On Tue, 2010-07-13 at 14:33 +0530, Amit Pundir wrote: > On Tue, Jul 13, 2010 at 9:19 AM, vijay singh <testmrs....@gmail.com> wrote: > > On Mon, 2010-07-12 at 17:05 +0300, Ameya Palande wrote: > >> Hi Vijay, > >> > >> On Mon, 2010-07-12 at 09:05 +0200, ext vijay singh wrote: > >> > I have tried image from below location for DevKit8000: > >> > > >> > //http://wiki.meego.com/ARM/Meego_on_Beagleboard_from_scratch#Make_X_start > >> > > >> > but i couldn't able to boot kernel. > >> > >> Can you post the kernel output from serial console and the .config file > >> that you used for building this kernel? > > > > I have used kernel image from below location : > > //http://wiki.meego.com/ARM/Meego_on_the_Beagle > > Check for section "Steps to modify an N900 image for BeagleBoard " > > > > Hi, > > Shouldn't you be running devkit8000 kernel instead? > > Check the following thread to get the devkit8000 kernel and uboot source > links: > http://groups.google.com/group/beagleboard/browse_thread/thread/3e02302066a6c003?pli=1 > > regards, > Amit Pundir > > > > Serial console O/P : > > > > ******************************************************************* > > Texas Instruments X-Loader 1.41 > > Starting OS Bootloader... > > U-Boot 1.3.3-svn333 (Sep 10 2009 - 16:49:01) > > > > OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz > > OMAP3 DevKit8000 Board + LPDDR/NAND > > DRAM: 128 MB > > NAND: 128 MiB > > In: serial > > Out: serial > > Err: serial > > > > Hit any key to stop autoboot: 0 > > > > OMAP3 DevKit8000 # setenv bootargs 'console=ttyS2,115200n8 > > root=/dev/mmcblk0p3 rootdelay=1' > > OMAP3 DevKit8000 # mmcinit > > OMAP3 DevKit8000 # fatload mmc 0 82000000 uImage > > > > reading uImage > > > > 1986880 bytes read > > > > OMAP3 DevKit8000 # bootm 82000000 > > ## Booting kernel from Legacy Image at 82000000 ... > > Image Name: Linux-2.6.34-beagle > > Image Type: ARM Linux Kernel Image (uncompressed) > > Data Size: 1986816 Bytes = 1.9 MB > > Load Address: 80008000 > > Entry Point: 80008000 > > Verifying Checksum ... OK > > Loading Kernel Image ... OK > > OK > > Starting kernel ... > > Uncompressing Linux... done, booting the kernel. > > ******************************************************************* > > > > After that nothing will happen. > > > > Please let me know boot arg are correct ?? > > or Do i have to use other configuration. > > > > If you have working configuration then please send it to me. > > > > > > Regards, > > vij > > > >> > >> Cheers, > >> Ameya.
Hi, I have tried with one of Beagle board kernel (Working previously) & it's boot up but still have problem with getting X. I have attached boot log. In summary i am getting below error (If i will run TWM manager): ******************************************* /usr/bin/xsetroot: unable to open display '' /usr/bin/twm: unable to open display "" /usr/bin/xterm Xt error: Can't open display: /usr/bin/xterm: DISPLAY is not set ******************************************* Please check. Regards, Vij > >> > >> _______________________________________________ > >> MeeGo-dev mailing list > >> MeeGo-dev@meego.com > >> http://lists.meego.com/listinfo/meego-dev > > > > > > _______________________________________________ > > MeeGo-dev mailing list > > MeeGo-dev@meego.com > > http://lists.meego.com/listinfo/meego-dev > > > _______________________________________________ > MeeGo-dev mailing list > MeeGo-dev@meego.com > http://lists.meego.com/listinfo/meego-dev
MeeGo_On_DevKit8000_Log.rtf
Description: RTF file
_______________________________________________ MeeGo-dev mailing list MeeGo-dev@meego.com http://lists.meego.com/listinfo/meego-dev