s)
1: Linux 4.9.68-socfpga-r3
Retrieving file: /boot/vmlinuz-4.9.68-socfpga-r3
5455176 bytes read in 380 ms (13.7 MiB/s)
append: root=/dev/mmcblk0p2 ro rootfstype=ext4 rootwait quiet
Retrieving file:
/boot/dtbs/4.9.68-socfpga-r3/socfpga_cyclone5_de10_nano.dtb
14997 bytes read in 45 ms (325.2 KiB/s)
## Flattened Device Tree blob at 02000000
Booting using the fdt blob at 0x2000000
reserving fdt memory region: addr=0 size=1000
Loading Device Tree to 03ff9000, end 03fffa94 ... OK
Starting kernel ...
U-Boot SPL 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14)
drivers/ddr/altera/sequencer.c: Preparing to start memory
calibration
drivers/ddr/altera/sequencer.c: CALIBRATION PASSED
drivers/ddr/altera/sequencer.c: Calibration complete
Trying to boot from MMC1
U-Boot 2018.01-rc1-dirty (Jan 25 2018 - 15:56:14 -0800)
CPU: Altera SoCFPGA Platform
FPGA: Altera Cyclone V, SE/A6 or SX/C6 or ST/D6, version 0x0
BOOT: SD/MMC Internal Transceiver (3.0V)
Watchdog enabled
I2C: ready
DRAM: 1 GiB
MMC: dwmmc0@ff704000: 0
*** Warning - bad CRC, using default environment
In: serial
Out: serial
Err: serial
Model: Terasic DE10-Nano
Net:
Error: ethernet@ff702000 address not set.
No ethernet found.
Hit any key to stop autoboot: 2 0
--
website: http://www.machinekit.io blog: http://blog.machinekit.io
github: https://github.com/machinekit
---
You received this message because you are subscribed to the
Google Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from
it, send an email to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
--
website: http://www.machinekit.io
blog: http://blog.machinekit.io
github: https://github.com/machinekit
---
You received this message because you are subscribed to the Google
Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from it,
send an email to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
--
website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit
---
You received this message because you are subscribed to the Google Groups "Machinekit" group.
To unsubscribe from this group and stop receiving emails from it, send an email to machinekit+unsubscr...@googlegroups.com.
Visit this group at https://groups.google.com/group/machinekit.
For more options, visit https://groups.google.com/d/optout.
|