MDAC that's what i meant, been years so couldn't remember! -----Original Message----- From: Peter Horsbøll Møller [mailto:[EMAIL PROTECTED] Sent: Thursday, 13 October 2005 3:24 PM To: Simmonds, Ashley (DTEI); mapinfo-l@lists.directionsmag.com Cc: Churchill, Ron; Lee, Norman Subject: RE: MI-L MapInfo 8.0 doesn't open Access files
I think the jet engine is part of the MDAC installation, so maybe you should try installing the latest version of MDAC ? Peter Horsbøll Møller GIS Developer, MTM Geographical Information & IT COWI A/S Odensevej 95 DK-5260 Odense S. Denmark Tel +45 6311 4900 Direct +45 6311 4908 Mob +45 5156 1045 Fax +45 6311 4949 E-mail [EMAIL PROTECTED] http://www.cowi.dk/gis COWI har fået ny hjemmeside. Ydelserne GIS og IT, kort, kortlægning, 3D visualisering og arealforvaltning ligger under SAMFUND. Se mere her : www.cowi.dk COWI has changed its homepage. Our services within cadastre and landadministration, geodataproducts, mapping and GIS can be seen under SOCIETY. See our services here: www.cowi.com -----Original Message----- From: Simmonds, Ashley (DTEI) [mailto:[EMAIL PROTECTED] Sent: Thursday, October 13, 2005 4:07 AM To: mapinfo-l@lists.directionsmag.com Cc: Churchill, Ron; Lee, Norman Subject: RE: MI-L MapInfo 8.0 doesn't open Access files actually i don't think it's an MI issue, it sounds like you need the jet DLL's reinstalled. sorry i can't recall the exact stuff right now it's been a while, but get one of your resident nerds to make sure the latest patches for Jet and stuff are applied to Office. -----Original Message----- From: Fonseca, Milton [mailto:[EMAIL PROTECTED] Sent: Thursday, 13 October 2005 6:31 AM To: mapinfo-l@lists.directionsmag.com Cc: Churchill, Ron; Lee, Norman Subject: MI-L MapInfo 8.0 doesn't open Access files Hello, We just upgraded MapInfo 6.0 to version 8.0 on a XP computer. The new MapInfo 8.0 refuses to open ANY Access files that we could open before. It gives the following error message: The Microsoft Jet Engine is not available for error information It can not also save a regular .tab file to an Access .mdb file. All the files we tested open with no problem in Access. The same files open fine in 2 other computers that have MapInfo 8.0 and XP. We have tried the usual trouble shooting to fix the problem to no avail. Checked to see if there were any .ldb file left to prevent opening the .mdb file, installed the most current patch for version 8, uninstalled and re-installed MapInfo 8.0 (patch included), uninstalled and re-installed Access. I am fresh out of ideas, any suggestions? Milton Fonseca Research Analyst II (GIS) Mineral Hazards Mapping Project California Geological Survey California Department of Conservation Phone: (916) 323-8192 [EMAIL PROTECTED] CONFIDENTIALITY NOTICE: This communication is intended only for the use of the individual or entity to which it is addressed. This message contains information from the State of California, California Geological Survey, which may be privileged, confidential and exempt from disclosure under applicable law, including the Electronic Communications Privacy Act. If the reader of this communication is not the intended recipient, you are hereby notified that any dissemination, distribution, or copying of this communication is strictly prohibited. --------------------------------------------------------------------- List hosting provided by Directions Magazine | www.directionsmag.com | To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] Message number: 18243 --------------------------------------------------------------------- List hosting provided by Directions Magazine | www.directionsmag.com | To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] Message number: 18245 --------------------------------------------------------------------- List hosting provided by Directions Magazine | www.directionsmag.com | To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] Message number: 18247